Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY VOLTAGE SENSOR (for NICKEL METAL HYDRIDE BATTERY) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371634 BATTERY VOLTAGE SENSOR(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR(for NICKEL METAL HYDRIDE BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedures not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of HV battery Battery status info update HV battery status information cannot be updated (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

The type of battery voltage sensor to be used varies depending on the vehicle model.

·
A401803C01
2.052,0.823 2.958,0.823 true 2.979,0.719 3.292,0.875 0.313,0.156 10 false *a
*a Blue Label


The type of battery voltage sensor can be confirmed by the color of the label.

·

If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).

·

After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).

-

Turn the power switch on (READY).

-

Turn the power switch off and wait for 30 seconds or more.

-

Turn the power switch on (READY) again.




PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide G920NB 3.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A430691C01
2.063,0.094 2.375,0.292 0.313,0.198 10 false *a 2.365,0.313 2.677,0.51 0.313,0.198 10 false *a 2.74,0.594 3.052,0.792 0.313,0.198 10 false *a 3.104,0.823 3.365,1.021 0.26,0.198 10 false *a 3.01,1.531 3.271,1.729 0.26,0.198 10 false *a 2.26,1.948 2.521,2.146 0.26,0.198 10 false *a 0.031,0.073 0.292,0.271 0.26,0.198 10 false *a 0.01,0.583 0.271,0.781 0.26,0.198 10 false *b 0.229,1.021 0.49,1.219 0.26,0.198 10 false *a 0.51,1.271 0.771,1.469 0.26,0.198 10 false *b 0.833,1.531 1.094,1.729 0.26,0.198 10 false *b 1.198,1.844 1.458,2.042 0.26,0.198 10 false *b
*a Bolt
*b Nut


Remove the 8 bolts, 4 nuts and upper HV battery cover sub-assembly from the HV battery.


Hide G92Q1 4.REMOVE NO. 1 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A430733

Disengage the clamp.


b.

Disconnect the battery voltage sensor connector.


c.
A430734

Remove the bolt and nut.


d.
A430735C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 HV battery shield from the HV battery.


Hide 89892A 5.REMOVE BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A430736

Disconnect the battery voltage sensor connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A430737

Remove the bolt and battery voltage sensor from the HV battery.

NOTICE:

If the battery voltage sensor has been struck or dropped, replace it.