This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for 8 Sensor Type | A |
| for 4 Sensor Type | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Active Test.
Check that the buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Buzzer | No. 1 clearance warning buzzer | Operate or Stop | Confirm that the vehicle is stopped and the ignition switch is ON |
| Tester Display |
|---|
| Front Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G25*1 or H4*2 clearance warning ECU assembly connector.
*1: for LHD and Manual Transaxle
*2: except LHD and Manual Transaxle
Disconnect the G71 No. 1 clearance warning buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-14 (CBZ) - G71-1 | Always | Below 1 Ω |
| G25-13 (EF) - G71-2 | Always | Below 1 Ω |
| G25-14 (CBZ) or G71-1 - Body ground | Always | 10 kΩ or higher |
| G25-13 (EF) or G71-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-14 (CBZ) - G71-1 | Always | Below 1 Ω |
| H4-13 (EF) - G71-2 | Always | Below 1 Ω |
| H4-14 (CBZ) or G71-1 - Body ground | Always | 10 kΩ or higher |
| H4-13 (EF) or G71-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 clearance warning buzzer with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Active Test.
Check that the buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Buzzer | No. 1 clearance warning buzzer | Operate or Stop | Confirm that the vehicle is stopped and the ignition switch is ON |
| Tester Display |
|---|
| Front Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Active Test.
Check that the buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer | No. 1 clearance warning buzzer | Operate or Stop | Confirm that the vehicle is stopped and the ignition switch is ON |
| Tester Display |
|---|
| Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G25*1 or H4*2 clearance warning ECU assembly connector.
*1: for LHD and Manual Transaxle
*2: except LHD and Manual Transaxle
Disconnect the G71 No. 1 clearance warning buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-14 (CBZ) - G71-1 | Always | Below 1 Ω |
| G25-13 (EF) - G71-2 | Always | Below 1 Ω |
| G25-14 (CBZ) or G71-1 - Body ground | Always | 10 kΩ or higher |
| G25-13 (EF) or G71-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-14 (CBZ) - G71-1 | Always | Below 1 Ω |
| H4-13 (EF) - G71-2 | Always | Below 1 Ω |
| H4-14 (CBZ) or G71-1 - Body ground | Always | 10 kΩ or higher |
| H4-13 (EF) or G71-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 clearance warning buzzer with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Active Test.
Check that the buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer | No. 1 clearance warning buzzer | Operate or Stop | Confirm that the vehicle is stopped and the ignition switch is ON |
| Tester Display |
|---|
| Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL