Home › Brake › BRAKE (REAR) › REAR BRAKE › 2018.10–2019.02
RM3620E _54 Brake _076412 BRAKE (REAR) _0375827 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (w/o vacuum brake booster)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (w/o vacuum brake booster)

·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal. (w/o vacuum brake booster)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 2. PRECAUTION (w/o Vacuum Brake Booster)

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.



Hide 3.REMOVE REAR WHEEL

Hide 5.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:
·

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

·

Do not operate the electric parking brake switch assembly when the electric parking brake system is in rear brake pad replacement mode.




b.
C409058C01
0.021,0.01 0.229,0.188 0.208,0.177 10 true *A 0.031,2.333 0.26,2.521 0.229,0.188 10 true *B
*A for LHD
*B for RHD


Disconnect the reservoir level switch connector.


c.

Remove deck board assembly.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


d.

Remove rear No. 2 floor board.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


e.

Remove battery hole cover.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


g.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


h.

Check that the brake pedal cannot be further depressed.


Hide 6.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 7.SEPARATE REAR FLEXIBLE HOSE LH

a.
C406514C01
0.104,0.135 0.417,0.333 0.313,0.198 10 true *A 0.135,2.698 0.448,2.896 0.313,0.198 10 true *B
*A for Type A
*B for Type B


Remove the union bolt and gasket, and disconnect the rear flexible hose LH from the rear disc brake cylinder assembly.


Hide 890C0A 8.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 46310B 9.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY LH

Hide 10.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C406515C01
2.396,0.927 2.625,1.115 0.229,0.188 10 true *a 2.385,2.427 2.604,2.625 0.219,0.198 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 11.REMOVE REAR DISC BRAKE PAD

a.
C406516

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 12.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 13.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C406517

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 14.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C406518C01
2.26,1.49 2.073,1.781 true 2.417,0.573 2.292,0.323 true 2.25,1.26 2.5,1.469 0.25,0.208 10 true *1 2.417,0.625 2.615,0.865 0.198,0.24 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C406519C01
2.135,1.333 2.552,0.917 false 2.583,0.76 2.896,0.917 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 1 disc brake cylinder slide pin.



Hide 15.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C406520

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 16.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C406521

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.


Hide 42431B 17.REMOVE REAR DISC

a.
C406522C01
1,1.927 1.563,1.51 true 1,1.938 1.542,1.469 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc from the rear axle hub and bearing assembly.