Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2018.10–2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15C4  SRS Communication Error  


DESCRIPTION

If the telephone transceiver assembly detects an error in communication between itself and the airbag sensor assembly as a result of a self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C4 SRS Communication Error The telephone transceiver assembly detects an error in signals from the airbag sensor assembly when the ignition switch is ON
·

Telephone transceiver assembly

·

Airbag sensor assembly

·

Harness or connector

·

Airbag system



WIRING DIAGRAM

E342824E55
1.208,0.833 1.823,1.031 0.615,0.198 10 false GSW3 5.531,0.854 6.146,1.052 0.615,0.198 10 false GSW 1.75,0.729 2.063,0.927 0.313,0.198 10 false 23 5.26,0.729 5.573,0.927 0.313,0.198 10 false 24 0.917,1.438 1.313,1.635 0.396,0.198 10 false G70 5.5,1.417 5.896,1.615 0.396,0.198 10 false H6 0.917,1.583 2.938,1.875 2.021,0.292 10 false Airbag Sensor Assembly 5.5,1.583 6.938,2.219 1.438,0.635 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

This vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Check if airbag system DTCs are output.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

B

2.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
B240640C46
1.521,0.083 1.917,0.344 0.396,0.26 2.354,1.25 2.563,1.698 2.563,1.698 2.688,1.698 false 0.125,0.125 0.396,0.385 0.271,0.26 10 false *a 2.729,1.625 3.177,1.906 0.448,0.281 10 false GSW 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND 1.625,0.135 2.073,0.417 0.448,0.281 10 false H6 0.177,2.125 0.448,2.385 0.271,0.26 10 false *b
*a Component with harness connected
(Telephone Transceiver Assembly)
*b Waveform


Check the output waveform.

i.

Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


ii.

Connect an oscilloscope to terminal H6-24 (GSW) - Body ground.


iii.

Turn the ignition switch to ON.


iv.

Check the signal waveform according to the condition(s) in the table below.

Reference Waveform:
Item Condition
Tester connection H6-24 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms/DIV.
Vehicle condition Ignition switch ON




b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-24 (GSW) - Body ground Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the G70 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-24 (GSW) - G70-23 (GSW3) Always Below 1 Ω
H6-24 (GSW) or G70-23 (GSW3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR