The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
33185B
1.INSTALL TRANSAXLE UNDER STOPPER BRACKET
|
Bolt A |
|
Bolt B |
|
Bolt C |
Install the transaxle under stopper bracket to the hybrid vehicle transaxle assembly with the 4 bolts.
Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)
2.INSTALL STUD BOLT
Clean and degrease the bolt holes of the hybrid vehicle transaxle assembly.
Apply adhesive to 2 or 3 threads on the ends of the 2 stud bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
In order to ensure proper installation of the 2 stud bolts, apply adhesive to the 2 stud bolts and install them within 10 minutes of adhesive application.
Using an E8 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.
3.INSTALL TRANSAXLE HOUSING PLUG
Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.
4.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 4 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 4 bolts.
|
Bolt A |
|
Bolt B |
82125
5.INSTALL TRANSMISSION WIRE
Install the transmission wire to the hybrid vehicle transaxle assembly with the bolt.
Connect the connector.
44781E
6.INSTALL HOSE BRACKET
Temporarily install the hose bracket to the hybrid vehicle transaxle assembly with the 2 bolts.
Tighten the 2 bolts in the order shown in the illustration.
33823
7.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.
G125A
8.INSTALL MOTOR COOLING COOLER
G1148
9.INSTALL MOTOR CABLE
30900
10.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
|
Knock Pin |
Make sure that the knock pins are installed to the engine assembly.
|
Bolt A |
Align the knock pins with the holes in the hybrid transaxle assembly and, while keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, temporarily install the bolt (A).
When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.
Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not use excessive force when installing the hybrid vehicle transaxle assembly.
Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.
When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.
When installing the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock pin holes.
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
While keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, install the 8 bolts.
| Bolt | Bolt Length |
|---|---|
| A and B | 50 mm (1.97 in.) |
| C | 45 mm (1.77 in.) |
| D | 35 mm (1.38 in.) |
12303
11.INSTALL REAR ENGINE MOUNTING BRACKET
|
Bolt A |
|
Bolt B |
|
Bolt C |
Install the rear engine mounting bracket to the hybrid vehicle transaxle assembly with the 4 bolts.
Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A) → Tighten bolt (C)
12.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the rear engine mounting insulator with the bolt.
12371A
13.INSTALL REAR ENGINE MOUNTING INSULATOR
12311A
14.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
|
Bolt A |
|
Bolt B |
|
Bolt C |
Install the transverse engine engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.
Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)
12361
15.INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the front engine mounting insulator to the transverse engine engine mounting bracket with the bolt.
51100H
16.INSTALL FRONT FRAME ASSEMBLY
11363A
17.INSTALL FLYWHEEL HOUSING SIDE COVER
Install the flywheel housing side cover to the engine assembly.
28193
18.INSTALL STARTER HOLE INSULATOR
Install the starter hole insulator to the engine assembly with the 2 bolts.
821H2
19.CONNECT HV AIR CONDITIONING WIRE
Attach the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.
Install the bolt.
82121
20.CONNECT ENGINE WIRE (for LHD)
Connect the 5 clamps.
|
Bolt A |
|
Bolt B |
Install the 2 bolts.
82121
21.CONNECT ENGINE WIRE (for RHD)
Connect the 4 clamps.
|
Bolt A |
|
Bolt B |
Install the 2 bolts.
22.CONNECT WIRE HARNESS (for RHD)
23.CONNECT WIRE HARNESS (for LHD)
45319
24.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)
25.REMOVE ENGINE HANGERS
23825
26.INSTALL FUEL DELIVERY GUARD
27.INSTALL ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSAXLE ASSEMBLY
28. PERFORM RESOLVER LEARNING
If the hybrid vehicle transaxle assembly has been replaced, make sure to perform resolver learning.