31105C
1.INSTALL TRANSAXLE CASE STRAIGHT PIN
| *a | Protrusion Height |
Using a plastic-faced hammer, install 3 new transaxle case straight pins to the transaxle(MTM) case sub-assembly to the specified protrusion height.
10.5 to 11.5 mm (0.413 to 0.453 in.)
41311E
2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case sub-assembly.
Do not deform the front differential case front tapered roller bearing (inner race) cage.
| *a | Align the protrusion with the groove |
Install the front differential oil baffle to the transaxle(MTM) case sub-assembly.
Align the protrusion of the front differential oil baffle with the groove of the transaxle(MTM) case sub-assembly.
Be sure to install the front differential oil baffle in the correct direction.
Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle(MTM) case sub-assembly.
41311F
3.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case sub-assembly.
Do not deform the front differential case rear tapered roller bearing (inner race) cage.
| *a | Wooden Block |
Using SST, a hammer and wooden block, install a new front differential case rear tapered roller bearing (outer race) together with the front differential case rear shim to the manual transmission case.
Use a front differential case rear shim of the same thickness as the removed one.
4.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.
Coat the differential case assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.
Install the manual transmission case to the transaxle(MTM) case sub-assembly with the 18 bolts.
| *1 | Front Differential Case Rear Shim |
Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.
Using SST and a torque wrench, measure the preload.
1.50 to 2.30 N*m (16 to 23 kgf*cm, 14 to 20 in.*lbf)
0.24 to 0.37 N*m (2.5 to 3.7 kgf*cm, 2.2 to 3.2 in.*lbf)
If the preload is not as specified, replace the front differential case rear shim with one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the preload is within the specification.
| Part No. | Thickness mm (in.) | Mark | Part No. | Thickness mm (in.) | Mark |
|---|---|---|---|---|---|
| 90564-61095 | 2.050 (0.0807) | A | 90564-61104 | 2.500 (0.0984) | K |
| 90564-61163 | 2.075 (0.0817) | AA | 90564-61172 | 2.525 (0.0994) | KK |
| 90564-61096 | 2.100 (0.0827) | B | 90564-61105 | 2.550 (0.100) | L |
| 90564-61164 | 2.125 (0.0837) | BB | 90564-61173 | 2.575 (0.101) | LL |
| 90564-61097 | 2.150 (0.0846) | C | 90564-61106 | 2.600 (0.102) | M |
| 90564-61165 | 2.175 (0.0856) | CC | 90564-61174 | 2.625 (0.103) | MM |
| 90564-61098 | 2.200 (0.0866) | D | 90564-61107 | 2.650 (0.104) | N |
| 90564-61166 | 2.225 (0.0876) | DD | 90564-61175 | 2.675 (0.105) | NN |
| 90564-61099 | 2.250 (0.0886) | E | 90564-61108 | 2.700 (0.106) | P |
| 90564-61167 | 2.275 (0.0896) | EE | 90564-61176 | 2.725 (0.107) | PP |
| 90564-61100 | 2.300 (0.0906) | F | 90564-61109 | 2.750 (0.108) | Q |
| 90564-61168 | 2.325 (0.0915) | FF | 90564-61177 | 2.775 (0.109) | |
| 90564-61101 | 2.350 (0.0925) | G | 90564-61110 | 2.800 (0.110) | R |
| 90564-61169 | 2.375 (0.0935) | GG | 90564-61178 | 2.825 (0.111) | RR |
| 90564-61102 | 2.400 (0.0945) | H | 90564-61111 | 2.850 (0.112) | S |
| 90564-61170 | 2.425 (0.0955) | HH | 90564-61179 | 2.875 (0.113) | SS |
| 90564-61103 | 2.450 (0.0965) | J | 90564-61112 | 2.900 (0.114) | T |
| 90564-61171 | 2.475 (0.0974) | JJ | - | - | - |
Select a thicker front differential case rear shim to increase the preload or a thinner front differential case rear shim to decrease the preload.
Make a memo as the torque values will be needed to adjust rear output shaft bearing preload.
Remove the 18 bolts and manual transmission case from the transaxle(MTM) case sub-assembly.
Remove the differential case assembly from the transaxle(MTM) case sub-assembly.
33134B
5.INSTALL OUTPUT SHAFT(MTM) COVER
| *a | Align the protrusion with the groove |
Install the output shaft(MTM) cover to the transaxle(MTM) case sub-assembly.
Align the protrusion of the output shaft(MTM) cover with the groove of the transaxle(MTM) case sub-assembly.
33321N
6.INSTALL FRONT OUTPUT SHAFT BEARING (OUTER RACE)
Using SST and a hammer, install a new front output shaft bearing (outer race) to the transaxle(MTM) case sub-assembly.
33321A
7.INSTALL REAR OUTPUT SHAFT BEARING (OUTER RACE)
Using SST and a hammer, install a new rear output shaft bearing (outer race) together with the rear output shaft bearing shim to the manual transmission case.
Use a rear output shaft bearing shim of the same thickness as the removed one.
8.ADJUST NO. 1 OUTPUT SHAFT BEARING PRELOAD
Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.
Coat the differential case assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.
Coat the output shaft assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.
Install the manual transmission case to the transaxle(MTM) case sub-assembly with the 18 bolts.
| *1 | Rear Output Shaft Bearing Shim |
Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.
Using SST and a torque wrench, measure the preload. Calculate the rear output shaft bearing preload using the following formula.
Measured preload - Differential side bearing preload = Output shaft bearing preload
1.72 to 4.74 N*m (18 to 48 kgf*cm, 16 to 41 in.*lbf)
1.72 to 4.74 N*m (18 to 48 kgf*cm, 16 to 41 in.*lbf)
If the preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.
| Part No. | Thickness mm (in.) | Mark | Part No. | Thickness mm (in.) | Mark |
|---|---|---|---|---|---|
| 90564-50294 | 1.600 (0.0630) | A | 90564-50313 | 2.075 (0.0817) | V |
| 90564-50295 | 1.625 (0.0640) | B | 90564-50314 | 2.100 (0.0827) | W |
| 90564-50296 | 1.650 (0.0650) | C | 90564-50315 | 2.125 (0.0837) | X |
| 90564-50297 | 1.675 (0.0659) | D | 90564-50316 | 2.150 (0.0846) | Y |
| 90564-50298 | 1.700 (0.0669) | E | 90564-50317 | 2.175 (0.0856) | Z |
| 90564-50299 | 1.725 (0.0679) | F | 90564-50318 | 2.200 (0.0866) | 1 |
| 90564-50300 | 1.750 (0.0689) | G | 90564-50319 | 2.225 (0.0876) | 2 |
| 90564-50301 | 1.775 (0.0699) | H | 90564-50320 | 2.250 (0.0886) | 3 |
| 90564-50302 | 1.800 (0.0709) | J | 90564-50321 | 2.275 (0.0896) | 4 |
| 90564-50303 | 1.825 (0.0719) | K | 90564-50322 | 2.300 (0.0906) | 5 |
| 90564-50304 | 1.850 (0.0728) | L | 90564-50323 | 2.325 (0.0915) | 6 |
| 90564-50305 | 1.875 (0.0738) | M | 90564-50324 | 2.350 (0.0925) | 7 |
| 90564-50306 | 1.900 (0.0748) | N | 90564-50325 | 2.375 (0.0935) | 8 |
| 90564-50307 | 1.925 (0.0758) | P | 90564-50326 | 2.400 (0.0945) | 9 |
| 90564-50308 | 1.950 (0.0768) | Q | 90564-50327 | 2.425 (0.0955) | 10 |
| 90564-50309 | 1.975 (0.0778) | R | 90564-50328 | 2.450 (0.0965) | 11 |
| 90564-50310 | 2.000 (0.0787) | S | 90564-50329 | 2.475 (0.0974) | 12 |
| 90564-50311 | 2.025 (0.0797) | T | 90564-50330 | 2.500 (0.0984) | 13 |
| 90564-50312 | 2.050 (0.0807) | U | - | - | - |
Select a thicker rear output shaft bearing shim to increase the preload or a thinner rear output shaft bearing shim to decrease the preload.
Remove the 18 bolts and manual transmission case from the transaxle(MTM) case sub-assembly.
Remove the output shaft assembly from the transaxle(MTM) case sub-assembly.
Remove the differential case assembly from the transaxle(MTM) case sub-assembly.
33253H
9.INSTALL OUTER SHIFT LEVER OIL SEAL
| *a | Depth |
Using SST and a hammer, install a new outer shift lever oil seal to the manual transmission case.
0.5 to 1.0 mm (0.0197 to 0.0394 in.)
Be sure to install the outer shift lever oil seal in the correct direction.
Coat the lip of the outer shift lever oil seal with MP grease.
33253
10.INSTALL OUTER NO. 1 SHIFT LEVER
| *1 | Outer No. 1 Shift Lever |
| *2 | Inner No. 1 Shift Lever |
Install the inner No. 1 shift lever and outer No. 1 shift lever to the manual transmission case.
Be sure to install the inner No. 1 shift lever in the correct direction.
| *a | Depth |
Using a 5 mm pin punch and hammer, install the inner shift lever slotted spring pin to the inner No. 1 shift lever.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
33124C
11.INSTALL NO. 1 OIL RECEIVER PIPE(MTM)
Engage the 2 guides and install the No. 1 oil receiver pipe(MTM) to the manual transmission case.
Make sure that the No. 1 oil receiver pipe(MTM) fully contacts the manual transmission case.
33137
12.INSTALL INPUT SHAFT(MTM) COVER
| *a | Align the protrusion with the groove |
Install the input shaft(MTM) cover to the manual transmission case.
Align the protrusion of the input shaft(MTM) cover with the groove of the manual transmission case.
33311K
13.INSTALL REAR INPUT SHAFT BEARING SHIM
Install the rear input shaft bearing shim to the manual transmission case.
The rear input shaft bearing shim should be cleaned before assembly.
Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension (A)).
| *1 | Manual Transmission Case | *2 | Input Shaft Assembly |
| *3 | Transaxle(MTM) Case Sub-assembly | - | - |
| *a | Dimension (A) | *b | Dimension (B) |
| *c | Dimension (C) | - | - |
Measure the distance between the end of the transaxle(MTM) case sub-assembly and installation surface of the front input shaft bearing (Dimension (B)).
Measure the distance between both input shaft bearing outer races (Dimension (C)).
Measure Dimension (C) with each bearing having no axial clearance.
Calculate the rear input shaft bearing shim value using the following formula.
(Dimension (A) + Dimension (B)) - Dimension (C) - Rear input shaft bearing shim thickness = 0.02 mm (0.000787 in.) to 0.14 mm (0.00551 in.)
If the clearance is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the clearance is within the specification.
| Part No. | Thickness mm (in.) | Mark | Part No. | Thickness mm (in.) | Mark |
|---|---|---|---|---|---|
| 90564-61116 | 1.30 (0.0512) | D | 90564-61122 | 1.60 (0.0630) | K |
| 90564-61117 | 1.35 (0.0531) | E | 90564-61123 | 1.65 (0.0650) | L |
| 90564-61118 | 1.40 (0.0551) | F | 90564-61124 | 1.70 (0.0669) | M |
| 90564-61119 | 1.45 (0.0571) | G | 90564-61125 | 1.75 (0.0689) | N |
| 90564-61120 | 1.50 (0.0591) | H | 90564-61126 | 1.80 (0.0709) | P |
| 90564-61121 | 1.55 (0.0610) | J | 90564-61162 | 1.85 (0.0728) | Q |
Coat the rear input shaft bearing shim with MP grease and install it to the manual transmission case.
Do not apply MP grease to the oil grooves.
33322H
14.INSTALL REAR REVERSE GEAR SHAFT BEARING SHIM
Install the rear reverse gear shaft bearing shim to the manual transmission case.
The rear reverse gear shaft bearing shim should be cleaned before assembly.
Measure the distance between the end of the manual transmission case and rear reverse gear shaft bearing shim (Dimension (A)).
| *1 | Manual Transmission Case | *2 | No. 2 Output Shaft Assembly |
| *3 | Transaxle(MTM) Case Sub-assembly | - | - |
| *a | Dimension (A) | *b | Dimension (B) |
| *c | Dimension (C) | - | - |
Measure the distance between the end of the transaxle(MTM) case sub-assembly and installation surface of the front reverse gear shaft bearing (Dimension (B)).
Measure the distance between both reverse gear shaft bearing outer races (Dimension (C)).
Measure Dimension (C) with each bearing having no axial clearance.
Calculate the rear reverse gear shaft bearing shim value using the following formula.
(Dimension (A) + Dimension (B)) - Dimension (C) - Rear reverse gear shaft bearing shim thickness = 0.10 mm (0.0039 in.) or less
If the clearance is not as specified, replace the rear reverse gear shaft bearing shim with one of a different thickness. Use the table below to select a rear reverse gear shaft bearing shim which will ensure that the clearance is within the specification.
| Part No. | Thickness mm (in.) | Mark | Part No. | Thickness mm (in.) | Mark |
|---|---|---|---|---|---|
| 90564-52078 | 1.90 (0.0748) | N | 90564-52085 | 2.25 (0.0886) | V |
| 90564-52079 | 1.95 (0.0768) | P | 90564-52086 | 2.30 (0.0906) | W |
| 90564-52080 | 2.00 (0.0787) | Q | 90564-52087 | 2.35 (0.0925) | X |
| 90564-52081 | 2.05 (0.0807) | R | 90564-52088 | 2.40 (0.0945) | Y |
| 90564-52082 | 2.10 (0.0827) | S | 90564-52089 | 2.45 (0.0965) | Z |
| 90564-52083 | 2.15 (0.0846) | T | 90564-52090 | 2.50 (0.0984) | 1 |
| 90564-52084 | 2.20 (0.0866) | U | - | - | - |
Coat the rear reverse gear shaft bearing shim with MP grease and install it to the manual transmission case.
31105D
15.INSTALL FRONT TRANSAXLE CASE OIL SEAL
| *a | Depth |
Using SST and a hammer, install a new front transaxle case oil seal to the transaxle(MTM) case sub-assembly.
0.9 to 1.9 mm (0.0354 to 0.0748 in.)
Be sure to install the front transaxle case oil seal in the correct direction.
Coat the lip of the front transaxle case oil seal with MP grease.
33257C
16.INSTALL OUTER SELECT LEVER OIL SEAL
| *a | Depth |
Using SST and a hammer, install a new outer select lever oil seal to the transaxle(MTM) case sub-assembly.
0.5 to 1.0 mm (0.0197 to 0.0394 in.)
Be sure to install the outer select lever oil seal in the correct direction.
Coat the lip of the outer select lever oil seal with MP grease.
33139G
17.INSTALL REVERSE GEAR SHAFT COVER
| *a | Align the protrusion with the groove |
Install the reverse gear shaft cover to the transaxle(MTM) case sub-assembly.
Align the protrusion of the reverse gear shaft cover with the groove of the transaxle(MTM) case sub-assembly.
33449B
18.INSTALL TRANSMISSION MAGNET
Clean the transmission magnet and install it to the transaxle(MTM) case sub-assembly.
33210
19.INSTALL NO. 1 GEAR SHIFT FORK ASSEMBLY
| *a | Depth |
Using a 5 mm pin punch and hammer, install the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft with the shift fork slotted pin.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Be sure to install the No. 1 gear shift fork assembly in the correct direction.
33232F
20.INSTALL NO. 1 GEAR SHIFT HEAD
| *a | Depth |
Using a 5 mm pin punch and hammer, install the No. 1 gear shift head to the No. 1 gear shift fork shaft with the shift head set slotted spring pin.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Be sure to install the No. 1 gear shift head in the correct direction.
21.INSTALL INPUT SHAFT ASSEMBLY
Apply gear oil to all sliding and rotating parts.
Coat the No. 1 fork shaft assembly with gear oil and install it to the output shaft assembly.
Coat the No. 2 gear shift fork assembly and No. 3 gear shift fork assembly with gear oil and install them to the input shaft assembly.
Temporarily install the input shaft assembly, output shaft assembly, No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly, and tie them with a rope or string.
Install the input shaft assembly together with the output shaft assembly, No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly to the transaxle(MTM) case sub-assembly.
33215B
22.INSTALL NO. 4 GEAR SHIFT FORK
Clean the bolt and installation hole in the No. 4 gear shift fork shaft.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.
Install the No. 4 gear shift fork to the No. 4 gear shift fork shaft with the bolt.
23.INSTALL DIFFERENTIAL CASE ASSEMBLY
Install the No. 4 fork shaft assembly to the No. 2 output shaft assembly.
Coat the differential case assembly, No. 2 output shaft assembly and No. 4 fork shaft assembly with gear oil and install them to the transaxle(MTM) case sub-assembly.
When installing the differential case assembly, the output shaft assembly may interfere. Therefore, slightly lift up the output shaft assembly.
33256
24.INSTALL INNER SELECT LEVER
Install the inner select lever to the transaxle(MTM) case sub-assembly.
Be sure to install the inner select lever in the correct direction.
25.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY
| *1 | Shift and Select Lever Shaft Assembly |
| *2 | Shift Inter Lock Plate |
| *3 | Inner Select Lever |
| *a | Position After Rotation |
Insert the shift and select lever shaft assembly into the transaxle (MTM) case sub-assembly and then rotate the shift and select lever shaft assembly clockwise to the position shown in the illustration to install it.
Make sure that the shift inter lock plate is engaged with the inner select lever after rotating the shift and select lever shaft assembly.
33257
26.INSTALL OUTER SELECT LEVER
Clean the bolt hole of the outer select lever.
Install the outer select lever to the transaxle(MTM) case sub-assembly and inner select lever.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the inner select lever set bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the inner select lever set bolt immediately after applying adhesive to prevent foreign matter from attaching to it.
Using a 6 mm hexagon socket wrench, install the inner select lever set bolt.
33111
27.INSTALL MANUAL TRANSMISSION CASE
Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.
| *a | FIPG
(Seal Diameter 1.2 mm (0.0472 in.)) |
Apply FIPG to the transaxle(MTM) case sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Remove any oil from the contact surfaces.
Install the parts within 10 minutes of application. Otherwise, the seal packing (FIPG) must be removed and reapplied.
| *a | Stopper |
Turn the outer No. 1 shift lever until it contacts the stopper of the manual transmission case and hold it in that position.
| *1 | Outer No. 1 Shift Lever |
| *2 | Inner No. 1 Shift Lever |
| *3 | Inner No. 2 Shift Lever |
| *a | Movement Inside Manual Transaxle Assembly |
While holding the outer No. 1 shift lever, set the manual transmission case onto the transaxle (MTM) case sub-assembly. Allow the outer No. 1 shift lever to rotate and install the manual transmission case to the transaxle (MTM) case sub-assembly.
Install the 18 bolts.
33275C
28.INSTALL SHIFT DETENT BALL
Clean the 2 shift detent ball plugs and 2 installation holes in the manual transmission case.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the ends of the 2 shift detent ball plugs.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the 2 shift detent ball plugs immediately after applying adhesive to prevent foreign matter from attaching to them.
| *1 | Shift Detent Ball Plug |
| *2 | Shift Detent Ball Compression Spring |
| *3 | Shift Detent Ball |
Install the 2 shift detent balls and 2 shift detent ball compression springs to the manual transmission case.
Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.
Be careful not to drop the shift detent balls into the manual transmission case.
Clean the shift detent ball plug and installation hole in the transaxle(MTM) case sub-assembly.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the shift detent ball plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the shift detent ball plug immediately after applying adhesive to prevent foreign matter from attaching to it.
| *1 | Shift Detent Ball Plug |
| *2 | No. 2 Shift Detent Ball Compression Spring |
| *3 | Shift Detent Ball |
Install the shift detent ball and No. 2 shift detent ball compression spring to the transaxle(MTM) case sub-assembly.
Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the transaxle(MTM) case sub-assembly.
Be careful not to drop the shift detent ball into the transaxle(MTM) case sub-assembly.
33292B
29.INSTALL NO. 2 LOCK BALL PIN
Clean the shift and select lever shaft straight screw with head plug and installation hole in the transaxle(MTM) case sub-assembly.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the shift and select lever shaft straight screw with head plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the shift and select lever shaft straight screw with head plug immediately after applying adhesive to prevent foreign matter from attaching to it.
| *1 | Shift and Select Lever Shaft Straight Screw with Head Plug |
| *2 | No. 1 Lock Ball Pin Return Spring |
| *3 | No. 2 Lock Ball Pin |
Install the No. 2 lock ball pin and No. 1 lock ball pin return spring to the transaxle(MTM) case sub-assembly.
Using a 10 mm hexagon socket wrench, install the shift and select lever shaft straight screw with head plug to the transaxle(MTM) case sub-assembly.
33292A
30.INSTALL LOCK BALL PIN
Clean the shift and select lever shaft straight screw with head plug and installation hole in the manual transmission case.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the shift and select lever shaft straight screw with head plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the shift and select lever shaft straight screw with head plug immediately after applying adhesive to prevent foreign matter from attaching to it.
| *1 | Shift and Select Lever Shaft Straight Screw with Head Plug |
| *2 | No. 2 Lock Ball Pin Return Spring |
| *3 | Lock Ball Pin |
Install the lock ball pin and No. 2 lock ball pin return spring to the manual transmission case.
Using a 10 mm hexagon socket wrench, install the shift and select lever shaft straight screw with head plug to the manual transmission case.
31482F
31.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE
31407B
32.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
31400
33.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY
34.INSTALL RELEASE CYLINDER BLEEDER PLUG
Install the release cylinder bleeder plug to the clutch release bleeder sub-assembly.
31478
35.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP
Install the release cylinder bleeder plug cap to the release cylinder bleeder plug.
89413B
36.INSTALL TRANSMISSION REVOLUTION SENSOR
84545
37.INSTALL NEUTRAL POSITION SWITCH
84210
38.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
33101B
39.INSTALL MANUAL TRANSMISSION DRAIN PLUG
Install a new gasket and the manual transmission drain plug to the manual transmission case.
33101A
40.INSTALL MANUAL TRANSMISSION FILLER PLUG
Install a new gasket and the manual transmission filler plug to the manual transmission case.
43420H
41.INSTALL FRONT DRIVE SHAFT OIL SEAL LH
43410M
42.INSTALL FRONT DRIVE SHAFT OIL SEAL RH
33101J
43.INSTALL BREATHER PLUG
Using SST and a hammer, install the breather plug to the transaxle(MTM) case sub-assembly.