Home › Drivetrain › EG62F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT
RM3620E _52 Drivetrain _076271 EG62F MANUAL TRANSMISSION / TRANSAXLE _0371330 MANUAL TRANSAXLE UNIT A

EG62F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 31105C 1.INSTALL TRANSAXLE CASE STRAIGHT PIN

a.
C402439C01
2.052,2.625 2.292,2.885 0.24,0.26 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, install 3 new transaxle case straight pins to the transaxle(MTM) case sub-assembly to the specified protrusion height.

Protrusion Height:

10.5 to 11.5 mm (0.413 to 0.453 in.)



Hide 41311E 2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C402440N01
2.49,1.656 3.01,1.656 false 2.458,2.01 2.729,2.01 2.729,2.01 2.729,1.656 false 3.052,1.573 3.417,1.792 0.365,0.219 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case sub-assembly.

SST
09316-20011  
09513-36040  

NOTICE:

Do not deform the front differential case front tapered roller bearing (inner race) cage.



b.
C407284C01
0.76,2.542 0.99,2.938 0.99,2.938 1.198,2.521 true 0.896,2.969 1.125,3.208 0.229,0.24 10 true *a
*a Align the protrusion with the groove


Install the front differential oil baffle to the transaxle(MTM) case sub-assembly.

NOTICE:
·

Align the protrusion of the front differential oil baffle with the groove of the transaxle(MTM) case sub-assembly.

·

Be sure to install the front differential oil baffle in the correct direction.




c.
C402441N01
1.938,2.802 1.219,2.563 1.219,2.563 2.104,2.5 true 0.865,2.479 1.208,2.719 0.344,0.24 10 true SST

Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle(MTM) case sub-assembly.

SST
09950-60021  (09951-00890)
09950-70010  (09951-07200)


Hide 41311F 3.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C402442N01
2.313,1.406 2.958,1.313 2.958,1.313 2.552,1.854 false 2.406,1.708 2.938,1.323 false 3,1.229 3.365,1.479 0.365,0.25 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case sub-assembly.

SST
09316-20011  
09950-60021  (09951-00770)
09950-70010  (09951-07100)

NOTICE:

Do not deform the front differential case rear tapered roller bearing (inner race) cage.



b.
C396339C01
2.177,3.031 2.677,3.031 false 1.792,2.417 2.583,2.417 true 1.542,1.865 1,1.25 1,1.25 1.646,1.323 true 2.708,2.917 3.021,3.073 0.313,0.156 10 false *a 2.625,2.333 3.083,2.531 0.458,0.198 10 false SST 0.708,1.156 1.167,1.354 0.458,0.198 10 false SST
*a Wooden Block


Using SST, a hammer and wooden block, install a new front differential case rear tapered roller bearing (outer race) together with the front differential case rear shim to the manual transmission case.

SST
09309-36010  
09950-60021  (09951-00890)
09950-70010  (09951-07200)

HINT:

Use a front differential case rear shim of the same thickness as the removed one.



Hide 4.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.


b.
C396340

Coat the differential case assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.


c.
C402419

Install the manual transmission case to the transaxle(MTM) case sub-assembly with the 18 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C402443C01
1.229,0.635 1.438,0.365 1.438,0.365 1.719,0.365 true 1.021,0.958 1.927,0.958 true 1.75,0.281 1.99,0.5 0.24,0.219 10 false *1 1.969,0.875 2.375,1.115 0.406,0.24 10 false SST
*1 Front Differential Case Rear Shim


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the preload.

SST
09564-33010  

Preload (at Starting):
New Bearing:

1.50 to 2.30 N*m (16 to 23 kgf*cm, 14 to 20 in.*lbf)

Used Bearing:

0.24 to 0.37 N*m (2.5 to 3.7 kgf*cm, 2.2 to 3.2 in.*lbf)


If the preload is not as specified, replace the front differential case rear shim with one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the preload is within the specification.

Front Differential Case Rear Shim Thickness:
Part No. Thickness mm (in.) Mark Part No. Thickness mm (in.) Mark
90564-61095 2.050 (0.0807) A 90564-61104 2.500 (0.0984) K
90564-61163 2.075 (0.0817) AA 90564-61172 2.525 (0.0994) KK
90564-61096 2.100 (0.0827) B 90564-61105 2.550 (0.100) L
90564-61164 2.125 (0.0837) BB 90564-61173 2.575 (0.101) LL
90564-61097 2.150 (0.0846) C 90564-61106 2.600 (0.102) M
90564-61165 2.175 (0.0856) CC 90564-61174 2.625 (0.103) MM
90564-61098 2.200 (0.0866) D 90564-61107 2.650 (0.104) N
90564-61166 2.225 (0.0876) DD 90564-61175 2.675 (0.105) NN
90564-61099 2.250 (0.0886) E 90564-61108 2.700 (0.106) P
90564-61167 2.275 (0.0896) EE 90564-61176 2.725 (0.107) PP
90564-61100 2.300 (0.0906) F 90564-61109 2.750 (0.108) Q
90564-61168 2.325 (0.0915) FF 90564-61177 2.775 (0.109) QQ
90564-61101 2.350 (0.0925) G 90564-61110 2.800 (0.110) R
90564-61169 2.375 (0.0935) GG 90564-61178 2.825 (0.111) RR
90564-61102 2.400 (0.0945) H 90564-61111 2.850 (0.112) S
90564-61170 2.425 (0.0955) HH 90564-61179 2.875 (0.113) SS
90564-61103 2.450 (0.0965) J 90564-61112 2.900 (0.114) T
90564-61171 2.475 (0.0974) JJ - - -


HINT:
·

Select a thicker front differential case rear shim to increase the preload or a thinner front differential case rear shim to decrease the preload.

·

Make a memo as the torque values will be needed to adjust rear output shaft bearing preload.




f.

Remove the 18 bolts and manual transmission case from the transaxle(MTM) case sub-assembly.


g.

Remove the differential case assembly from the transaxle(MTM) case sub-assembly.


Hide 33134B 5.INSTALL OUTPUT SHAFT(MTM) COVER

a.
C402433C03
0.948,0.656 1.313,0.844 true 0.813,0.542 1.01,0.719 0.198,0.177 10 true *a
*a Align the protrusion with the groove


Install the output shaft(MTM) cover to the transaxle(MTM) case sub-assembly.

NOTICE:

Align the protrusion of the output shaft(MTM) cover with the groove of the transaxle(MTM) case sub-assembly.



Hide 33321N 6.INSTALL FRONT OUTPUT SHAFT BEARING (OUTER RACE)

a.
C402444C01
1.5,2.198 0.458,1.448 0.458,1.448 1.563,1.885 true 0.125,1.375 0.458,1.625 0.333,0.25 10 false SST

Using SST and a hammer, install a new front output shaft bearing (outer race) to the transaxle(MTM) case sub-assembly.

SST
09950-70010  (09951-07200)
09951-00700  


Hide 33321A 7.INSTALL REAR OUTPUT SHAFT BEARING (OUTER RACE)

a.
C396343N01
1.219,1.813 0.406,2.135 0.406,2.135 1.344,1.333 true 0.104,2.042 0.563,2.24 0.458,0.198 10 false SST

Using SST and a hammer, install a new rear output shaft bearing (outer race) together with the rear output shaft bearing shim to the manual transmission case.

SST
09950-60011  (09951-00600)
09950-70010  (09951-07360)

HINT:

Use a rear output shaft bearing shim of the same thickness as the removed one.



Hide 8.ADJUST NO. 1 OUTPUT SHAFT BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.


b.
C396340

Coat the differential case assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.


c.
C396344

Coat the output shaft assembly with gear oil and install it to the transaxle(MTM) case sub-assembly.


d.
C402419

Install the manual transmission case to the transaxle(MTM) case sub-assembly with the 18 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


e.
C402445C01
1.01,0.396 1.281,0.396 1.281,0.396 1.563,0.25 true 0.438,1.25 0.604,1.25 0.604,1.25 0.917,1.823 true 0.813,0.323 1.021,0.552 0.208,0.229 10 false *1 0.125,1.188 0.448,1.427 0.323,0.24 10 false SST
*1 Rear Output Shaft Bearing Shim


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-33010  


f.

Using SST and a torque wrench, measure the preload. Calculate the rear output shaft bearing preload using the following formula.

SST
09564-33010  

Formula:

Measured preload - Differential side bearing preload = Output shaft bearing preload


Preload:
New Bearing:

1.72 to 4.74 N*m (18 to 48 kgf*cm, 16 to 41 in.*lbf)

Used Bearing:

1.72 to 4.74 N*m (18 to 48 kgf*cm, 16 to 41 in.*lbf)


If the preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.

Rear Output Shaft Bearing Shim Thickness:
Part No. Thickness mm (in.) Mark Part No. Thickness mm (in.) Mark
90564-50294 1.600 (0.0630) A 90564-50313 2.075 (0.0817) V
90564-50295 1.625 (0.0640) B 90564-50314 2.100 (0.0827) W
90564-50296 1.650 (0.0650) C 90564-50315 2.125 (0.0837) X
90564-50297 1.675 (0.0659) D 90564-50316 2.150 (0.0846) Y
90564-50298 1.700 (0.0669) E 90564-50317 2.175 (0.0856) Z
90564-50299 1.725 (0.0679) F 90564-50318 2.200 (0.0866) 1
90564-50300 1.750 (0.0689) G 90564-50319 2.225 (0.0876) 2
90564-50301 1.775 (0.0699) H 90564-50320 2.250 (0.0886) 3
90564-50302 1.800 (0.0709) J 90564-50321 2.275 (0.0896) 4
90564-50303 1.825 (0.0719) K 90564-50322 2.300 (0.0906) 5
90564-50304 1.850 (0.0728) L 90564-50323 2.325 (0.0915) 6
90564-50305 1.875 (0.0738) M 90564-50324 2.350 (0.0925) 7
90564-50306 1.900 (0.0748) N 90564-50325 2.375 (0.0935) 8
90564-50307 1.925 (0.0758) P 90564-50326 2.400 (0.0945) 9
90564-50308 1.950 (0.0768) Q 90564-50327 2.425 (0.0955) 10
90564-50309 1.975 (0.0778) R 90564-50328 2.450 (0.0965) 11
90564-50310 2.000 (0.0787) S 90564-50329 2.475 (0.0974) 12
90564-50311 2.025 (0.0797) T 90564-50330 2.500 (0.0984) 13
90564-50312 2.050 (0.0807) U - - -


HINT:

Select a thicker rear output shaft bearing shim to increase the preload or a thinner rear output shaft bearing shim to decrease the preload.



g.

Remove the 18 bolts and manual transmission case from the transaxle(MTM) case sub-assembly.


h.

Remove the output shaft assembly from the transaxle(MTM) case sub-assembly.


i.

Remove the differential case assembly from the transaxle(MTM) case sub-assembly.


Hide 33253H 9.INSTALL OUTER SHIFT LEVER OIL SEAL

a.
C396346C01
1.365,1.781 0.813,1.427 0.813,1.427 1.375,1.427 false 1.969,0.792 2.281,0.948 0.313,0.156 10 false *a 0.51,1.333 0.969,1.531 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install a new outer shift lever oil seal to the manual transmission case.

SST
09950-60011  (09951-00270)
09950-70010  (09951-07100)

Standard Depth:

0.5 to 1.0 mm (0.0197 to 0.0394 in.)


NOTICE:

Be sure to install the outer shift lever oil seal in the correct direction.



b.

Coat the lip of the outer shift lever oil seal with MP grease.


Hide 33253 10.INSTALL OUTER NO. 1 SHIFT LEVER

a.
C396328C01
0.583,1.24 1.042,1.24 false 1.583,1.208 1.99,1.208 true 0.427,1.146 0.74,1.302 0.313,0.156 10 false *1 2.031,1.094 2.25,1.281 0.219,0.188 10 true *2
*1 Outer No. 1 Shift Lever
*2 Inner No. 1 Shift Lever


Install the inner No. 1 shift lever and outer No. 1 shift lever to the manual transmission case.

NOTICE:

Be sure to install the inner No. 1 shift lever in the correct direction.



b.
C396347C01
0.208,2.125 0.521,2.281 0.313,0.156 10 false *a
*a Depth


Using a 5 mm pin punch and hammer, install the inner shift lever slotted spring pin to the inner No. 1 shift lever.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 33124C 11.INSTALL NO. 1 OIL RECEIVER PIPE(MTM)

a.
C396326

Engage the 2 guides and install the No. 1 oil receiver pipe(MTM) to the manual transmission case.

HINT:

Make sure that the No. 1 oil receiver pipe(MTM) fully contacts the manual transmission case.



Hide 33137 12.INSTALL INPUT SHAFT(MTM) COVER

a.
C396325C01
1.135,0.833 2.042,0.833 true 0.958,0.74 1.125,0.927 0.167,0.188 10 true *a
*a Align the protrusion with the groove


Install the input shaft(MTM) cover to the manual transmission case.

NOTICE:

Align the protrusion of the input shaft(MTM) cover with the groove of the manual transmission case.



Hide 33311K 13.INSTALL REAR INPUT SHAFT BEARING SHIM

a.
C396324

Install the rear input shaft bearing shim to the manual transmission case.

NOTICE:

The rear input shaft bearing shim should be cleaned before assembly.



b.

Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension (A)).

C402446C01
0.708,0.896 1.052,0.896 false 2.948,2.208 3.49,2.208 false 4.677,1.708 4.927,1.344 4.927,1.344 5.177,1.344 false 0.51,0.823 0.729,1.073 0.219,0.25 10 false *1 2.74,2.135 2.958,2.323 0.219,0.188 10 false *2 5.208,1.271 5.438,1.479 0.229,0.208 10 false *3 2.885,1.083 3.094,1.302 0.208,0.219 10 false *a 6.854,1.417 7.073,1.615 0.219,0.198 10 false *b 4.01,1.115 4.219,1.333 0.208,0.219 10 false *c
*1 Manual Transmission Case *2 Input Shaft Assembly
*3 Transaxle(MTM) Case Sub-assembly - -
*a Dimension (A) *b Dimension (B)
*c Dimension (C) - -



c.

Measure the distance between the end of the transaxle(MTM) case sub-assembly and installation surface of the front input shaft bearing (Dimension (B)).


d.

Measure the distance between both input shaft bearing outer races (Dimension (C)).

NOTICE:

Measure Dimension (C) with each bearing having no axial clearance.



e.

Calculate the rear input shaft bearing shim value using the following formula.

Formula:

(Dimension (A) + Dimension (B)) - Dimension (C) - Rear input shaft bearing shim thickness = 0.02 mm (0.000787 in.) to 0.14 mm (0.00551 in.)


If the clearance is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the clearance is within the specification.

Rear Input Shaft Bearing Shim Thickness:
Part No. Thickness mm (in.) Mark Part No. Thickness mm (in.) Mark
90564-61116 1.30 (0.0512) D 90564-61122 1.60 (0.0630) K
90564-61117 1.35 (0.0531) E 90564-61123 1.65 (0.0650) L
90564-61118 1.40 (0.0551) F 90564-61124 1.70 (0.0669) M
90564-61119 1.45 (0.0571) G 90564-61125 1.75 (0.0689) N
90564-61120 1.50 (0.0591) H 90564-61126 1.80 (0.0709) P
90564-61121 1.55 (0.0610) J 90564-61162 1.85 (0.0728) Q



f.

Coat the rear input shaft bearing shim with MP grease and install it to the manual transmission case.

NOTICE:

Do not apply MP grease to the oil grooves.



Hide 33322H 14.INSTALL REAR REVERSE GEAR SHAFT BEARING SHIM

a.
C396323

Install the rear reverse gear shaft bearing shim to the manual transmission case.

NOTICE:

The rear reverse gear shaft bearing shim should be cleaned before assembly.



b.

Measure the distance between the end of the manual transmission case and rear reverse gear shaft bearing shim (Dimension (A)).

C400540C01
0.865,0.854 1.615,0.854 false 4.719,1.802 5,1.406 false 2.948,2.417 3.229,2.021 false 0.708,0.76 1.021,0.917 0.313,0.156 10 false *1 2.792,2.344 3.104,2.5 0.313,0.156 10 false *2 5.021,1.292 5.333,1.448 0.313,0.156 10 false *3 2.75,1.198 3.063,1.354 0.313,0.156 10 false *a 3.865,1.656 4.177,1.813 0.313,0.156 10 false *c 6.844,1.5 7.156,1.656 0.313,0.156 10 false *b
*1 Manual Transmission Case *2 No. 2 Output Shaft Assembly
*3 Transaxle(MTM) Case Sub-assembly - -
*a Dimension (A) *b Dimension (B)
*c Dimension (C) - -



c.

Measure the distance between the end of the transaxle(MTM) case sub-assembly and installation surface of the front reverse gear shaft bearing (Dimension (B)).


d.

Measure the distance between both reverse gear shaft bearing outer races (Dimension (C)).

NOTICE:

Measure Dimension (C) with each bearing having no axial clearance.



e.

Calculate the rear reverse gear shaft bearing shim value using the following formula.

Formula:

(Dimension (A) + Dimension (B)) - Dimension (C) - Rear reverse gear shaft bearing shim thickness = 0.10 mm (0.0039 in.) or less


If the clearance is not as specified, replace the rear reverse gear shaft bearing shim with one of a different thickness. Use the table below to select a rear reverse gear shaft bearing shim which will ensure that the clearance is within the specification.

Rear Reverse Gear Shaft Bearing Shim Thickness:
Part No. Thickness mm (in.) Mark Part No. Thickness mm (in.) Mark
90564-52078 1.90 (0.0748) N 90564-52085 2.25 (0.0886) V
90564-52079 1.95 (0.0768) P 90564-52086 2.30 (0.0906) W
90564-52080 2.00 (0.0787) Q 90564-52087 2.35 (0.0925) X
90564-52081 2.05 (0.0807) R 90564-52088 2.40 (0.0945) Y
90564-52082 2.10 (0.0827) S 90564-52089 2.45 (0.0965) Z
90564-52083 2.15 (0.0846) T 90564-52090 2.50 (0.0984) 1
90564-52084 2.20 (0.0866) U - - -



f.

Coat the rear reverse gear shaft bearing shim with MP grease and install it to the manual transmission case.


Hide 31105D 15.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C402448C01
1.354,2.417 0.49,3.031 0.49,3.031 1.354,1.979 true 2.042,0.417 2.281,0.646 0.24,0.229 10 false *a 0.167,2.958 0.5,3.229 0.333,0.271 10 false SST
*a Depth


Using SST and a hammer, install a new front transaxle case oil seal to the transaxle(MTM) case sub-assembly.

SST
09950-60011  (09951-00350)
09950-70010  (09951-07150)

Standard Depth:

0.9 to 1.9 mm (0.0354 to 0.0748 in.)


NOTICE:

Be sure to install the front transaxle case oil seal in the correct direction.



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33257C 16.INSTALL OUTER SELECT LEVER OIL SEAL

a.
C402449C01
1.135,2.479 1.021,3.167 1.021,3.167 1.417,2.448 true 1.063,0.094 1.302,0.313 0.24,0.219 10 false *a 0.854,3.198 1.198,3.406 0.344,0.208 10 false SST
*a Depth


Using SST and a hammer, install a new outer select lever oil seal to the transaxle(MTM) case sub-assembly.

SST
09950-60011  (09951-00270)
09950-70010  (09951-07150)

Standard Depth:

0.5 to 1.0 mm (0.0197 to 0.0394 in.)


NOTICE:

Be sure to install the outer select lever oil seal in the correct direction.



b.

Coat the lip of the outer select lever oil seal with MP grease.


Hide 33139G 17.INSTALL REVERSE GEAR SHAFT COVER

a.
C402434C01
1.542,0.958 1.948,0.958 true 1.333,0.875 1.542,1.073 0.208,0.198 10 true *a
*a Align the protrusion with the groove


Install the reverse gear shaft cover to the transaxle(MTM) case sub-assembly.

NOTICE:

Align the protrusion of the reverse gear shaft cover with the groove of the transaxle(MTM) case sub-assembly.



Hide 33449B 18.INSTALL TRANSMISSION MAGNET

a.
C402430

Clean the transmission magnet and install it to the transaxle(MTM) case sub-assembly.


Hide 33210 19.INSTALL NO. 1 GEAR SHIFT FORK ASSEMBLY

a.
C401605C01
0.417,0.375 0.729,0.531 0.313,0.156 10 false *a
*a Depth


Using a 5 mm pin punch and hammer, install the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft with the shift fork slotted pin.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Be sure to install the No. 1 gear shift fork assembly in the correct direction.



Hide 33232F 20.INSTALL NO. 1 GEAR SHIFT HEAD

a.
C401606C01
0.76,1.208 1.073,1.365 0.313,0.156 10 false *a
*a Depth


Using a 5 mm pin punch and hammer, install the No. 1 gear shift head to the No. 1 gear shift fork shaft with the shift head set slotted spring pin.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Be sure to install the No. 1 gear shift head in the correct direction.



Hide 21.INSTALL INPUT SHAFT ASSEMBLY

a.

Apply gear oil to all sliding and rotating parts.


b.
C396353

Coat the No. 1 fork shaft assembly with gear oil and install it to the output shaft assembly.


c.
C396354

Coat the No. 2 gear shift fork assembly and No. 3 gear shift fork assembly with gear oil and install them to the input shaft assembly.


d.

Temporarily install the input shaft assembly, output shaft assembly, No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly, and tie them with a rope or string.


e.
C402451

Install the input shaft assembly together with the output shaft assembly, No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly to the transaxle(MTM) case sub-assembly.


Hide 33215B 22.INSTALL NO. 4 GEAR SHIFT FORK

a.

Clean the bolt and installation hole in the No. 4 gear shift fork shaft.


b.
P000601C54
1.958,1.573 1.667,1.833 false 1.583,1.854 1.833,2.094 0.25,0.24 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



c.
C396334

Install the No. 4 gear shift fork to the No. 4 gear shift fork shaft with the bolt.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 23.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C396351

Install the No. 4 fork shaft assembly to the No. 2 output shaft assembly.


b.
C402450

Coat the differential case assembly, No. 2 output shaft assembly and No. 4 fork shaft assembly with gear oil and install them to the transaxle(MTM) case sub-assembly.

HINT:

When installing the differential case assembly, the output shaft assembly may interfere. Therefore, slightly lift up the output shaft assembly.



Hide 33256 24.INSTALL INNER SELECT LEVER

a.
C396233

Install the inner select lever to the transaxle(MTM) case sub-assembly.

NOTICE:

Be sure to install the inner select lever in the correct direction.



Hide 25.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C402452C01
0.427,0.958 1.313,0.656 true 0.417,3.167 1.25,3.313 true 0.49,3.542 1.302,3.448 true 0.271,0.917 0.531,1.115 0.26,0.198 10 false *1 0.24,3.083 0.552,3.24 0.313,0.156 10 false *2 0.323,3.458 0.635,3.615 0.313,0.156 10 false *3 1.938,3.146 2.135,3.333 0.198,0.188 10 true *a
*1 Shift and Select Lever Shaft Assembly
*2 Shift Inter Lock Plate
*3 Inner Select Lever
*a Position After Rotation


Insert the shift and select lever shaft assembly into the transaxle (MTM) case sub-assembly and then rotate the shift and select lever shaft assembly clockwise to the position shown in the illustration to install it.

NOTICE:

Make sure that the shift inter lock plate is engaged with the inner select lever after rotating the shift and select lever shaft assembly.



Hide 33257 26.INSTALL OUTER SELECT LEVER

a.

Clean the bolt hole of the outer select lever.


b.
C402423

Install the outer select lever to the transaxle(MTM) case sub-assembly and inner select lever.


c.
P000601C54
1.958,1.573 1.667,1.833 false 1.583,1.854 1.833,2.094 0.25,0.24 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the inner select lever set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the inner select lever set bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



d.
C396230

Using a 6 mm hexagon socket wrench, install the inner select lever set bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 33111 27.INSTALL MANUAL TRANSMISSION CASE

a.

Remove any remaining seal packing from the contact surfaces of the transaxle(MTM) case sub-assembly and manual transmission case.


b.
C402453C01
2.281,0.656 2.458,0.344 2.458,0.344 2.719,0.344 true 2.75,0.271 3.063,0.427 0.313,0.156 10 false *a
*a FIPG
(Seal Diameter 1.2 mm (0.0472 in.))


Apply FIPG to the transaxle(MTM) case sub-assembly as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the parts within 10 minutes of application. Otherwise, the seal packing (FIPG) must be removed and reapplied.




c.
C396358C01
0.448,1.552 1.094,0.958 true 0.271,1.469 0.583,1.625 0.313,0.156 10 false *a
*a Stopper


Turn the outer No. 1 shift lever until it contacts the stopper of the manual transmission case and hold it in that position.


d.
C402454C01
0.615,1.438 0.885,1.438 0.885,1.438 1.385,2.323 true 2.292,0.813 2.635,0.813 true 1.719,1.406 2.271,1.781 true 0.479,1.365 0.792,1.521 0.313,0.156 10 false *1 2.135,0.719 2.448,0.875 0.313,0.156 10 false *2 1.563,1.302 1.875,1.458 0.313,0.156 10 false *3 1.948,0.135 2.25,0.333 0.302,0.198 10 false *a
*1 Outer No. 1 Shift Lever
*2 Inner No. 1 Shift Lever
*3 Inner No. 2 Shift Lever
*a Movement Inside Manual Transaxle Assembly


While holding the outer No. 1 shift lever, set the manual transmission case onto the transaxle (MTM) case sub-assembly. Allow the outer No. 1 shift lever to rotate and install the manual transmission case to the transaxle (MTM) case sub-assembly.


e.
C402419

Install the 18 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33275C 28.INSTALL SHIFT DETENT BALL

a.

Clean the 2 shift detent ball plugs and 2 installation holes in the manual transmission case.


b.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 2 shift detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 2 shift detent ball plugs immediately after applying adhesive to prevent foreign matter from attaching to them.



c.
C396226C01
0.26,1.5 0.26,1.313 true 0.531,1.479 0.531,1.292 true 0.896,1.479 0.771,1.26 true 2.406,0.854 2.406,0.667 true 2.719,0.865 2.719,0.615 true 3.063,0.854 2.948,0.625 true 0.188,1.5 0.396,1.646 0.208,0.146 10 true *1 2.656,0.865 2.969,1.021 0.313,0.156 10 false *2 0.854,1.51 1.167,1.667 0.313,0.156 10 false *3 0.49,1.51 0.802,1.667 0.313,0.156 10 false *2 2.344,0.854 2.552,1 0.208,0.146 10 false *1 3.021,0.865 3.333,1.021 0.313,0.156 10 false *3
*1 Shift Detent Ball Plug
*2 Shift Detent Ball Compression Spring
*3 Shift Detent Ball


Install the 2 shift detent balls and 2 shift detent ball compression springs to the manual transmission case.


d.

Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Be careful not to drop the shift detent balls into the manual transmission case.



e.

Clean the shift detent ball plug and installation hole in the transaxle(MTM) case sub-assembly.


f.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the shift detent ball plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the shift detent ball plug immediately after applying adhesive to prevent foreign matter from attaching to it.



g.
C396225C01
0.26,1.063 0.26,0.729 true 0.688,1.052 0.688,0.708 true 1.167,1.073 1.167,0.708 true 0.219,1.083 0.531,1.24 0.313,0.156 10 false *1 0.625,1.094 0.938,1.25 0.313,0.156 10 false *2 1.104,1.094 1.417,1.25 0.313,0.156 10 false *3
*1 Shift Detent Ball Plug
*2 No. 2 Shift Detent Ball Compression Spring
*3 Shift Detent Ball


Install the shift detent ball and No. 2 shift detent ball compression spring to the transaxle(MTM) case sub-assembly.


h.

Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the transaxle(MTM) case sub-assembly.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Be careful not to drop the shift detent ball into the transaxle(MTM) case sub-assembly.



Hide 33292B 29.INSTALL NO. 2 LOCK BALL PIN

a.

Clean the shift and select lever shaft straight screw with head plug and installation hole in the transaxle(MTM) case sub-assembly.


b.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the shift and select lever shaft straight screw with head plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the shift and select lever shaft straight screw with head plug immediately after applying adhesive to prevent foreign matter from attaching to it.



c.
C396224C01
0.208,1.396 0.208,1.156 true 0.552,1.427 0.552,1.042 true 1.073,1.406 0.885,1.063 true 0.167,1.406 0.479,1.563 0.313,0.156 10 false *1 0.5,1.427 0.813,1.583 0.313,0.156 10 false *2 1.021,1.417 1.333,1.573 0.313,0.156 10 false *3
*1 Shift and Select Lever Shaft Straight Screw with Head Plug
*2 No. 1 Lock Ball Pin Return Spring
*3 No. 2 Lock Ball Pin


Install the No. 2 lock ball pin and No. 1 lock ball pin return spring to the transaxle(MTM) case sub-assembly.


d.

Using a 10 mm hexagon socket wrench, install the shift and select lever shaft straight screw with head plug to the transaxle(MTM) case sub-assembly.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33292A 30.INSTALL LOCK BALL PIN

a.

Clean the shift and select lever shaft straight screw with head plug and installation hole in the manual transmission case.


b.
C324918C01
1.792,1.208 1.958,0.5 1.958,0.5 2.104,0.5 false 2.146,0.417 2.458,0.573 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the shift and select lever shaft straight screw with head plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the shift and select lever shaft straight screw with head plug immediately after applying adhesive to prevent foreign matter from attaching to it.



c.
C396223C01
0.188,1.031 0.188,0.813 true 0.427,1.021 0.427,0.729 true 1.021,1.135 0.698,0.75 true 0.115,1.052 0.427,1.208 0.313,0.156 10 false *1 0.365,1.052 0.677,1.208 0.313,0.156 10 false *2 1.052,1.052 1.365,1.208 0.313,0.156 10 false *3
*1 Shift and Select Lever Shaft Straight Screw with Head Plug
*2 No. 2 Lock Ball Pin Return Spring
*3 Lock Ball Pin


Install the lock ball pin and No. 2 lock ball pin return spring to the manual transmission case.


d.

Using a 10 mm hexagon socket wrench, install the shift and select lever shaft straight screw with head plug to the manual transmission case.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 31482F 31.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE

Hide 31407B 32.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 33.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 34.INSTALL RELEASE CYLINDER BLEEDER PLUG

a.
C396222

Install the release cylinder bleeder plug to the clutch release bleeder sub-assembly.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 31478 35.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP

a.
C396221

Install the release cylinder bleeder plug cap to the release cylinder bleeder plug.


Hide 89413B 36.INSTALL TRANSMISSION REVOLUTION SENSOR

Hide 84210 38.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

Hide 33101B 39.INSTALL MANUAL TRANSMISSION DRAIN PLUG

a.
C396217

Install a new gasket and the manual transmission drain plug to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33101A 40.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C396216

Install a new gasket and the manual transmission filler plug to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33101J 43.INSTALL BREATHER PLUG

a.
C402457N01
1.729,0.542 2.542,0.542 true 1.385,0.469 1.74,0.698 0.354,0.229 10 false SST

Using SST and a hammer, install the breather plug to the transaxle(MTM) case sub-assembly.

SST
09350-30020  (09350-07110)