This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AEC | Front Sensor Communication Malfunction | An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the ignition switch is ON. | ·
Front ultrasonic sensor circuit ·
Harness or connector ·
Clearance warning ECU assembly |
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTCs is not output | A |
| DTC C1AEC is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the G25*1 or H4*2 clearance warning ECU assembly connector.
*1: for LHD and Manual Transaxle
*2: except LHD and Manual Transaxle
Disconnect the B6 front corner ultrasonic sensor (FL sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-4 (BOF) - B6-1 (BI) | Always | Below 1 Ω |
| G25-8 (SOF) - B6-3 (SI) | Always | Below 1 Ω |
| G25-6 (E5) - B6-5 (EI) | Always | Below 1 Ω |
| G25-4 (BOF) or B6-1 (BI) - Body ground | Always | 10 kΩ or higher |
| G25-8 (SOF) or B6-3 (SI) - Body ground | Always | 10 kΩ or higher |
| G25-6 (E5) or B6-5 (EI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-4 (BOF) - B6-1 (BI) | Always | Below 1 Ω |
| H4-8 (SOF) - B6-3 (SI) | Always | Below 1 Ω |
| H4-6 (E5) - B6-5 (EI) | Always | Below 1 Ω |
| H4-4 (BOF) or B6-1 (BI) - Body ground | Always | 10 kΩ or higher |
| H4-8 (SOF) or B6-3 (SI) - Body ground | Always | 10 kΩ or higher |
| H4-6 (E5) or B6-5 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B6 front corner ultrasonic sensor (FL sensor) connector.
Disconnect the B8 front center ultrasonic sensor (FLC sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B6-2 (BO) - B8-1 (BI) | Always | Below 1 Ω |
| B6-4 (SO) - B8-3 (SI) | Always | Below 1 Ω |
| B6-6 (EO) - B8-5 (EI) | Always | Below 1 Ω |
| B6-2 (BO) or B8-1 (BI) - Body ground | Always | 10 kΩ or higher |
| B6-4 (SO) or B8-3 (SI) - Body ground | Always | 10 kΩ or higher |
| B6-6 (EO) or B8-5 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B8 front center ultrasonic sensor (FLC sensor) connector.
Disconnect the B7 front center ultrasonic sensor (FRC sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B8-2 (BO) - B7-1 (BI) | Always | Below 1 Ω |
| B8-4 (SO) - B7-3 (SI) | Always | Below 1 Ω |
| B8-6 (EO) - B7-5 (EI) | Always | Below 1 Ω |
| B8-2 (BO) or B7-1 (BI) - Body ground | Always | 10 kΩ or higher |
| B8-4 (SO) or B7-3 (SI) - Body ground | Always | 10 kΩ or higher |
| B8-6 (EO) or B7-5 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B7 front center ultrasonic sensor (FRC sensor) connector.
Disconnect the B2 front corner ultrasonic sensor (FR sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B7-2 (BO) - B2-1 (BI) | Always | Below 1 Ω |
| B7-4 (SO) - B2-3 (SI) | Always | Below 1 Ω |
| B7-6 (EO) - B2-5 (EI) | Always | Below 1 Ω |
| B7-2 (BO) or B2-1 (BI) - Body ground | Always | 10 kΩ or higher |
| B7-4 (SO) or B2-3 (SI) - Body ground | Always | 10 kΩ or higher |
| B7-6 (EO) or B2-5 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front corner ultrasonic sensor (FR sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Inspect the front corner ultrasonic sensor (FR sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Remove the front center ultrasonic sensor (FRC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Inspect the front center ultrasonic sensor (FRC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Remove the front center ultrasonic sensor (FLC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Inspect the front center ultrasonic sensor (FLC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Remove the front corner ultrasonic sensor (FL sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Inspect the front corner ultrasonic sensor (FL sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Replace the front corner ultrasonic sensor (FL sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AEC is output | B |
A
B
Replace the front center ultrasonic sensor (FRC sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AEC is output | B |
A
B
Replace the front center ultrasonic sensor (FLC sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AEC is output | B |
A
B
Replace the front corner ultrasonic sensor (FL sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AEC is output | B |
A
B
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL