Home › Brake › BRAKE (FRONT) › FRONT BRAKE (except 2-Pot Caliper) › 2018.10–2020.08
RM3620E _54 Brake _076409 BRAKE (FRONT) _0372101 FRONT BRAKE(except 2-Pot Caliper) A

BRAKE (FRONT)  FRONT BRAKE(except 2-Pot Caliper)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (w/o Vacuum Brake Booster)

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.



Hide 2.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Hide 3.REMOVE FRONT WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47313J 5.DISCONNECT FRONT FLEXIBLE HOSE

a.
C397680

Remove the union bolt and gasket, and disconnect the front flexible hose from the front disc brake cylinder assembly.


Hide 47750 6.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY

a.
C397681C01
1.469,1.563 1.729,1.76 0.26,0.198 10 true *a 2,1.667 2.219,1.844 0.219,0.177 10 true *b
*a Turn
*b Hold


Hold the 2 front disc brake cylinder slide pins and remove the 2 bolts and front disc brake cylinder assembly.


Hide 7.REMOVE FRONT DISC BRAKE PAD

a.
C397682

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 04945 8.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 9.REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C397683

Remove the 4 front disc brake pad support plates from the front disc brake cylinder mounting.

NOTICE:

Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47715A 10.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C397684

Remove the 2 front disc brake cylinder slide pins from the front disc brake cylinder mounting.


b.
C397685C01
2.083,1.385 2.438,0.813 2.438,0.813 2.531,0.813 false 2.583,0.75 2.896,0.906 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake cylinder slide bushing from the front disc brake cylinder slide pin (lower side).

NOTICE:

Do not damage the front disc brake cylinder slide pin.



Hide 11.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT

a.
C397686

Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.


Hide 47722 12.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING

a.
C397687

Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.


Hide 43512 13.REMOVE FRONT DISC

a.
C397688C01
2.031,1 2.76,1 true 2.042,1.063 2.292,1.063 2.292,1.063 2.292,1 true 2.833,0.917 3.094,1.156 0.26,0.24 10 true *a
*a Matchmark


Put matchmarks on the front disc and the front axle hub sub-assembly.


b.

Remove the front disc.