Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING BUZZER (for Front Side) › 2018.10–2019.02
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370874 CLEARANCE WARNING BUZZER(for Front Side) A

PARK ASSIST / MONITORING  CLEARANCE WARNING BUZZER(for Front Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 clearance warning buzzer removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision System
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 67914B 1.REMOVE FRONT DOOR SCUFF PLATE LH (for LHD, Manual Transaxle)

Hide 62112 2.REMOVE COWL SIDE TRIM BOARD LH (for LHD, Manual Transaxle)

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD, Manual Transaxle)

Hide 55545 4.REMOVE FUSE BOX OPENING COVER (for LHD, Manual Transaxle)

Hide 89343C 5.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for LHD, Manual Transaxle)

a.
B525193

Disconnect the connector.


b.

Detach the clamp and remove the No. 1 clearance warning buzzer.


Hide 6. PRECAUTION (except LHD, Manual Transaxle)

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 7.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 8.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 9.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 10.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (except LHD, Manual Transaxle)

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 73900 11.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD, except Manual Transaxle)

Hide 55308B 12.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD, except Manual Transaxle)

Hide 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD, except Manual Transaxle)

Hide 89343C 14.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for LHD, except Manual Transaxle)

a.
E405822

Detach the claw and remove the junction block bracket from the instrument panel junction block assembly with main body ECU.


b.
B525194C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the No. 1 clearance warning buzzer.


Hide 73900 15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

Hide 55308B 16.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for RHD)

Hide 89343C 17.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for RHD)

a.
B525197

Disconnect the connector.


b.

Detach the clamp and remove the No. 1 clearance warning buzzer.