Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM (for HV Model) › 2018.10–2019.02
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370838 PARKING SUPPORT BRAKE SYSTEM(for HV Model) U

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM(for HV Model)  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


E220917E51
3.375,0.219 3.74,0.458 0.365,0.24 3.469,0.25 3.927,0.448 0.458,0.198 10 false H4

a.

Disconnect the H4 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H4-1 (IG) - H4-28 (E) B - W-B IG power source signal Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
H4-28 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the H4 clearance warning ECU assembly connector.


d.

Measure the voltage, resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H4-2 (BOF) - H4-28 (E) R - W-B Power source for front sensor circuit
·

Power switch on (IG)

·

Parking support brake system on


11 to 14 V
H4-3 (SOF) - H4-28 (E) L - W-B Front sensor communication signal (Front clearance sonar sensor)
·

Power switch on (IG)

·

Parking support brake system on

·

Shift lever in any position other than P

·

Vehicle speed is less than approximately 10 km/h (6 mph)


Pulse generation
(Refer to waveform 1)
H4-4 (E5) - H4-28 (E) W - W-B Ground for front clearance sonar Always Below 1 Ω
H4-9 (CBZ) - H4-8 (EF) LG - L No. 1 clearance warning buzzer signal Buzzer sounding Pulse generation
(Refer to waveform 2)
H4-19 (BOR) - H4-28 (E) LG - W-B Power source for rear sensor circuit
·

Power switch on (IG)

·

Parking support brake system on


11 to 14 V
H4-20 (SOR) - H4-28 (E) SB - W-B Rear sensor communication signal (Rear clearance sonar sensor)
·

Power switch on (IG)

·

Parking support brake system on

·

Shift lever in R


Pulse generation
(Refer to waveform 3)
H4-21 (E1) - H4-28 (E) GR - W-B Ground for rear clearance sonar Always Below 1 Ω
H4-25 (BBZ) - H4-26 (ER) LG - L No. 2 clearance warning buzzer signal Buzzer sounding Pulse generation
(Refer to waveform 2)


e.

Using an oscilloscope, check waveform 1.

i.
E314893N08
0.177,0.99 0.635,1.188 0.458,0.198 10 false GND

Waveform 1 (Reference)

Item Content
Measurement terminal H4-3 (SOF) - H4-28 (E)
Measurement setting 5 V/DIV., 1 ms./DIV.
Condition
·

Power switch on (IG)

·

Parking support brake system on

·

Shift lever in any position other than P

·

Vehicle speed is less than approximately 10 km/h (6 mph)





f.

Using an oscilloscope, check waveform 2.

i.
E227014N05
0.083,1.677 0.552,1.938 0.469,0.26 10 GND

Waveform 2 (Reference)

Item Content
Measurement terminal H4-9 (CBZ) - H4-8 (EF)
H4-25 (BBZ) - H4-26 (ER)
Measurement setting 2 V/DIV., 500 μs./DIV.
Condition Buzzer sounding

HINT:

The amplitude of the waveform changes according to the set volume.




g.

Using an oscilloscope, check waveform 3.

i.
E314893N08
0.177,0.99 0.635,1.188 0.458,0.198 10 false GND

Waveform 3 (Reference)

Item Content
Measurement terminal H4-20 (SOR) - H4-28 (E)
Measurement setting 5 V/DIV., 1 ms./DIV.
Condition
·

Power switch on (IG)

·

Parking support brake system on

·

Shift lever in R








BLIND SPOT MONITOR SENSOR RH (A) (w/ Blind Spot Monitor System)


Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU


BLIND SPOT MONITOR SENSOR LH (B) (w/ Blind Spot Monitor System)


Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU