Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION ECU › 2018.10–2020.08
RM3620E _56 Audio / Visual / Telematics _076048 NAVIGATION / MULTI INFO DISPLAY _0370118 NAVIGATION ECU A

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION ECU  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly or navigation ECU may not operate normally.


·

When performing the following work, the navigation system may restart when turning the ignition switch ACC (due to radio and display receiver assembly and navigation ECU certification).

-

Repair or replace the negative (-) auxiliary battery terminal due to it being disconnected or depleted.

-

The radio and display receiver assembly or navigation ECU replacement or removal and installation.



Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


Hide 55900 3.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 55434B 4.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 5.REMOVE NAVIGATION ECU WITH BRACKET

a.

w/ Telematics Transceiver:

i.
E406834C02
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E406835C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, detach the guide and remove the navigation ECU with bracket.


iv.

Disconnect each connector.

HINT:

Remove the navigation ECU with bracket together with the No. 2 navigation wire and No. 2 antenna cord sub-assembly.




b.

w/o Telematics Transceiver:

i.
E406842C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E406843C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, detach the guide and remove the navigation ECU with bracket.


iv.

Disconnect each connector.

HINT:

Remove the navigation ECU with bracket together with the No. 2 navigation wire.




Hide 86101J 6.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/ Telematics Transceiver:

i.
E406836

Disconnect the 3 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



b.

w/o Telematics Transceiver:

i.
E406844

except Korea:

1.

Disconnect the connector.

2.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



ii.
E406848

for Korea:

1.

Disconnect the 2 connectors.

2.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.




Hide 86101J 7.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

w/ Telematics Transceiver:

i.
E406854

Disconnect the 3 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



b.

w/o Telematics Transceiver:

i.
E406856

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



Hide 86842J 8.REMOVE NO. 2 NAVIGATION WIRE (for LHD)

a.

w/ Telematics Transceiver:

i.
E406837

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 navigation wire.



b.

w/o Telematics Transceiver:

i.
E406845

except Korea:

1.

Disconnect the connector.

2.

Detach the clamp and remove the No. 2 navigation wire.



ii.
E406849

for Korea:

1.

Disconnect the connector.

2.

Detach the clamp and remove the No. 2 navigation wire.




Hide 86842J 9.REMOVE NO. 2 NAVIGATION WIRE (for RHD)

a.

w/ Telematics Transceiver:

i.
E406855

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 navigation wire.



b.

w/o Telematics Transceiver:

i.
E406857

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 navigation wire.



Hide 86457 10.REMOVE NO. 1 MULTI-MEDIA MODULE BRACKET

a.
E406838

w/ Telematics Transceiver:

Remove the 3 screws and No. 1 multi-media module bracket.


b.
E406846

w/o Telematics Transceiver:

Remove the 2 screws and No. 1 multi-media module bracket.


Hide 86457A 11.REMOVE NO. 2 MULTI-MEDIA MODULE BRACKET

a.
E406839

w/ Telematics Transceiver:

Remove the 3 screws and No. 2 multi-media module bracket.


b.
E406847

w/o Telematics Transceiver:

Remove the 2 screws and No. 2 multi-media module bracket.


Hide 86841 12.REMOVE NAVIGATION ECU