Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for M20A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371963 STOP AND START SYSTEM(for M20A-FKS) J

STOP AND START  STOP AND START SYSTEM(for M20A-FKS)  Starter Signal Circuit  


DESCRIPTION

for Continuously variable transaxle:

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

for Manual transaxle:

The engine stop and start ECU can activates the ST NO. 1 relay to operation the starter assembly.

WIRING DIAGRAM

for Continuously variable transaxle



A436149E01
0,0.021 2.5,0.375 2.5,0.354 10 false w/ Entry and Start System: 0.281,0.969 0.74,1.167 0.458,0.198 10 false ALT 0.438,1.708 0.896,1.906 0.458,0.198 10 false J/B-B 1.604,3.021 2.063,3.219 0.458,0.198 10 false AM2 1.563,3.219 4.771,3.5 3.208,0.281 10 false Instrument Panel Junction Block Assembly 2.302,2.396 3.073,2.615 0.771,0.219 10 false IG2 NO. 2 3,1.854 3.833,2.073 0.833,0.219 10 false METER-IG2 3.094,0.76 3.927,0.979 0.833,0.219 10 false EPS-IG1 2.333,1.25 3.104,1.469 0.771,0.219 10 false IG1 NO. 1 1.167,3.958 2.323,4.219 1.156,0.26 10 false EFI-MAIN NO. 1 4.406,3.958 5.563,4.219 1.156,0.26 10 false EFI NO. 1 2.542,4.448 3.698,4.708 1.156,0.26 10 false EFI-MAIN NO. 1 2.708,5.615 3.865,5.875 1.156,0.26 10 false IG2 NO. 1 5.51,0.594 6.344,0.813 0.833,0.219 10 false A32 5.49,1.719 6.323,1.938 0.833,0.219 10 false A32 5.51,3.802 6.344,4.021 0.833,0.219 10 false A34 5.5,6.271 6.333,6.49 0.833,0.219 10 false A34 2.313,7.25 3.833,7.771 1.521,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.677,8.281 7.063,8.688 1.385,0.406 10 false Engine Stop and Start ECU 0.146,7.594 1.302,7.854 1.156,0.26 10 false F 5.469,4.958 6.625,5.219 1.156,0.26 10 false A 3.854,4.177 5.01,4.438 1.156,0.26 10 false B 2.052,6.26 3.208,6.521 1.156,0.26 10 false G54 2.063,6.917 3.219,7.177 1.156,0.26 10 false G54 2.469,6.271 3.625,6.531 1.156,0.26 10 false IG1D 2.521,6.906 3.677,7.167 1.156,0.26 10 false +B 3.125,6.281 4.281,6.542 1.156,0.26 10 false STAR 3.229,6.927 4.385,7.188 1.156,0.26 10 false STA 3.656,6.271 4.813,6.531 1.156,0.26 10 false A15 3.677,6.906 4.833,7.167 1.156,0.26 10 false A15 2.094,6.031 3.25,6.292 1.156,0.26 10 false 17 2.156,6.688 3.313,6.948 1.156,0.26 10 false 4 3.771,6.042 4.927,6.302 1.156,0.26 10 false 9 3.698,6.708 4.854,6.969 1.156,0.26 10 false 20 4.698,8.094 5.854,8.354 1.156,0.26 10 false D 4.313,8.104 5.469,8.365 1.156,0.26 10 false C 5.104,8.094 6.26,8.354 1.156,0.26 10 false E 5.948,0.604 6.781,0.823 0.833,0.219 10 false IG1 5.938,1.708 6.771,1.927 0.833,0.219 10 false IG2 5.938,3.813 6.771,4.031 0.833,0.219 10 false +B 5.917,6.271 6.75,6.49 0.833,0.219 10 false CLL 5.531,6.042 6.365,6.26 0.833,0.219 10 false 17 5.573,3.583 6.406,3.802 0.833,0.219 10 false 1 5.51,1.49 6.344,1.708 0.833,0.219 10 false 18*1 4.99,0.375 5.823,0.594 0.833,0.219 10 false 21*2 1.135,0.594 1.594,0.792 0.458,0.198 10 false 4K 1.177,1.365 1.635,1.563 0.458,0.198 10 false 4L 1.156,2.063 1.615,2.26 0.458,0.198 10 false 4A 1.167,2.854 1.625,3.052 0.458,0.198 10 false 4A 4.156,2.74 4.615,2.938 0.458,0.198 10 false 4D 4.146,1.729 4.604,1.927 0.458,0.198 10 false 4D 4.146,0.583 4.604,0.781 0.458,0.198 10 false 4A 1.198,0.396 1.656,0.594 0.458,0.198 10 false 1 1.188,1.125 1.646,1.323 0.458,0.198 10 false 1 1.167,1.854 1.625,2.052 0.458,0.198 10 false 17 1.167,2.667 1.625,2.865 0.458,0.198 10 false 44 4.156,0.375 4.615,0.573 0.458,0.198 10 false 55 4.135,1.5 4.594,1.698 0.458,0.198 10 false 32 4.188,2.521 4.646,2.719 0.458,0.198 10 false 3 2.552,3.708 3.01,3.906 0.458,0.198 10 false 3 3.344,4.865 3.802,5.063 0.458,0.198 10 false 3 2.552,4.073 3.01,4.271 0.458,0.198 10 false 1 3.375,3.698 3.833,3.896 0.458,0.198 10 false 5 3.354,4.073 3.813,4.271 0.458,0.198 10 false 2 3.344,5.229 3.802,5.427 0.458,0.198 10 false 2 2.594,5.229 3.052,5.427 0.458,0.198 10 false 1 2.594,4.865 3.052,5.063 0.458,0.198 10 false 5 1.323,5.125 2.479,5.385 1.156,0.26 10 false IG2-MAIN 4.24,5.135 5.396,5.396 1.156,0.26 10 false ECU-IG2 NO. 1 5.021,0.604 5.854,0.823 0.833,0.219 10 false G62 5.01,1.719 5.844,1.938 0.833,0.219 10 false G62 5.479,0.375 6.313,0.594 0.833,0.219 10 false 21*1 5.01,1.49 5.844,1.708 0.833,0.219 10 false 18*2 1.156,7.865 2.844,8.063 1.688,0.198 10 false *1: for LHD 1.156,8.177 2.844,8.375 1.688,0.198 10 false *2: for RHD 1.156,2.479 1.615,2.677 0.458,0.198 10 false 4F 1.167,2.281 1.625,2.479 0.458,0.198 10 false 13

A436150E01
0.073,0.042 2.802,0.344 2.729,0.302 10 false w/o Entry and Start System: 0.26,1.063 0.719,1.26 0.458,0.198 10 false ALT 0.438,1.75 0.896,1.948 0.458,0.198 10 false J/B-B 1.688,3.052 2.146,3.25 0.458,0.198 10 false AM2 3.26,0.792 3.906,0.99 0.646,0.198 10 false EPS-IG1 3.135,1.917 4.031,2.156 0.896,0.24 10 false METER-IG2 2.458,1.292 3.375,1.542 0.917,0.25 10 false IG1 NO. 1 2.438,2.427 3.354,2.677 0.917,0.25 10 false IG2 NO. 2 1.646,3.323 4.688,3.615 3.042,0.292 10 false Instrument Panel Junction Block Assembly 1.125,4.146 2.313,4.385 1.188,0.24 10 false EFI-MAIN NO. 1 1.26,5.198 2.448,5.438 1.188,0.24 10 false IG2-MAIN 4.365,4.135 5.552,4.375 1.188,0.24 10 false EFI NO. 1 2.521,4.635 3.708,4.875 1.188,0.24 10 false EFI-MAIN NO. 1 2.677,5.698 3.865,5.938 1.188,0.24 10 false IG2 NO. 1 1.802,6.854 4.021,7.125 2.219,0.271 10 false Ignition or Starter Switch Assembly 1.833,6.688 3.021,6.927 1.188,0.24 10 false G28 2.5,6.385 3.688,6.625 1.188,0.24 10 false AM1 2.313,6.375 3.5,6.615 1.188,0.24 10 false 7 3.302,6.115 4.49,6.354 1.188,0.24 10 false IG1 3.281,6.375 4.469,6.615 1.188,0.24 10 false ST1 3.656,6.375 4.844,6.615 1.188,0.24 10 false 5 3.667,6.115 4.854,6.354 1.188,0.24 10 false 8 5.667,7.833 7.073,8.198 1.406,0.365 10 false Engine Stop and Start ECU 0.156,7.344 1.344,7.583 1.188,0.24 10 false F 4.302,7.406 5.49,7.646 1.188,0.24 10 false D 5.094,7.396 6.281,7.635 1.188,0.24 10 false E 5.5,5.083 6.688,5.323 1.188,0.24 10 false A 3.865,4.365 5.052,4.604 1.188,0.24 10 false B 1.177,0.656 1.635,0.854 0.458,0.198 10 false 4K 1.188,1.406 1.646,1.604 0.458,0.198 10 false 4L 1.177,2.135 1.635,2.333 0.458,0.198 10 false 4A 1.146,2.938 1.604,3.135 0.458,0.198 10 false 4A 4.24,0.656 4.698,0.854 0.458,0.198 10 false 4A 4.271,1.802 4.729,2 0.458,0.198 10 false 4D 4.271,2.792 4.729,2.99 0.458,0.198 10 false 4D 5.479,0.656 5.938,0.854 0.458,0.198 10 false A32 5.49,1.781 5.948,1.979 0.458,0.198 10 false A32 5.51,4.021 5.969,4.219 0.458,0.198 10 false A34 5.5,6.479 5.958,6.677 0.458,0.198 10 false A34 5.948,0.646 6.406,0.844 0.458,0.198 10 false IG1 5.927,1.802 6.385,2 0.458,0.198 10 false IG2 5.927,4.021 6.385,4.219 0.458,0.198 10 false +B 5.948,6.479 6.406,6.677 0.458,0.198 10 false CLL 1.198,0.458 1.656,0.656 0.458,0.198 10 false 1 1.208,1.229 1.667,1.427 0.458,0.198 10 false 1 1.177,1.906 1.635,2.104 0.458,0.198 10 false 17 1.156,2.729 1.615,2.927 0.458,0.198 10 false 44 4.24,0.438 4.698,0.635 0.458,0.198 10 false 55 4.313,1.563 4.771,1.76 0.458,0.198 10 false 32 4.302,2.573 4.76,2.771 0.458,0.198 10 false 3 5.51,0.406 5.969,0.604 0.458,0.198 10 false 21*1 5.49,1.563 5.948,1.76 0.458,0.198 10 false 18*1 5.573,3.771 6.031,3.969 0.458,0.198 10 false 1 5.5,6.25 5.958,6.448 0.458,0.198 10 false 17 2.542,3.896 3,4.094 0.458,0.198 10 false 3 2.563,4.25 3.021,4.448 0.458,0.198 10 false 1 3.365,3.875 3.823,4.073 0.458,0.198 10 false 5 3.365,4.25 3.823,4.448 0.458,0.198 10 false 2 2.604,5.344 3.063,5.542 0.458,0.198 10 false 1 2.583,4.969 3.042,5.167 0.458,0.198 10 false 5 3.344,4.958 3.802,5.156 0.458,0.198 10 false 3 3.333,5.323 3.792,5.521 0.458,0.198 10 false 2 4.177,5.219 5.365,5.458 1.188,0.24 10 false ECU-IG2 NO. 1 5.042,1.792 5.5,1.99 0.458,0.198 10 false G62 5.021,0.656 5.479,0.854 0.458,0.198 10 false G62 5.021,0.417 5.479,0.615 0.458,0.198 10 false 21*2 5.021,1.563 5.479,1.76 0.458,0.198 10 false 18*2 1.385,7.844 3.073,8.042 1.688,0.198 10 false *1: for LHD 1.406,8.219 3.094,8.417 1.688,0.198 10 false *2: for RHD 1.135,2.542 1.594,2.74 0.458,0.198 10 false 4F 1.167,2.333 1.625,2.531 0.458,0.198 10 false 13

A436151E01
0.792,3.635 3.24,3.833 2.448,0.198 10 false Starter Assembly 1.417,7.406 3.865,7.604 2.448,0.198 10 false ECM 0.573,8.167 3.021,8.365 2.448,0.198 10 false Battery 1.781,8.375 4.229,8.573 2.448,0.198 10 false : CAN Communication Line 5.708,7.958 7.083,8.5 1.375,0.542 10 false Engine Stop and Start ECU 2.885,3.969 3.75,4.25 0.865,0.281 10 false ST NO. 2 2.854,2.615 3.719,2.896 0.865,0.281 10 false ST NO. 1 5.271,0.865 6.583,1.281 1.313,0.417 10 false Park/Neutral Position Switch Assembly 0.271,0.115 2.719,0.313 2.448,0.198 10 false F 1.073,1.125 3.521,1.323 2.448,0.198 10 false ST NO. 1 1.052,1.604 3.5,1.802 2.448,0.198 10 false ST NO. 2 4.01,0.125 4.427,0.479 0.417,0.354 10 false C 4.76,0.125 5.177,0.479 0.417,0.354 10 false D 2.75,1.875 3.615,2.156 0.865,0.281 10 false 3 3.49,1.875 4.354,2.156 0.865,0.281 10 false 5 2.75,2.198 3.615,2.479 0.865,0.281 10 false 1 3.479,2.188 4.344,2.469 0.865,0.281 10 false 2 2.76,3.219 3.625,3.5 0.865,0.281 10 false 3 2.76,3.552 3.625,3.833 0.865,0.281 10 false 1 3.49,3.229 4.354,3.51 0.865,0.281 10 false 5 3.49,3.542 4.354,3.823 0.865,0.281 10 false 2 0.677,3.063 3.125,3.26 2.448,0.198 10 false D1 1.083,3.052 3.531,3.25 2.448,0.198 10 false B 1.333,2.792 2.125,3.115 0.792,0.323 10 false SL1 1.333,3.344 2.125,3.667 0.792,0.323 10 false SL2 1.771,2.781 2.563,3.104 0.792,0.323 10 false C43 1.76,3.344 2.552,3.667 0.792,0.323 10 false C43 0.771,2.802 3.219,3 2.448,0.198 10 false 1 1.854,2.563 4.302,2.76 2.448,0.198 10 false 2 1.854,3.125 4.302,3.323 2.448,0.198 10 false 1 5.479,6.531 5.979,6.771 0.5,0.24 10 false A32 5.479,7.052 5.979,7.292 0.5,0.24 10 false A32 5.927,6.531 6.427,6.771 0.5,0.24 10 false CANH 5.927,7.052 6.427,7.292 0.5,0.24 10 false CANL 1.354,6.521 1.854,6.76 0.5,0.24 10 false CANH 1.365,7.073 1.865,7.313 0.5,0.24 10 false CANL 1.396,6.031 1.896,6.271 0.5,0.24 10 false NSW 1.344,5.563 1.844,5.802 0.5,0.24 10 false MREL 1.354,5.083 1.854,5.323 0.5,0.24 10 false IGSW 1.458,4.604 1.958,4.844 0.5,0.24 10 false STA 4.115,4.042 4.979,4.323 0.865,0.281 10 false A 4.469,4.052 5.333,4.333 0.865,0.281 10 false B 4.813,4.042 5.677,4.323 0.865,0.281 10 false E 5.948,3.656 6.448,3.896 0.5,0.24 10 false STA2 5.927,2.313 6.427,2.552 0.5,0.24 10 false STA 5.938,5.135 6.438,5.375 0.5,0.24 10 false GND1 5.938,5.625 6.438,5.865 0.5,0.24 10 false GND2 5.938,4.604 6.438,4.844 0.5,0.24 10 false DGND 5.51,2.313 6.01,2.552 0.5,0.24 10 false A34 5.51,3.667 6.01,3.906 0.5,0.24 10 false A34 5.51,4.604 6.01,4.844 0.5,0.24 10 false A34 5.51,5.146 6.01,5.385 0.5,0.24 10 false A33 5.51,5.635 6.01,5.875 0.5,0.24 10 false A33 5.563,2.115 6.063,2.354 0.5,0.24 10 false 21 5.563,3.448 6.063,3.688 0.5,0.24 10 false 23 5.604,4.917 6.104,5.156 0.5,0.24 10 false 8 5.604,5.427 6.104,5.667 0.5,0.24 10 false 2 5.604,4.385 6.104,4.625 0.5,0.24 10 false 6 5.469,6.302 5.969,6.542 0.5,0.24 10 false 13*1 5.469,6.854 5.969,7.094 0.5,0.24 10 false 14*1 5.281,0.677 5.698,1.031 0.417,0.354 10 false C31 4.844,0.406 5.26,0.76 0.417,0.354 10 false 4 5.135,1.365 5.552,1.719 0.417,0.354 10 false 5 1.833,5.927 4.281,6.125 2.448,0.198 10 false 23 1.833,4.479 4.281,4.677 2.448,0.198 10 false 30 0.99,7.406 3.438,7.604 2.448,0.198 10 false A24 1.844,4.958 4.292,5.156 2.448,0.198 10 false 2 1.833,5.448 4.281,5.646 2.448,0.198 10 false 15 1.833,6.354 4.281,6.552 2.448,0.198 10 false 8 1.823,6.865 4.271,7.063 2.448,0.198 10 false 18 4.115,1.552 4.531,1.906 0.417,0.354 10 false *3 2.604,8.031 5.052,8.302 2.448,0.271 10 false *3: w/ Entry and Start System 5.021,6.521 5.521,6.76 0.5,0.24 10 false G62 5.021,7.052 5.521,7.292 0.5,0.24 10 false G62 5,6.302 5.5,6.542 0.5,0.24 10 false 13*2 5.021,6.844 5.521,7.083 0.5,0.24 10 false 14*2 2.604,7.5 5.052,7.771 2.448,0.271 10 false *1: for LHD 2.615,7.771 5.063,8.042 2.448,0.271 10 false *2: for RHD

for Manual transaxle



A436847E01
0,0.021 2.5,0.375 2.5,0.354 10 false w/ Entry and Start System: 0.281,0.969 0.74,1.167 0.458,0.198 10 false ALT 0.438,1.708 0.896,1.906 0.458,0.198 10 false J/B-B 1.604,3.021 2.063,3.219 0.458,0.198 10 false AM2 1.563,3.219 4.771,3.5 3.208,0.281 10 false Instrument Panel Junction Block Assembly 2.302,2.396 3.073,2.615 0.771,0.219 10 false IG2 NO. 2 3,1.854 3.833,2.073 0.833,0.219 10 false METER-IG2 3.094,0.76 3.927,0.979 0.833,0.219 10 false EPS-IG1 2.333,1.25 3.104,1.469 0.771,0.219 10 false IG1 NO. 1 1.167,3.958 2.323,4.219 1.156,0.26 10 false EFI-MAIN NO. 1 4.406,3.958 5.563,4.219 1.156,0.26 10 false EFI NO. 1 2.542,4.448 3.698,4.708 1.156,0.26 10 false EFI-MAIN NO. 1 2.708,5.615 3.865,5.875 1.156,0.26 10 false IG2 NO. 1 5.51,0.594 6.344,0.813 0.833,0.219 10 false A32 5.49,1.719 6.323,1.938 0.833,0.219 10 false A32 5.51,3.802 6.344,4.021 0.833,0.219 10 false A34 5.5,6.271 6.333,6.49 0.833,0.219 10 false A34 2.313,7.25 3.833,7.771 1.521,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.677,8.281 7.063,8.688 1.385,0.406 10 false Engine Stop and Start ECU 0.146,7.594 1.302,7.854 1.156,0.26 10 false F 5.469,4.958 6.625,5.219 1.156,0.26 10 false A 3.854,4.177 5.01,4.438 1.156,0.26 10 false B 2.052,6.26 3.208,6.521 1.156,0.26 10 false G54 2.063,6.917 3.219,7.177 1.156,0.26 10 false G54 2.469,6.271 3.625,6.531 1.156,0.26 10 false IG1D 2.521,6.906 3.677,7.167 1.156,0.26 10 false +B 3.125,6.281 4.281,6.542 1.156,0.26 10 false STAR 3.229,6.927 4.385,7.188 1.156,0.26 10 false STA 3.656,6.271 4.813,6.531 1.156,0.26 10 false A15 3.677,6.906 4.833,7.167 1.156,0.26 10 false A15 2.094,6.031 3.25,6.292 1.156,0.26 10 false 17 2.156,6.688 3.313,6.948 1.156,0.26 10 false 4 3.771,6.042 4.927,6.302 1.156,0.26 10 false 9 3.698,6.708 4.854,6.969 1.156,0.26 10 false 20 4.698,8.094 5.854,8.354 1.156,0.26 10 false D 4.313,8.104 5.469,8.365 1.156,0.26 10 false C 5.104,8.094 6.26,8.354 1.156,0.26 10 false E 5.948,0.604 6.781,0.823 0.833,0.219 10 false IG1 5.938,1.708 6.771,1.927 0.833,0.219 10 false IG2 5.938,3.813 6.771,4.031 0.833,0.219 10 false +B 5.917,6.271 6.75,6.49 0.833,0.219 10 false CLL 5.531,6.042 6.365,6.26 0.833,0.219 10 false 17 5.573,3.583 6.406,3.802 0.833,0.219 10 false 1 5.51,1.49 6.344,1.708 0.833,0.219 10 false 18*1 4.99,0.375 5.823,0.594 0.833,0.219 10 false 21*2 1.135,0.583 1.594,0.781 0.458,0.198 10 false 4M 1.177,1.365 1.635,1.563 0.458,0.198 10 false 4L 1.156,2.063 1.615,2.26 0.458,0.198 10 false 4A 1.167,2.854 1.625,3.052 0.458,0.198 10 false 4A 4.156,2.74 4.615,2.938 0.458,0.198 10 false 4D 4.146,1.729 4.604,1.927 0.458,0.198 10 false 4D 4.146,0.583 4.604,0.781 0.458,0.198 10 false 4A 1.156,0.385 1.615,0.583 0.458,0.198 10 false 1*1 1.188,1.125 1.646,1.323 0.458,0.198 10 false 1 1.167,1.854 1.625,2.052 0.458,0.198 10 false 17 1.167,2.667 1.625,2.865 0.458,0.198 10 false 44 4.156,0.375 4.615,0.573 0.458,0.198 10 false 55 4.135,1.5 4.594,1.698 0.458,0.198 10 false 32 4.188,2.521 4.646,2.719 0.458,0.198 10 false 3 2.552,3.708 3.01,3.906 0.458,0.198 10 false 3 3.344,4.865 3.802,5.063 0.458,0.198 10 false 3 2.552,4.073 3.01,4.271 0.458,0.198 10 false 1 3.375,3.698 3.833,3.896 0.458,0.198 10 false 5 3.354,4.073 3.813,4.271 0.458,0.198 10 false 2 3.344,5.229 3.802,5.427 0.458,0.198 10 false 2 2.594,5.229 3.052,5.427 0.458,0.198 10 false 1 2.594,4.865 3.052,5.063 0.458,0.198 10 false 5 1.323,5.125 2.479,5.385 1.156,0.26 10 false IG2-MAIN 4.24,5.135 5.396,5.396 1.156,0.26 10 false ECU-IG2 NO. 1 5.021,0.604 5.854,0.823 0.833,0.219 10 false G62 5.01,1.719 5.844,1.938 0.833,0.219 10 false G62 5.479,0.375 6.313,0.594 0.833,0.219 10 false 21*1 5.01,1.49 5.844,1.708 0.833,0.219 10 false 18*2 0.979,7.458 2.667,7.656 1.688,0.198 10 false *1: for LHD 1,7.781 2.688,7.979 1.688,0.198 10 false *2: for RHD 1.156,2.479 1.615,2.677 0.458,0.198 10 false 4F 1.167,2.281 1.625,2.479 0.458,0.198 10 false 13 1.646,0.604 2.104,0.802 0.458,0.198 10 false 4K 1.667,0.385 2.125,0.583 0.458,0.198 10 false 1*2

A436848E01
0.073,0.042 2.802,0.344 2.729,0.302 10 false w/o Entry and Start System: 0.26,1.063 0.719,1.26 0.458,0.198 10 false ALT 0.438,1.75 0.896,1.948 0.458,0.198 10 false J/B-B 1.688,3.052 2.146,3.25 0.458,0.198 10 false AM2 3.26,0.792 3.906,0.99 0.646,0.198 10 false EPS-IG1 3.135,1.917 4.031,2.156 0.896,0.24 10 false METER-IG2 2.458,1.292 3.375,1.542 0.917,0.25 10 false IG1 NO. 1 2.438,2.427 3.354,2.677 0.917,0.25 10 false IG2 NO. 2 1.646,3.323 4.688,3.615 3.042,0.292 10 false Instrument Panel Junction Block Assembly 1.125,4.146 2.313,4.385 1.188,0.24 10 false EFI-MAIN NO. 1 1.26,5.198 2.448,5.438 1.188,0.24 10 false IG2-MAIN 4.365,4.135 5.552,4.375 1.188,0.24 10 false EFI NO. 1 2.521,4.635 3.708,4.875 1.188,0.24 10 false EFI-MAIN NO. 1 2.677,5.698 3.865,5.938 1.188,0.24 10 false IG2 NO. 1 1.802,6.854 4.021,7.125 2.219,0.271 10 false Ignition or Starter Switch Assembly 1.833,6.688 3.021,6.927 1.188,0.24 10 false G28 2.5,6.385 3.688,6.625 1.188,0.24 10 false AM1 2.313,6.375 3.5,6.615 1.188,0.24 10 false 7 3.302,6.115 4.49,6.354 1.188,0.24 10 false IG1 3.281,6.375 4.469,6.615 1.188,0.24 10 false ST1 3.656,6.375 4.844,6.615 1.188,0.24 10 false 5 3.667,6.115 4.854,6.354 1.188,0.24 10 false 8 5.667,7.833 7.073,8.198 1.406,0.365 10 false Engine Stop and Start ECU 0.156,7.344 1.344,7.583 1.188,0.24 10 false F 4.302,7.406 5.49,7.646 1.188,0.24 10 false D 5.094,7.396 6.281,7.635 1.188,0.24 10 false E 5.5,5.083 6.688,5.323 1.188,0.24 10 false A 3.865,4.365 5.052,4.604 1.188,0.24 10 false B 1.177,0.656 1.635,0.854 0.458,0.198 10 false 4M 1.188,1.406 1.646,1.604 0.458,0.198 10 false 4L 1.177,2.135 1.635,2.333 0.458,0.198 10 false 4A 1.146,2.938 1.604,3.135 0.458,0.198 10 false 4A 4.24,0.656 4.698,0.854 0.458,0.198 10 false 4A 4.271,1.802 4.729,2 0.458,0.198 10 false 4D 4.271,2.792 4.729,2.99 0.458,0.198 10 false 4D 5.479,0.656 5.938,0.854 0.458,0.198 10 false A32 5.49,1.781 5.948,1.979 0.458,0.198 10 false A32 5.51,4.021 5.969,4.219 0.458,0.198 10 false A34 5.5,6.479 5.958,6.677 0.458,0.198 10 false A34 5.948,0.646 6.406,0.844 0.458,0.198 10 false IG1 5.927,1.802 6.385,2 0.458,0.198 10 false IG2 5.927,4.021 6.385,4.219 0.458,0.198 10 false +B 5.948,6.479 6.406,6.677 0.458,0.198 10 false CLL 1.125,0.458 1.583,0.656 0.458,0.198 10 false 1*1 1.208,1.229 1.667,1.427 0.458,0.198 10 false 1 1.177,1.906 1.635,2.104 0.458,0.198 10 false 17 1.156,2.729 1.615,2.927 0.458,0.198 10 false 44 4.24,0.438 4.698,0.635 0.458,0.198 10 false 55 4.313,1.563 4.771,1.76 0.458,0.198 10 false 32 4.302,2.573 4.76,2.771 0.458,0.198 10 false 3 5.51,0.406 5.969,0.604 0.458,0.198 10 false 21*1 5.49,1.563 5.948,1.76 0.458,0.198 10 false 18*1 5.573,3.771 6.031,3.969 0.458,0.198 10 false 1 5.5,6.25 5.958,6.448 0.458,0.198 10 false 17 2.542,3.896 3,4.094 0.458,0.198 10 false 3 2.563,4.25 3.021,4.448 0.458,0.198 10 false 1 3.365,3.875 3.823,4.073 0.458,0.198 10 false 5 3.365,4.25 3.823,4.448 0.458,0.198 10 false 2 2.604,5.344 3.063,5.542 0.458,0.198 10 false 1 2.583,4.969 3.042,5.167 0.458,0.198 10 false 5 3.344,4.958 3.802,5.156 0.458,0.198 10 false 3 3.333,5.323 3.792,5.521 0.458,0.198 10 false 2 4.177,5.219 5.365,5.458 1.188,0.24 10 false ECU-IG2 NO. 1 5.042,1.792 5.5,1.99 0.458,0.198 10 false G62 5.021,0.656 5.479,0.854 0.458,0.198 10 false G62 5.021,0.417 5.479,0.615 0.458,0.198 10 false 21*2 5.021,1.563 5.479,1.76 0.458,0.198 10 false 18*2 1.385,7.844 3.073,8.042 1.688,0.198 10 false *1: for LHD 1.406,8.219 3.094,8.417 1.688,0.198 10 false *2: for RHD 1.135,2.542 1.594,2.74 0.458,0.198 10 false 4F 1.167,2.333 1.625,2.531 0.458,0.198 10 false 13 1.646,0.646 2.104,0.844 0.458,0.198 10 false 4K 1.635,0.458 2.094,0.656 0.458,0.198 10 false 1*2

A436152E01
0.823,2.667 3.271,2.865 2.448,0.198 10 false Starter Assembly 1.406,6.604 3.854,6.802 2.448,0.198 10 false ECM 0.583,7.271 3.031,7.469 2.448,0.198 10 false Battery 1.531,8.292 3.979,8.49 2.448,0.198 10 false : CAN Communication Line 5.708,7.188 7.083,7.729 1.375,0.542 10 false Engine Stop and Start ECU 2.729,2.948 3.594,3.229 0.865,0.281 10 false ST NO. 1 5.094,1 5.99,1.667 0.896,0.667 10 false Clutch Switch Assembly 0.25,0.167 2.698,0.365 2.448,0.198 10 false F 1.01,0.719 3.458,0.917 2.448,0.198 10 false ST NO. 1 3.781,0.177 4.198,0.531 0.417,0.354 10 false C 4.74,0.188 5.156,0.542 0.417,0.354 10 false D 2.594,2.177 3.458,2.458 0.865,0.281 10 false 3 3.354,2.156 4.219,2.438 0.865,0.281 10 false 5 2.604,2.51 3.469,2.792 0.865,0.281 10 false 1 3.385,2.49 4.25,2.771 0.865,0.281 10 false 2 0.677,1.958 3.125,2.156 2.448,0.198 10 false D1 1.094,1.979 3.542,2.177 2.448,0.198 10 false B 1.438,2.313 2.229,2.635 0.792,0.323 10 false SL1 1.865,2.281 2.656,2.604 0.792,0.323 10 false C43 0.74,1.708 3.188,1.906 2.448,0.198 10 false 1 1.896,2.052 4.344,2.25 2.448,0.198 10 false 2 5.521,5.677 6.021,5.917 0.5,0.24 10 false A32 5.51,6.198 6.01,6.438 0.5,0.24 10 false A32 5.958,5.677 6.458,5.917 0.5,0.24 10 false CANH 5.958,6.208 6.458,6.448 0.5,0.24 10 false CANL 1.333,5.688 1.833,5.927 0.5,0.24 10 false CANH 1.365,6.208 1.865,6.448 0.5,0.24 10 false CANL 1.375,5.177 1.875,5.417 0.5,0.24 10 false NSW 1.354,4.698 1.854,4.938 0.5,0.24 10 false MREL 1.323,4.25 1.823,4.49 0.5,0.24 10 false IGSW 1.469,3.76 1.969,4 0.5,0.24 10 false STA 4.125,3.198 4.99,3.479 0.865,0.281 10 false A 4.458,3.198 5.323,3.479 0.865,0.281 10 false B 4.823,3.208 5.688,3.49 0.865,0.281 10 false E 5.948,2.594 6.448,2.833 0.5,0.24 10 false STA 5.938,4.313 6.438,4.552 0.5,0.24 10 false GND1 5.969,4.76 6.469,5 0.5,0.24 10 false GND2 5.948,3.771 6.448,4.01 0.5,0.24 10 false DGND 5.479,2.604 5.979,2.844 0.5,0.24 10 false A34 5.5,3.75 6,3.99 0.5,0.24 10 false A34 5.521,4.292 6.021,4.531 0.5,0.24 10 false A33 5.521,4.781 6.021,5.021 0.5,0.24 10 false A33 5.563,2.354 6.063,2.625 0.5,0.271 10 false 21 5.594,4.094 6.094,4.333 0.5,0.24 10 false 8 5.583,4.573 6.083,4.813 0.5,0.24 10 false 2 5.531,3.521 6.031,3.76 0.5,0.24 10 false 6 5.49,5.458 5.99,5.698 0.5,0.24 10 false 13*1 5.5,6 6,6.24 0.5,0.24 10 false 14*1 5.073,0.823 5.49,1.177 0.417,0.354 10 false A81 4.635,0.771 5.052,1.125 0.417,0.354 10 false 1 4.656,2.094 5.073,2.448 0.417,0.354 10 false 2 1.854,5.052 4.302,5.25 2.448,0.198 10 false 23 1.813,3.646 4.26,3.844 2.448,0.198 10 false 30 0.938,6.604 3.385,6.802 2.448,0.198 10 false A24 1.844,4.063 4.292,4.26 2.448,0.198 10 false 2 1.833,4.552 4.281,4.75 2.448,0.198 10 false 15 1.865,5.5 4.313,5.698 2.448,0.198 10 false 8 1.875,6.031 4.323,6.229 2.448,0.198 10 false 18 3.917,1.771 4.333,2.125 0.417,0.354 10 false *3 2.604,7.656 5.052,7.927 2.448,0.271 10 false *3: w/ Entry and Start System 5.042,5.688 5.542,5.927 0.5,0.24 10 false G62 5.021,6.198 5.521,6.438 0.5,0.24 10 false G62 5.01,5.469 5.51,5.708 0.5,0.24 10 false 13*2 4.99,5.99 5.49,6.229 0.5,0.24 10 false 14*2 2.573,6.99 5.021,7.26 2.448,0.271 10 false *1: for LHD 2.604,7.333 5.052,7.604 2.448,0.271 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

for Continuously variable transaxle:

Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

for Continuously variable transaxle:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

·

for Manual transaxle:

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CRANKING
a.

Turn the ignition switch START and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank (for Continuously variable transaxle) B
Engine does not crank (for Manual transaxle) C



A

2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))

B

7.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))

C

29.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Check that the engine hood is closed.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

f.

Check whether the engine cranks while the Active Test "Starter(Hood Close)" is being performed.

NOTICE:

The Active Test "Starter(Hood Close)" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Proceed to
OK
NG



OK

GO TO DTC P160300 (CONFIRM CAUSE OF ENGINE STALL)

NG

3.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)
A346333C68
1.469,0.229 1.969,0.5 0.5,0.271 1.042,1.5 0.75,1.875 true 1.458,1.896 1.167,1.156 true 1.594,0.292 2.052,0.49 0.458,0.198 10 false A33 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.573,1.927 1,2.146 0.427,0.219 10 false BIN1 1.333,1.938 1.76,2.156 0.427,0.219 10 false BIN2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-1 (BIN2) - Body ground Always 9.5 to 14 V
A33-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - BATTERY)

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL POWER SOURCE CIRCUIT)
A436064C03
1.469,0.438 1.948,0.688 0.479,0.25 1.469,0.115 1.948,0.365 0.479,0.25 2.021,1.49 2.052,1.854 true 1.583,0.469 2.031,0.646 0.448,0.177 10 false G62 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.948,1.896 2.333,2.115 0.385,0.219 10 false IG1 1.583,0.146 2.031,0.323 0.448,0.177 10 false A32 2.083,0.177 2.396,0.375 0.313,0.198 10 false *1 2.094,0.49 2.406,0.688 0.313,0.198 10 false *2
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32*1-21 (IG1) - Body ground
G62*2-21 (IG1) - Body ground
Ignition switch ON 9.5 to 14 V


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (+B AND IG2 TERMINALS POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY))

5.CHECK HARNESS AND CONNECTOR (+B AND IG2 TERMINALS POWER SOURCE CIRCUIT)
A399107C16
1.813,0.75 2.26,1 0.448,0.25 4.729,0.615 5.188,0.865 0.458,0.25 4.729,0.26 5.188,0.51 0.458,0.25 1.031,2.156 1.115,1.542 true 4.615,2.167 4.667,1.802 true 0.219,0.198 0.531,0.396 0.313,0.198 10 false *a 1.917,0.802 2.229,1 0.313,0.198 10 false A34 4.823,0.667 5.26,0.854 0.438,0.188 10 false G62 0.896,2.208 1.208,2.406 0.313,0.198 10 false +B 4.531,2.219 4.844,2.417 0.313,0.198 10 false IG2 4.813,0.313 5.25,0.5 0.438,0.188 10 false A32 5.323,0.302 5.635,0.5 0.313,0.198 10 false *1 5.323,0.667 5.635,0.865 0.313,0.198 10 false *2
*1 for LHD *2 for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
A32*1-18 (IG2) - Body ground
G62*2-18 (IG2) - Body ground
Ignition switch ON 9.5 to 14 V


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY OR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY))

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (GND2) - Body ground Always Below 1 Ω
A33-8 (GND1) - Body ground Always Below 1 Ω
A34-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Check that the engine hood is closed.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

f.

Check whether the engine cranks while the Active Test "Starter(Hood Close)" is being performed.

NOTICE:

The Active Test "Starter(Hood Close)" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

8.READ VALUE USING GTS (NEUTRAL SWITCH)

B

17.CHECK ENGINE STOP AND START ECU (STA AND STA2 SIGNAL)
8.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

e.

In accordance with the display on the GTS, read the Data List.

OK:
GTS Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Result Proceed to
NG A
OK (w/ Entry and Start System) B
OK (w/o Entry and Start System) C



A

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

B

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - 2 (ST NO. 1 relay) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - 2 (ST NO. 1 relay) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-9 (STAR) or C31-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A288763C47
1.531,0.281 1.958,0.542 0.427,0.26 1.229,1.802 1.302,1.385 true 0.177,0.188 0.49,0.344 0.313,0.156 10 false *a 1.104,1.823 1.563,2.021 0.458,0.198 10 false CLL 1.635,0.323 2.094,0.521 0.458,0.198 10 false A34
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-17 (CLL) - Body ground Engine start 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
A416365C02
1.51,0.188 1.917,0.458 0.406,0.271 1.76,1.833 2.177,1.417 true 0.24,0.271 0.563,0.521 0.323,0.25 10 false *a 1.427,1.771 1.75,2.021 0.323,0.25 10 false AM1 1.594,0.24 1.917,0.49 0.323,0.25 10 false G28
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


a.

Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G28-7 (AM1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - C31-4 (B) Always Below 1 Ω
G28-5 (ST1) or C31-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK ENGINE STOP AND START ECU (STA AND STA2 SIGNAL)
A419453C45
3.25,0.479 3.771,0.792 0.521,0.313 4.198,2.219 3.76,1.229 true 3.479,2.24 3.427,1.344 true 2.781,2.229 3.26,1.333 true 3.354,2.281 4.135,2.479 0.781,0.198 10 false STA 4.042,2.281 4.698,2.469 0.656,0.188 10 false DGND 3.385,0.552 3.76,0.75 0.375,0.198 10 false A34 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 2.604,2.292 3.385,2.49 0.781,0.198 10 false STA2
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Connect an oscilloscope to the STA, STA2 and DGND terminals of the engine stop and start ECU connector.


b.
A285702E46
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.198,1.771 3.094,2.021 1.896,0.25 10 false 0.03 to 0.06 seconds 0.031,0.875 2.031,1.146 2,0.271 10 false (ST NO. 1 Relay) 0.031,1.458 1.865,1.656 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the ignition switch START.

Item Condition
Tester Connection A34-21 (STA) - A34-6 (DGND)
A34-23 (STA2) - A34-6 (DGND)
Condition Engine started by ignition switch operation

Result:
Result Proceed to
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: between 0.03 and 0.06 seconds A
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: not between 0.03 and 0.06 seconds B
ST NO. 1 relay turns on and ST NO. 2 relay does not turn on C
ST NO. 1 relay and ST NO. 2 relay do not turn on D


NOTICE:

After replacing the engine stop and start ECU, make sure that the drive plate and ring gear sub-assembly and starter pinion gear are not excessively worn. A malfunction in the delay circuit may cause the drive plate and ring gear sub-assembly or starter pinion gear to be worn or damaged.




A

18.INSPECT RELAY (ST NO. 1 RELAY AND ST NO. 2 RELAY)

B

C

3.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)

D

21.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - BODY GROUND)
18.INSPECT RELAY (ST NO. 1 RELAY AND ST NO. 2 RELAY)
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


b.

Inspect the ST NO. 2 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - BATTERY)

NG

REPLACE RELAY (ST NO. 1 RELAY OR ST NO. 2 RELAY)

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - BATTERY)
A436055C01
0.115,0.063 0.396,0.302 0.281,0.24 10 false *1 2.135,1.823 2.417,2.063 0.281,0.24 10 false *2 2.146,0.344 2.427,0.583 0.281,0.24 10 false *3
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 ST NO. 1 relay
*3 ST NO. 2 Relay


a.

Remove the ST NO. 1 relay and ST NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 9.5 to 14 V
5 (ST NO. 2 relay) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY OR ST NO. 2 RELAY - BATTERY)

20.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay and ST NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C43-2 (SL1) Always Below 1 Ω
3 (ST NO. 2 relay) - C43-1 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY OR ST NO. 2 RELAY - STARTER ASSEMBLY)

21.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY AND ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay and ST NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω
1 (ST NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY OR ST NO. 2 RELAY - BODY GROUND)

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector. (w/ Entry and Start System)


d.

Disconnect the park/neutral position switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A34-21 (STA) or 2 (ST NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-23 (STA2) - 2 (ST NO. 2 relay) Always Below 1 Ω
A34-23 (STA2) or 2 (ST NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)
a.

Connect the positive (+) lead of an oscilloscope to the positive (+) battery terminal and the negative (-) lead to the negative (-) battery terminal.


b.

While cranking the engine, count the number of times the waveform drops.

A285237E05
3.438,0.781 3.583,0.417 3.583,0.417 3.833,0.417 false 0.104,0.729 0.719,0.927 0.615,0.198 10 false Normal: 0.125,2.031 0.844,2.229 0.719,0.198 10 false Abnormal: 0.719,0.917 2.042,1.135 1.323,0.219 10 false Approximately 12 V 1.938,1.24 3.927,1.438 1.99,0.198 10 false 7.6 to 9.3 V* 3.906,0.323 5.667,0.542 1.76,0.219 10 false Approximately 0.1 seconds 3.396,1.698 5.073,1.896 1.677,0.198 10 false Less than 3 seconds 5.167,3.177 7.083,3.5 1.917,0.323 10 false *: Varies with battery condition 2.323,2.49 4.958,3.042 2.635,0.552 10 false If the waveform does not change either the starter inrush current reduction relay or starter assembly is not operating. 0.729,2.302 2.052,2.521 1.323,0.219 10 false Approximately 12 V

Standard:

Waveform drops 2 times


Result:
Number of Times Waveform Dropped Proceed to
0 times A
2 times B




A

25.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY

B

28.INSPECT STARTER ASSEMBLY
25.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY
A434148C01
2.375,1.26 2.729,0.354 2.729,0.354 2.938,0.354 true 2.458,1.708 2.74,2.771 2.74,2.771 2.875,2.771 true 0.208,0.208 0.448,0.49 0.24,0.281 10 false *1 2.99,0.24 3.229,0.521 0.24,0.281 10 false *a 2.958,2.708 3.198,2.99 0.24,0.281 10 false *b
*1 Starter Assembly
*a B Terminal
*b M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminals B and M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B Terminal - M Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.INSPECT STARTER ASSEMBLY (WIRE HARNESS)

NG

27.INSPECT STARTER ASSEMBLY (M TERMINAL)
26.INSPECT STARTER ASSEMBLY (WIRE HARNESS)
A434149C01
2.063,1.125 2.281,0.385 2.281,0.385 2.542,0.385 true 2.385,1.281 2.802,2.521 2.802,2.521 2.927,2.521 true 1.563,1.083 0.646,2.604 0.646,2.604 0.375,2.604 true 0.229,0.188 0.479,0.479 0.25,0.292 10 false *1 2.646,0.313 2.958,0.51 0.313,0.198 10 false *a 2.99,2.448 3.302,2.646 0.313,0.198 10 false *b 0.146,2.531 0.458,2.729 0.313,0.198 10 false *c
*1 Starter Assembly
*a Inspect Part
*b B Terminal
*c M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminal B of the starter inrush current reduction relay.


c.

Disconnect terminal M of the starter assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M Terminal - B Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STARTER ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS

27.INSPECT STARTER ASSEMBLY (M TERMINAL)
A434150C01
1.177,3.083 1.406,3.083 1.406,3.083 2.188,1.844 true 2.927,2.563 2.792,2.563 2.792,2.563 2.438,1.708 true 0.188,0.208 0.438,0.521 0.25,0.313 10 false *1 0.969,3.01 1.219,3.323 0.25,0.313 10 false *a 3.01,2.458 3.26,2.771 0.25,0.313 10 false *b
*1 Starter Assembly
*a Inspect Part
*b M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminal M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M Terminal - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STARTER INRUSH CURRENT REDUCTION RELAY

NG

REPLACE STARTER ASSEMBLY

28.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE STARTER ASSEMBLY

29.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Check that the engine hood is closed.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close).

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

f.

Check whether the engine cranks while the Active Test "Starter(Hood Close)" is being performed.

NOTICE:

The Active Test "Starter(Hood Close)" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

30.READ VALUE USING GTS (CLUTCH LOWER SWITCH)

B

39.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
30.READ VALUE USING GTS (CLUTCH LOWER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Lower Switch.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower Switch
50003 392 594

e.

Depress the clutch pedal and read the values displayed on the GTS.

OK:
GTS Display Condition Normal Condition
Clutch Lower Switch Fully Depressed ON
Fully Released OFF



Result:
Result Proceed to
NG A
OK (w/ Entry and Start System) B
OK (w/o Entry and Start System) C



A

31.INSPECT CLUTCH SWITCH ASSEMBLY

B

34.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)

C

36.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
31.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

B

33.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - 2 (ST NO. 1 relay) Clutch pedal fully depressed Below 1 Ω
Clutch pedal fully released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - 2 (ST NO. 1 relay) Clutch pedal fully depressed Below 1 Ω
Clutch pedal fully released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - A81-1 Always Below 1 Ω
A15-9 (STAR) or A81-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A288763C47
1.531,0.281 1.958,0.542 0.427,0.26 1.229,1.802 1.302,1.385 true 0.177,0.188 0.49,0.344 0.313,0.156 10 false *a 1.104,1.823 1.563,2.021 0.458,0.198 10 false CLL 1.635,0.323 2.094,0.521 0.458,0.198 10 false A34
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-17 (CLL) - Body ground Engine start 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

36.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

37.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
A416365C02
1.51,0.188 1.917,0.458 0.406,0.271 1.76,1.833 2.177,1.417 true 0.24,0.271 0.563,0.521 0.323,0.25 10 false *a 1.427,1.771 1.75,2.021 0.323,0.25 10 false AM1 1.594,0.24 1.917,0.49 0.323,0.25 10 false G28
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


a.

Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G28-7 (AM1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - A81-1 Always Below 1 Ω
G28-5 (ST1) or A81-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
A419453C46
3.25,0.479 3.771,0.792 0.521,0.313 4.198,2.219 3.76,1.229 true 2.885,2.25 3.427,1.344 true 2.76,2.281 3.542,2.479 0.781,0.198 10 false STA 4.042,2.281 4.698,2.469 0.656,0.188 10 false DGND 3.385,0.552 3.76,0.75 0.375,0.198 10 false A34 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-21 (STA) - A34-6 (DGND) Engine start 6 to 14 V



Result:
Proceed to
OK
NG



OK

40.INSPECT RELAY (ST NO. 1 RELAY)

NG

3.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)
40.INSPECT RELAY (ST NO. 1 RELAY)
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY)

NG

REPLACE RELAY (ST NO. 1 RELAY)

41.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

42.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - BATTERY)

42.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C43-2 (SL1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

43.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

43.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector. (w/ Entry and Start System)


d.

Disconnect the clutch switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A34-21 (STA) or 2 (ST NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

45.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)
a.

Connect the positive (+) lead of an oscilloscope to the positive (+) battery terminal and the negative (-) lead to the negative (-) battery terminal.


b.

While cranking the engine, count the number of times the waveform drops.

A285237E05
3.438,0.781 3.583,0.417 3.583,0.417 3.833,0.417 false 0.104,0.729 0.719,0.927 0.615,0.198 10 false Normal: 0.125,2.031 0.844,2.229 0.719,0.198 10 false Abnormal: 0.719,0.917 2.042,1.135 1.323,0.219 10 false Approximately 12 V 1.938,1.24 3.927,1.438 1.99,0.198 10 false 7.6 to 9.3 V* 3.906,0.323 5.667,0.542 1.76,0.219 10 false Approximately 0.1 seconds 3.396,1.698 5.073,1.896 1.677,0.198 10 false Less than 3 seconds 5.167,3.177 7.083,3.5 1.917,0.323 10 false *: Varies with battery condition 2.323,2.49 4.958,3.042 2.635,0.552 10 false If the waveform does not change either the starter inrush current reduction relay or starter assembly is not operating. 0.729,2.302 2.052,2.521 1.323,0.219 10 false Approximately 12 V

Standard:

Waveform drops 2 times


Result:
Number of Times Waveform Dropped Proceed to
0 times A
2 times B




A

46.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY

B

49.INSPECT STARTER ASSEMBLY
46.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY
A434144C02
2.375,1.333 2.729,0.427 2.729,0.427 2.938,0.427 true 2.458,1.771 2.74,2.833 2.74,2.833 2.875,2.833 true 0.208,0.208 0.448,0.49 0.24,0.281 10 false *1 3.021,0.333 3.26,0.615 0.24,0.281 10 false *a 2.969,2.75 3.208,3.031 0.24,0.281 10 false *b
*1 Starter Assembly
*a B Terminal
*b M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminals B and M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B Terminal - M Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

47.INSPECT STARTER ASSEMBLY (WIRE HARNESS)

NG

48.INSPECT STARTER ASSEMBLY (M TERMINAL)
47.INSPECT STARTER ASSEMBLY (WIRE HARNESS)
A434145C02
2.104,0.896 2.281,0.385 2.281,0.385 2.542,0.385 true 2.385,1.333 2.802,2.521 2.802,2.521 2.927,2.521 true 1.354,1.208 0.646,2.604 0.646,2.604 0.375,2.604 true 0.229,0.188 0.479,0.479 0.25,0.292 10 false *1 2.646,0.313 2.958,0.51 0.313,0.198 10 false *a 2.99,2.448 3.302,2.646 0.313,0.198 10 false *b 0.146,2.531 0.458,2.729 0.313,0.198 10 false *c
*1 Starter Assembly
*a Inspect Part
*b B Terminal
*c M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminal B of the starter inrush current reduction relay.


c.

Disconnect terminal M of the starter assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M Terminal - B Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS

48.INSPECT STARTER ASSEMBLY (M TERMINAL)
A434146C02
1.177,3.083 1.406,3.083 1.406,3.083 2.25,1.948 true 2.927,2.563 2.792,2.563 2.792,2.563 2.458,1.76 true 0.188,0.208 0.438,0.521 0.25,0.313 10 false *1 0.969,3.01 1.219,3.323 0.25,0.313 10 false *a 3.01,2.458 3.26,2.771 0.25,0.313 10 false *b
*1 Starter Assembly
*a Inspect Part
*b M Terminal


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminal M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M Terminal - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STARTER INRUSH CURRENT REDUCTION RELAY

NG

49.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG