Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY
RM3620E _58 Vehicle Interior _076405 SEAT _0372018 REAR SEAT ASSEMBLY A

SEAT  REAR SEAT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
B521792

·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



PROCEDURE

Hide 71033 1.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY (for HV Model)

a.
A433772C02
2.177,1.833 2.396,2.063 0.219,0.229 10 true (1) 2.688,0.167 2.906,0.396 0.219,0.229 10 true (3) 1.115,1.833 1.333,2.063 0.219,0.229 10 true (1) 2.646,1.844 2.865,2.073 0.219,0.229 10 true (2) 0.646,1.844 0.865,2.073 0.219,0.229 10 true (2) 0.552,0.167 0.771,0.396 0.219,0.229 10 true (3)
V113147

Install in this Direction


Attach the guide.


b.

Temporarily install the rear seat cushion leg sub-assembly with the 6 bolts.


c.

Tighten the 6 bolts in the order shown in the illustration.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 58464D 2.INSTALL BATTERY SERVICE COVER BOARD (for HV Model)

Hide 58467H 3.INSTALL NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)

Hide 58466J 4.INSTALL NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)

Hide 67918E 5.INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)

Hide 67917C 6.INSTALL REAR DOOR SCUFF PLATE RH (for HV Model)

HINT:

Use the same procedure as for the LH side.


Hide 71304C 7.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.
B521819N02
1.219,1.698 1.406,1.896 0.188,0.198 10 true (2) 1.771,1.781 1.969,1.979 0.198,0.198 10 true (1)

Temporarily install the rear seatback hinge sub-assembly LH with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 71303C 8.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 71305A 9.INSTALL REAR CENTER SEATBACK HINGE SUB-ASSEMBLY

a.
B521818N02
1.917,1.927 2.104,2.125 0.188,0.198 10 true (1) 0.958,1.781 1.146,1.979 0.188,0.198 10 true (2)

Temporarily install the rear center seatback hinge sub-assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 10.INSTALL REAR SEATBACK ASSEMBLY RH

a.
B521817

Attach the guide.

NOTICE:

Be careful not to damage the rear seatback assembly RH, body exterior or interior parts.



b.
B521816N01
2.896,0.698 3.135,0.906 0.24,0.208 10 true (1) 2.052,0.01 2.292,0.219 0.24,0.208 10 true (2)

Install the rear seatback assembly RH with the 2 bolts in the order shown in the illustration.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


c.

Return the rear seatback assembly RH.


d.

w/ Seat Heater System:

i.
B521809

Attach the clamp.



e.
B521812

Attach the clip.


Hide 73350C 11.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)

Hide 12.INSTALL REAR SEATBACK ASSEMBLY LH

a.
B521814

Attach the guide.

NOTICE:

Be careful not to damage the rear seatback assembly LH, body exterior or interior parts.



b.
B521813N01
2.552,0.052 2.792,0.26 0.24,0.208 10 true (1) 3.01,0.667 3.25,0.875 0.24,0.208 10 true (2)

Install the rear seatback assembly LH with the 2 bolts in the order shown in the illustration.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


c.

Return the rear seatback assembly LH.


d.

w/ Seat Heater System:

i.
B521810

Attach the clamp.



e.
B521811

Attach the clip.


Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK

HINT:

Use the same procedure for the 2 parts.


a.

Set a new rear seat cushion lock hook.


b.
B372783C11
1.042,2.823 1.271,3.01 1.271,3.01 1.479,3.01 true 1.521,2.938 1.833,3.135 0.313,0.198 10 false *a
*a Sleeve
V100155

Protective Tape


Using 2 thin-bladed screwdrivers, push the sleeve to attach the claw.

NOTICE:

Do not apply excessive force which may break the sleeve.


HINT:

Tape the thin-bladed screwdriver tip before use.



c.

Check the installation condition.

OK:

The sleeve is installed properly.


B372789C06
0.521,1.375 0.896,1.375 false 1.625,1.458 1.646,1.792 1.646,1.792 1.833,1.792 false 1.073,1.781 0.604,1.781 true 1.146,0.552 1.458,0.75 0.313,0.198 10 false *d 2.719,0.573 3.031,0.771 0.313,0.198 10 false *e 4.25,0.573 4.563,0.771 0.313,0.198 10 false *e 5.844,0.583 6.156,0.781 0.313,0.198 10 false *e 0.333,1.281 0.646,1.479 0.313,0.198 10 false *a 1.906,1.729 2.219,1.927 0.313,0.198 10 false *b 0.417,1.708 0.729,1.906 0.313,0.198 10 false *c
*a Body *b Vehicle
*c Sleeve *d Correct
*e Incorrect - -



Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

a.

Place the bench type rear seat cushion assembly in the vehicle.

NOTICE:

Be careful not to damage the bench type rear seat cushion assembly, body exterior or interior parts.



b.

w/ Occupant Detection Sensor:

i.
B521807C01
0.365,0.333 0.604,0.563 0.24,0.229 12 true *B 1.135,0.5 1.375,0.729 0.24,0.229 12 true *A 2,0.292 2.24,0.521 0.24,0.229 12 true *A 2.365,0.104 2.604,0.333 0.24,0.229 12 true *A 3.125,0.323 3.365,0.552 0.24,0.229 12 true *B 0.688,0.365 0.927,0.594 0.24,0.229 12 true *B 2.656,0.198 2.896,0.427 0.24,0.229 12 true *B
*A w/ Occupant Detection Sensor
*B w/ Seat Heater System


Connect the 3 connectors for occupant detection sensor.



c.

w/ Seat Heater System:

i.

Connect the 4 connectors for seat heater.



d.
B521806C01
1.344,0.5 1.969,0.5 true 2,0.406 2.313,0.563 0.313,0.156 10 false *1
*1 Child Restraint Seat Anchor Bracket Sub-assembly
V113147

Install in this Direction


Attach the hook on the rear end of bench type rear seat cushion assembly under the 2 child restraint seat anchor bracket sub-assemblies.


e.
B521804C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration and attach the hook on the front of bench type rear seat cushion assembly to the rear seat cushion lock hook.

NOTICE:
·

Be sure to attach the hook on the front of bench type rear seat cushion assembly one at a time.

·

Check that the rear seat cushion lock hook and bench type rear seat cushion assembly are securely fastened.




Hide 15.INSPECT SEAT BELT WARNING SYSTEM (w/ Occupant Detection Sensor)

Hide 16.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)