Home › Drivetrain › K120 (MULTIDRIVE / CVT) › PARK / NEUTRAL POSITION SWITCH
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0371724 PARK / NEUTRAL POSITION SWITCH A

K120 MULTIDRIVE / CVT  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.

Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.


b.
C400913

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


c.
C420965C01
0.49,1.448 0.708,1.656 0.219,0.208 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C416210C01
1.615,0.552 1.823,0.25 1.823,0.25 1.99,0.25 true 1.958,1.344 2.25,0.938 2.25,0.938 2.729,0.938 true 1.531,1.813 1.99,1.813 true 2.042,0.146 2.323,0.385 0.281,0.24 10 false *1 2.792,0.813 3.073,1.052 0.281,0.24 10 false *a 1.323,1.708 1.521,1.938 0.198,0.229 10 true *b
*1 Transmission Control Shaft Lever
*a Manual Valve Link Lever Sub-assembly
*b Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



d.

Remove the transmission control shaft lever from the manual valve lever shaft.


e.
C400915C03
2.552,0.604 2.969,0.365 2.969,0.365 2.563,0.438 true 2.99,0.281 3.24,0.542 0.25,0.26 10 false *a
*a Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


f.

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


g.

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful of the direction of the transmission control shaft lever.



h.

Connect the park/neutral position switch assembly connector.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.


a.
C420965C01
0.49,1.448 0.708,1.656 0.219,0.208 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C416210C01
1.615,0.552 1.823,0.25 1.823,0.25 1.99,0.25 true 1.958,1.344 2.25,0.938 2.25,0.938 2.729,0.938 true 1.531,1.813 1.99,1.813 true 2.042,0.146 2.323,0.385 0.281,0.24 10 false *1 2.792,0.813 3.073,1.052 0.281,0.24 10 false *a 1.323,1.708 1.521,1.938 0.198,0.229 10 true *b
*1 Transmission Control Shaft Lever
*a Manual Valve Link Lever Sub-assembly
*b Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



b.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


c.
C400908C02
0.51,2.073 0.823,2.229 0.313,0.156 10 false *a 1.948,2.083 2.26,2.24 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.


Hide 74404B 3.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 84540 6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION