Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for M20A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371963 STOP AND START SYSTEM(for M20A-FKS) C

STOP AND START  STOP AND START SYSTEM(for M20A-FKS)  P085012  Park/Neutral Switch Circuit Short to Battery  P085014  Park/Neutral Switch Circuit Short to Ground or Open  


DESCRIPTION

HINT:

This DTC is applicable to Continuously Variable Transaxle models only.


The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator, prohibits stop and start control and stores DTC P085012 or P085014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P085012 Park/Neutral Switch Circuit Short to Battery Both of the following conditions are met for 15 seconds or more (2 trip detection logic):
·

Ignition switch ON.

·

NSW signal is off with the shift lever in P or N.


·

Wire harness or connector

·

Park/Neutral position switch assembly

·

TCM

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0852
P085014 Park/Neutral Switch Circuit Short to Ground or Open Both of the following conditions are met for 2 seconds or more (2 trip detection logic):
·

Ignition switch ON.

·

NSW signal is on with the shift lever not in P or N.


·

Wire harness or connector

·

Park/Neutral position switch assembly

·

TCM

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0851

WIRING DIAGRAM

w/ Entry and Start System


A436054E01
3.25,0.542 5.49,0.865 2.24,0.323 10 false from BKUP LP Fuse 0.406,1.646 2.646,1.969 2.24,0.323 10 false ECM 3.656,4.042 5.979,4.719 2.323,0.677 10 false to ST NO. 1 Relay and Certification ECU (Smart Key ECU Assembly) 5.792,4.302 6.135,4.594 0.344,0.292 10 false A34 5.781,4.438 7.156,4.865 1.375,0.427 10 false Engine Stop and Start ECU 6.208,3.552 6.552,3.844 0.344,0.292 10 false STA 6.219,0.979 6.563,1.271 0.344,0.292 10 false CLL 5.948,3.417 6.292,3.708 0.344,0.292 10 false 21 5.948,0.854 6.292,1.146 0.344,0.292 10 false 17 0.552,0.979 1.042,1.271 0.49,0.292 10 false NSW 0.792,2.656 1.281,2.948 0.49,0.292 10 false P 0.781,3.24 1.271,3.531 0.49,0.292 10 false R 0.781,3.781 1.271,4.073 0.49,0.292 10 false N 0.792,4.417 1.281,4.708 0.49,0.292 10 false D 0.125,1.5 0.615,1.792 0.49,0.292 10 false A24 4.406,1.521 4.896,1.813 0.49,0.292 10 false C31 4.406,1.688 5.74,2.115 1.333,0.427 10 false Park/Neutral Position Switch Assembly 0.979,0.833 1.469,1.125 0.49,0.292 10 false 23 0.99,2.573 1.479,2.865 0.49,0.292 10 false 29 1,3.146 1.49,3.438 0.49,0.292 10 false 33 0.979,3.708 1.469,4 0.49,0.292 10 false 32 1,4.281 1.49,4.573 0.49,0.292 10 false 31 1.958,2.25 2.448,2.542 0.49,0.292 10 false PL 2.438,2.26 2.927,2.552 0.49,0.292 10 false RL 2.875,2.26 3.365,2.552 0.49,0.292 10 false NL 3.354,2.271 3.844,2.563 0.49,0.292 10 false DL 3.906,2.271 4.396,2.563 0.49,0.292 10 false L 2.698,1.406 3.188,1.698 0.49,0.292 10 false RB 3.885,1.396 4.375,1.688 0.49,0.292 10 false B 2.802,1.167 3.292,1.458 0.49,0.292 10 false 2 3.906,1.177 4.396,1.469 0.49,0.292 10 false 4 2.063,2.49 2.552,2.781 0.49,0.292 10 false 6 2.521,2.5 3.01,2.792 0.49,0.292 10 false 1 2.979,2.49 3.469,2.781 0.49,0.292 10 false 9 3.438,2.5 3.927,2.792 0.49,0.292 10 false 7 3.906,2.49 4.396,2.781 0.49,0.292 10 false 5 0.375,5.063 2.615,5.385 2.24,0.323 10 false TCM 0.125,4.865 0.615,5.156 0.49,0.292 10 false C33


w/o Entry and Start System


A436053E01
3.25,0.542 5.49,0.865 2.24,0.323 10 false from BKUP LP Fuse 0.406,1.646 2.646,1.969 2.24,0.323 10 false ECM 3.688,4.073 5.771,4.5 2.083,0.427 10 false to ST NO. 1 Relay 5.802,4.135 6.146,4.427 0.344,0.292 10 false A34 5.781,4.292 7.156,4.719 1.375,0.427 10 false Engine Stop and Start ECU 6.208,3.552 6.552,3.844 0.344,0.292 10 false STA 6.219,0.979 6.563,1.271 0.344,0.292 10 false CLL 5.948,3.417 6.292,3.708 0.344,0.292 10 false 21 5.948,0.854 6.292,1.146 0.344,0.292 10 false 17 0.552,0.979 1.042,1.271 0.49,0.292 10 false NSW 0.792,2.656 1.281,2.948 0.49,0.292 10 false P 0.781,3.24 1.271,3.531 0.49,0.292 10 false R 0.781,3.781 1.271,4.073 0.49,0.292 10 false N 0.792,4.417 1.281,4.708 0.49,0.292 10 false D 0.125,1.5 0.615,1.792 0.49,0.292 10 false A24 4.406,1.521 4.896,1.813 0.49,0.292 10 false C31 4.406,1.688 5.74,2.115 1.333,0.427 10 false Park/Neutral Position Switch Assembly 0.979,0.833 1.469,1.125 0.49,0.292 10 false 23 0.99,2.573 1.479,2.865 0.49,0.292 10 false 29 1,3.146 1.49,3.438 0.49,0.292 10 false 33 0.979,3.708 1.469,4 0.49,0.292 10 false 32 1,4.281 1.49,4.573 0.49,0.292 10 false 31 1.958,2.25 2.448,2.542 0.49,0.292 10 false PL 2.438,2.26 2.927,2.552 0.49,0.292 10 false RL 2.875,2.26 3.365,2.552 0.49,0.292 10 false NL 3.354,2.271 3.844,2.563 0.49,0.292 10 false DL 3.906,2.271 4.396,2.563 0.49,0.292 10 false L 2.698,1.406 3.188,1.698 0.49,0.292 10 false RB 3.885,1.396 4.375,1.688 0.49,0.292 10 false B 2.802,1.167 3.292,1.458 0.49,0.292 10 false 2 3.906,1.177 4.396,1.469 0.49,0.292 10 false 4 2.063,2.49 2.552,2.781 0.49,0.292 10 false 6 2.521,2.5 3.01,2.792 0.49,0.292 10 false 1 2.979,2.49 3.469,2.781 0.49,0.292 10 false 9 3.438,2.5 3.927,2.792 0.49,0.292 10 false 7 3.906,2.49 4.396,2.781 0.49,0.292 10 false 5 0.375,5.063 2.615,5.385 2.24,0.323 10 false TCM 0.125,4.865 0.615,5.156 0.49,0.292 10 false C33 2.344,0.188 5.323,0.74 2.979,0.552 10 false from Ignition or Starter Switch Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

for Continuously variable transaxle:

Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / Shift SW Status (P, R, N, D Range).

Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition
Shift SW Status (P Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Shift SW Status (R Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in R
ON: Shift lever in R
Shift SW Status (N Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
Shift SW Status (D Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in D or S
ON: Shift lever in D or S

Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (NEUTRAL POSITION SW)

NG

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.READ VALUE USING GTS (NEUTRAL POSITION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Neutral Position SW.

Powertrain > Engine > Data List
Tester Display
Neutral Position SW
50003 372 20

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition
Neutral Position SW Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU Assembly) connector. (w/ Entry and Start System)


e.

Disconnect the ignition or starter switch assembly connector. (w/o Entry and Start System)


f.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - C31-5 (L) Always Below 1 Ω
A34-17 (CLL) - C31-4 (B) Always Below 1 Ω
A34-21 (STA) or C31-5 (L) - Body ground and other terminals Always 10 kΩ or higher
A34-17 (CLL) or C31-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM, TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (ECM, TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-29 (P) - C31-6 (PL) Always Below 1 Ω
C33-33 (R) - C31-1 (RL) Always Below 1 Ω
C33-32 (N) - C31-9 (NL) Always Below 1 Ω
C33-31 (D) - C31-7 (DL) Always Below 1 Ω
A24-23 (NSW) - C31-4 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR