Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076053 INTERIOR PANELS / TRIM _0370160 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel safety pad assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. TABLE OF BOLT, SCREW, NUT AND CLIP

HINT:

All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.


B523297E01
0.146,0.24 0.76,0.438 0.615,0.198 10 false Code 2.448,0.24 3.063,0.438 0.615,0.198 10 false Code 4.792,0.24 5.406,0.438 0.615,0.198 10 false Code 1.26,0.26 2.031,0.458 0.771,0.198 10 false Shape 3.542,0.25 4.313,0.448 0.771,0.198 10 false Shape 5.875,0.25 6.646,0.448 0.771,0.198 10 false Shape 0.177,0.948 0.635,1.146 0.458,0.198 10 false <A> 2.49,0.958 2.948,1.156 0.458,0.198 10 false <B> 4.833,0.979 5.292,1.177 0.458,0.198 10 false <C> 0.177,1.896 0.635,2.094 0.458,0.198 10 false <D> 5.802,2.396 7.104,2.781 1.302,0.385 10 false mm (in.) (L=Length) 1.948,0.708 2.26,0.906 0.313,0.198 10 false φ 5 1.938,0.875 3.01,1.073 1.073,0.198 10 false (0.197) 1.969,1.063 2.396,1.292 0.427,0.229 10 false L=14 1.938,1.229 2.438,1.458 0.5,0.229 10 false (0.551) 4.281,0.698 4.594,0.896 0.313,0.198 10 false φ 6 4.292,1.073 4.688,1.302 0.396,0.229 10 false L=20 4.292,1.802 4.604,2 0.313,0.198 10 false φ 6 4.271,2 5.344,2.198 1.073,0.198 10 false (0.236) 4.26,0.865 5.333,1.063 1.073,0.198 10 false (0.236) 4.271,1.24 4.833,1.49 0.563,0.25 10 false (0.787) 6.563,0.729 6.875,0.927 0.313,0.198 10 false φ 8 6.552,0.906 7.115,1.219 0.563,0.313 10 false (0.315) 6.573,1.104 6.969,1.333 0.396,0.229 10 false L=21 6.563,1.26 7.125,1.51 0.563,0.25 10 false (0.827) 2.51,1.906 2.969,2.104 0.458,0.198 10 false <E>

Hide 2. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 5.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 55405B 8.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Type A)

a.
B523291C02
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and claw and remove the center instrument cluster finish panel sub-assembly.


Hide 55424C 9.REMOVE RADIO TUNER FINISH PANEL (for Type A, w/ Radio Receiver Opening Cover)

a.
B529071C02
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the radio tuner finish panel.


Hide 55422C 10.REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

a.
B523292C02
0,0 0,0 false
V113147

Remove in this Direction


for Type A:

Using moulding remover B, detach the clip and remove the center upper instrument cluster finish panel.


b.

for Type B:

i.
B523205C01
0,0 0,0 false
V113147

Remove in this Direction


Using moulding remover B, detach the clip.


ii.
B523267C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Using moulding remover B, detach the clip as shown in the illustration and remove the center upper instrument cluster finish panel.



Hide 11.REMOVE STEREO OPENING COVER WITH BRACKET (for Type A, w/ Cover)

a.
B529069

Remove the 4 bolts.


b.
B557515C04
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the stereo opening cover with bracket.


Hide 12.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 13.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 55474B 14.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B523199C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and guide and remove the instrument cluster finish panel garnish.


Hide 55410C 15.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B523201C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and detach the claw and guide as shown in the illustration.


b.
B523202C01
0,0 0,0 false
V113147

Remove in this Direction


Pull towards the rear of the vehicle to detach the clip and remove the instrument cluster finish panel assembly.


Hide 83100 16.REMOVE COMBINATION METER ASSEMBLY

Hide 55900 17.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 55434B 18.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

a.
B523206C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the lower center instrument panel finish panel assembly.


b.

Disconnect each connector.


Hide 67914B 19.REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)

Hide 62112 20.REMOVE COWL SIDE TRIM BOARD LH (for LHD)

a.
B523208

Remove the cap nut.


b.
B523209C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and guide and remove the cowl side trim board LH.


Hide 55606 21.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

a.
B523210C02
0,0 0,0 false
V100135

Screw <A>


Remove the 3 screws <A>.


b.
B523211C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and guide and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.


c.

w/ Foot Light:

i.
B523212

Disconnect the connector and detach the clamp.


ii.

Detach the claw and remove the DLC3.



d.

w/o Foot Light:

i.
B531218

Detach the claw and remove the DLC3.

HINT:

Even if there is no foot light, if there is a connector, disconnect the connector and detach the clamp.




e.
B523213C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 1 instrument panel under cover sub-assembly.


Hide 62312B 22.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B523214

Remove the front door opening trim weatherstrip LH from the area shown in the illustration.


Hide 55318C 23.REMOVE INSTRUMENT SIDE PANEL LH

a.
B523215C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


b.
B523216C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel LH.


c.

for RHD, w/ Airbag Cut Off Switch:

Disconnect the connector.


Hide 53601 24.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B529075C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the claw in the direction (1) indicated by the arrow shown in the illustration.


b.

Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the hood lock control lever sub-assembly.


Hide 77306 25.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Gasoline Model)

a.
B529076C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the claw in the direction (1) indicated by the arrow shown in the illustration.


b.

Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the fuel lid lock open lever sub-assembly.


Hide 55545 26.REMOVE FUSE BOX OPENING COVER (for LHD)

a.
B523217C01
0,0 0,0 false
V100135

Bolt <B>


Remove the bolt <B>.


b.
B523218C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction indicated by the arrow to detach the clip.


c.
B523219C01
0.052,0.052 0.427,0.292 0.375,0.24 12 false *A 0.052,2.521 0.427,2.76 0.375,0.24 12 false *B
*A for 6 Switch Type
*B for 3 Switch Type


Disconnect each connector.


d.

Detach the clamp and remove the fuse box opening cover.


e.

for HV Model:

Disconnect the connector.


Hide 55545 27.REMOVE FUSE BOX OPENING COVER (for RHD)

a.
B529079C01
0,0 0,0 false
V100135

Bolt <B>


Remove the bolt <B>.


b.
B529080C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction indicated by the arrow to detach the clip and remove the fuse box opening cover.


c.
B529081

Disconnect each connector.


d.

for HV Model:

Disconnect the connector.


Hide 55480D 28.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B523222C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the lower instrument panel finish panel assembly.


b.

w/ Entry and Start System:

Disconnect the connector.


Hide 73900 29.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 62212 30.REMOVE FRONT PILLAR GARNISH LH

Hide 55525 31.REMOVE NO. 1 SPEAKER HOLE COVER

a.
B523223C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Lift up the part in the removal direction shown in the illustration to detach the clip.


b.
B523224C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 1 speaker hole cover.


Hide 86160P 32.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)

Hide 62311B 33.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B523266

Remove the front door opening trim weatherstrip RH from the area shown in the illustration.


Hide 67913B 34.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111C 35.REMOVE COWL SIDE TRIM BOARD RH

a.
B529096

Remove the cap nut.


b.
B529097C02
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and guide and remove the cowl side trim board RH.


Hide 55607 36.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B523225C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and lower the No. 2 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.


b.
B523226

w/ Foot Light:

Disconnect the connector and detach the clamp.

HINT:
B531219

Even if there is no foot light, if there is a connector, disconnect the connector and detach the clamp.



c.
B523227C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel under cover sub-assembly.


Hide 55550 37.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B529115C02
2.958,0.781 2.813,0.573 true 3.125,2.99 2.979,2.781 true 3.031,2.938 3.281,3.135 0.25,0.198 10 true *1 3.01,0.729 3.25,0.938 0.24,0.208 10 true *a 0.302,0.844 0.469,1.052 0.167,0.208 10 true A 2.948,1.271 3.115,1.469 0.167,0.198 10 true B
*1 Glove Compartment Door Stopper Sub-assembly
*a Stopper
V113147

Remove in this Direction


Detach the claw and remove the glove compartment door stopper sub-assembly.


b.

Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and open the glove compartment door assembly until the stoppers are released.


c.
B529140C01
0.531,0.104 0.844,0.26 0.313,0.156 10 false *a 2.042,0.073 2.354,0.229 0.313,0.156 10 false *b
*a Closed Position
*b Assembly Position
V113147

Remove in this Direction


Assembly position the glove compartment door assembly, pull it horizontally in the direction indicated by the arrow to detach the hinge and remove the glove compartment door assembly.

NOTICE:

Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.



Hide 55433B 38.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B523228C02
0,0 0,0 false
V100135

Bolt <B>
V100136

Screw <A>


Remove the 3 screws <A> and 2 bolts <B>.


b.
B523229C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the lower No. 2 instrument panel finish panel.


Hide 55475A 39.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B523230C01
3.115,3.656 3.323,3.865 0.208,0.208 10 true (1) 2.74,3.865 2.948,4.115 0.208,0.25 10 true (2) 2.438,3.323 2.646,3.521 0.208,0.198 10 true (3) 1.75,3.521 1.979,3.75 0.229,0.229 10 true (4) 1.531,3.344 1.75,3.542 0.219,0.198 10 true (5) 1.188,3.313 1.406,3.521 0.219,0.208 10 true (6) 0.688,3.292 0.885,3.49 0.198,0.198 10 true (7) 0.208,3.219 0.427,3.438 0.219,0.219 10 true (8)
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand in the gap, and then, while pulling in the direction indicated by the arrow shown in the illustration, detach the clip in the order shown in the illustration and remove the No. 2 instrument cluster finish panel garnish.


Hide 55317A 40.REMOVE INSTRUMENT SIDE PANEL RH

a.
B523231C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


b.
B523232C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel RH.


c.

for LHD, w/ Airbag Cut Off Switch:

Disconnect the connector.


Hide 62211 41.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 55535B 42.REMOVE NO. 2 SPEAKER HOLE COVER

a.
B523233C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Lift up the part in the removal direction shown in the illustration to detach the clip.


b.
B523234C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 2 speaker hole cover.


Hide 86160P 43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)

HINT:

Use the same procedure described for the other side.


Hide 86160L 44.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for eCall)

Hide 84330 45.REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

Hide 45287 46.REMOVE LOWER STEERING COLUMN COVER

Hide 47.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)

a.

Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.


B529118C02
1.24,2.729 1.74,2.375 true 4.948,2.74 5.448,2.385 true 1.083,2.698 1.396,2.896 0.313,0.198 10 false *a 4.823,2.708 5.135,2.906 0.313,0.198 10 false *a 0.292,1.958 0.667,2.198 0.375,0.24 12 false *A 3.604,1.99 3.979,2.229 0.375,0.24 12 false *B
*A for Dual Type *B for Single Type
*a Lock Slider - -
V113147

Slide in this Direction - -



b.
B523235

Disconnect the connector and detach the guide.


c.
B523269C01
0,0 0,0 false
V100135

Bolt <C>


Remove the 2 bolts <C>.


d.
B523265

Disconnect each connector.


e.
B523237

w/ Interior Illumination:

Disconnect the connector.


f.
B523236

Remove the 2 nuts and steering column assembly from the instrument panel reinforcement assembly.


g.
B523270

for Automatic Air Conditioning System:

Detach the claw and remove the cooler (room temp. sensor) thermistor.


h.

Detach the clamp.


i.

Remove the 2 clips <D>.


j.

Remove the 5 bolts <B> and nut <E>.

B523238C01
0,0 0,0 false
V100135

Bolt <B>
V100136

Nut <E>
V100137

Clip <D> - -



k.

Pull in the direction indicated by the arrow shown in the illustration and detach the guide and remove the instrument panel safety pad assembly.

B523239C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 48.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)

a.

Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.


B529120C01
3.198,2.708 3.719,2.385 true 3.063,2.677 3.375,2.875 0.313,0.198 10 false *a
*a Lock Slider - -
V113147

Slide in this Direction - -



b.
B529087

Disconnect the connector and detach the guide.


c.
B529088C01
0,0 0,0 false
V100135

Bolt <C>


Remove the 2 bolts <C>.


d.
B529089

Disconnect each connector.


e.
B529090

w/ Interior Illumination:

Disconnect the connector.


f.
B529091

Remove the 2 nuts and steering column assembly from the instrument panel reinforcement assembly.


g.
B529092

for Automatic Air Conditioning System:

Detach the claw and remove the cooler (room temp. sensor) thermistor.


h.

Detach the clamp.


i.

Remove the 2 clips <D>.


j.

Remove the 5 bolts <B> and nut <E>.

B529093C01
0,0 0,0 false
V100135

Bolt <B>
V100136

Nut <E>
V100137

Clip <D> - -



k.

Pull in the direction indicated by the arrow shown in the illustration and detach the guide and remove the instrument panel safety pad assembly.

B529094C01
0,0 0,0 false
V113147

Remove in this Direction - -