There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Occupant Classification System *2: for 4WD/AWD |
|
| Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus wire ·
Short in CAN branch wire ·
Central gateway ECU (network gateway ECU) ·
Steering sensor ·
Occupant detection ECU*1 ·
Rack and pinion power steering gear assembly ·
Brake actuator assembly (skid control ECU) ·
4WD ECU assembly*2 ·
Airbag sensor assembly ·
No. 1 CAN junction connector ·
No. 4 CAN junction connector ·
No. 6 CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to No. 6 CAN Junction Connector | *d | to Steering Sensor |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G96-9 (CANH) - G96-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| G96-10 (CANH) - G96-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| G96-11 (CANH) - G96-22 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 6 CAN junction connector CAN main wire) | B |
| NG (No. 4 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G96 No. 1 CAN junction connector.
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Occupant Detection ECU (w/ Occupant Classification System) |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to No. 1 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*: w/ Occupant Classification System |
|||
| M31-2 (CANH) - M31-8 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Occupant detection ECU* |
| M31-3 (CANH) - M31-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| M31-4 (CANH) - M31-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | B |
| NG (No. 1 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G96 No. 1 CAN junction connector.
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Brake Actuator Assembly (Skid Control ECU) |
| *c | to Airbag Sensor Assembly | *d | to 4WD ECU Assembly (for 4WD/AWD) |
| *e | to No. 1 CAN Junction Connector | *f | to Rack and Pinion Power Steering Gear Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*: for 4WD/AWD |
|||
| G104-1 (CANH) - G104-7 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| G104-2 (CANH) - G104-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Airbag sensor assembly |
| G104-3 (CANH) - G104-9 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU assembly* |
| G104-4 (CANH) - G104-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| G104-5 (CANH) - G104-11 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Rack and pinion power steering gear assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Airbag sensor assembly CAN main wire) | B |
| NG (No. 1 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the M31 No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-22 (CA2H) - G72-7 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the G104 No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Disconnect the airbag sensor assembly connector.
w/ Occupant Classification System:
w/o Occupant Classification System:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-26 (CANH) - G70-27 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-22 (CA2H) - G72-7 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Proceed to |
|---|
| OK |
| NG |
OK
NG