Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › 2018.10–2019.02
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371339 OIL COOLER A

P710 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cooling cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Reset back door close position Power door lock control system (Click here)
ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 53896B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 3.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 6.REMOVE FRONT FENDER APRON SEAL LH

Hide G9225K 7.REMOVE NO. 1 INVERTER COOLING HOSE

a.
C393920

Slide the clip and remove the No. 1 inverter cooling hose from the motor cooling cooler.


Hide G9229A 8.DISCONNECT NO. 5 INVERTER COOLING HOSE

Hide G125A 9.REMOVE MOTOR COOLING COOLER

a.
C393921C01
1.771,0.323 1.917,0.323 1.917,0.323 2.083,0.563 true 1,0.594 1.146,0.594 1.146,0.594 1.313,0.833 true 1.573,0.25 1.781,0.427 0.208,0.177 10 true *1 0.771,0.521 1,0.698 0.229,0.177 10 true *2
*1 Oil Cooler Union Bolt
*2 No. 1 Oil Cooler Tube Clamp


Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


b.

Remove the bolt and No. 1 oil cooler tube clamp to disconnect No. 2 motor cooling pipe from the hose bracket.


c.
C393922

Remove the 3 bolts to disconnect the motor cooling cooler from the No. 1 transmission control cable bracket.

HINT:

Use a container to catch any coolant and hybrid transaxle fluid which flow out of the motor cooling cooler.



d.
C393923

Slide the clip and disconnect the No. 1 motor cooling hose from the transaxle housing tube connector.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1252A 10.REMOVE NO. 2 MOTOR COOLING PIPE

a.
C393924

Slide the clip and remove the No. 2 motor cooling pipe from the No. 2 motor cooling hose.

NOTICE:

Make sure not to remove the No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.