Home › Drivetrain › EG62 (MANUAL TRANSMISSION / TRANSAXLE) › SHIFT LEVER ASSEMBLY
RM3620E _52 Drivetrain _076270 EG62 MANUAL TRANSMISSION / TRANSAXLE _0371317 SHIFT LEVER ASSEMBLY A

EG62 MANUAL TRANSMISSION / TRANSAXLE  SHIFT LEVER ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 33530F 1.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C406605

Install the floor shift shift lever assembly with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C406604

Attach the wire harness clamp.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the lock nut of the transmission control cable assembly 180° clockwise. While holding the lock nut in place, push in the stopper to lock the lock nut.

C406606C01
1.5,0.583 1.75,0.333 1.75,0.333 1.917,0.333 false 0.5,1.333 0.667,1.333 0.667,1.333 0.917,1.083 false 1.958,0.25 2.125,0.417 0.167,0.167 10 false *1 0.292,1.25 0.458,1.417 0.167,0.167 10 false *2
*1 Cable Lock *2 Lock Nut
V113147

Rotate approximately 180°
V113148

Push In


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable assembly will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut counterclockwise and then push in the cable lock again.



b.

Connect the outer part of the transmission control cable assembly to the floor shift shift lever assembly. Check that the stopper returns to the pulled-out position.

C406607C01
6.583,0.417 6.75,0.083 6.75,0.083 6.833,0.083 false 0.333,0.917 0.5,0.917 0.5,0.917 0.667,0.75 false 0.417,1.25 0.583,1.25 0.583,1.25 0.813,1.417 true 6.875,0 7.042,0.167 0.167,0.167 10 false *1 0.125,0.833 0.292,1 0.167,0.167 10 false *2 0.208,1.167 0.375,1.333 0.167,0.167 10 false *3
*1 Cable Lock *2 Lock Nut
*3 Floor Shift Shift Lever Assembly - -



c.
C406608C01
1.5,1.583 1.667,1.583 1.667,1.583 1.823,1.208 false 1.5,2 1.667,2 1.667,2 1.833,2.344 false 2.417,1.135 2.583,1.333 2.583,1.333 2.75,1.333 false 2.333,2.208 2.583,1.917 2.583,1.917 2.75,1.917 false 1.292,1.5 1.458,1.667 0.167,0.167 10 false *1 1.292,1.917 1.458,2.083 0.167,0.167 10 false *1 2.792,1.25 2.958,1.417 0.167,0.167 10 false *2 2.792,1.833 2.958,2 0.167,0.167 10 false *2
*1 Slider
*2 Lock Piece
V113147

Slide in this Direction
V113148

Pull Out


Slide the slider in the direction shown in the illustration and pull out the lock piece.


d.
C406609C01
1.083,1.583 0.917,1.833 0.917,1.833 0.75,1.833 true 2.917,1.167 2.833,0.917 2.833,0.917 2.667,0.917 true 0.563,1.75 0.729,1.917 0.167,0.167 10 true *1 2.479,0.833 2.646,1 0.167,0.167 10 true *2
*1 Select Control Cable
*2 Shift Control Cable


Connect the shift control cable to the floor shift shift lever assembly.


e.

Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.


f.
C406610

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



g.
C406611

Install a new clip to the select control cable.


Hide 33820B 3.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58861B 4.INSTALL NO. 1 CONSOLE BOX DUCT

a.
C406600

Connect the wire harness clamp to the No. 1 console box duct.


b.

Install the clip to the No. 1 console box duct.


Hide 58810J 5.INSTALL CONSOLE BOX ASSEMBLY