Home › Suspension › REAR SUSPENSION › REAR COIL SPRING
RM3620E _53 Suspension _076491 REAR SUSPENSION _0372234 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48738C 2.REMOVE LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Hide 89408C 3.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 48840A 4.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 5.REMOVE REAR COIL SPRING

a.
C403449C01
0.958,1.417 1.292,1.417 true 0.979,1.333 1.281,1.333 1.281,1.333 1.281,1.583 true 2.281,0.521 2.031,0.521 2.031,0.521 2.031,1.021 true 2.031,0.573 2.281,0.573 true 1.198,1.583 1.448,1.833 0.25,0.25 10 true *a 1.948,1 2.198,1.25 0.25,0.25 10 true *a
*a Matchmark


Place matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.


b.

Loosen the nut (rear suspension member sub-assembly side) of the rear No. 2 suspension arm assembly.

NOTICE:

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.



c.
C403182C01
1.75,1.833 2,1.833 false 1.917,2.25 2.167,2.25 false 2.042,1.771 2.292,2.021 0.25,0.25 10 false *a 2.208,2.188 2.542,2.438 0.333,0.25 10 false *b
*a Wooden Block
*b Jack
V100155

Wooden Block Placement Location


Using a jack and wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C403450

Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Slowly lower the rear No. 2 suspension arm assembly, and then remove the rear coil spring.


Hide 48259A 6.REMOVE REAR UPPER COIL SPRING INSULATOR

a.

Remove the rear upper coil spring insulator from the vehicle.


Hide 48258C 7.REMOVE REAR LOWER COIL SPRING INSULATOR

a.

Remove the rear lower coil spring insulator from the rear No. 2 suspension arm assembly.