Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370876 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor (for Front) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for Gasoline model with parking support brake system)

·

Parking support brake system (for Gasoline model)


(Click here)
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for HV model with parking support brake system)

·

Parking support brake system (for HV model)


(Click here)
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89348X 2.REMOVE FRONT ULTRASONIC SENSOR CLIP (except Off Road Package)

a.

Detach the claw and remove the front ultrasonic sensor clip.

B525234C01
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.604,0.083 3.917,0.323 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Remove in this Direction - -



b.

Detach the wire harness clamp.

B525235C01
0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.583,0.083 3.896,0.333 0.313,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89341K 3.REMOVE FRONT CORNER ULTRASONIC SENSOR (except Off Road Package)

a.

Disconnect the connector.

B525236C01
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.5,0.094 3.813,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



b.

Detach the claw and remove the front corner ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and front bumper cover so that each sensor can be returned to its original position.


B525237C01
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.604,0.083 3.917,0.333 0.313,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Remove in this Direction - -



Hide 89341K 4.REMOVE FRONT CORNER ULTRASONIC SENSOR (for Off Road Package)

a.
B525413

Disconnect the connector.


b.
B525414C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front corner ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and front bumper cover so that each sensor can be returned to its original position.



Hide 89341L 5.REMOVE FRONT CENTER ULTRASONIC SENSOR (except Off Road Package)

a.

Disconnect the connector.

B525231C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.5,0.094 3.813,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



b.

Detach the claw and remove the front center ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and front bumper cover so that each sensor can be returned to its original position.


B525232C01
0.083,0.083 0.396,0.333 0.313,0.25 12 false *A 3.521,0.094 3.833,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Remove in this Direction - -



Hide 89341L 6.REMOVE FRONT CENTER ULTRASONIC SENSOR (for Off Road Package)

a.
B525415

Disconnect the connector.


b.
B525416C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front center ultrasonic sensor.

NOTICE:

Before removing the sensor, make sure to mark the sensor and front bumper cover so that each sensor can be returned to its original position.



Hide 89347B 7.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (except Off Road Package)

HINT:
·

Perform the following procedure only when replacement of a front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the front corner ultrasonic sensor retainer and front bumper assembly using a heat light.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

CAUTION:
E306500C76
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



Standard:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer



b.

Remove the front corner ultrasonic sensor retainer.

B525238C01
0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.438,0.094 3.75,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89347B 8.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (for Off Road Package)

HINT:
·

Perform the following procedure only when replacement of a front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the front corner ultrasonic sensor retainer and front bumper assembly using a heat light.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

CAUTION:
E306500C76
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



Standard:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer



b.
B525417

Remove the front corner ultrasonic sensor retainer.


Hide 89305 9.REMOVE ULTRASONIC SENSOR CUSHION SET (w/ Parking Support Brake System)

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Remove the ultrasonic sensor cushion set as shown in the illustration.

B549651C02
0,0 0,0 false
V113147

Remove in this Direction - -