Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2018.10–2019.09
RM3620E _59 Vehicle Exterior _076526 SLIDING ROOF / CONVERTIBLE _0372465 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the map light sub-assembly (slide/tilt switch) is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure Sliding roof ECU (sliding roof drive gear sub-assembly) detects map light sub-assembly (slide/tilt switch) is stuck for 30 seconds or more
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Map light sub-assembly (slide/tilt switch)

·

Harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



PROCEDURE

1.READ VALUE USING GTS (Switch Failure)
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch Failure(Past) Open switch failure signal (Past) OFF or ON OFF: No OPEN switch on the slide switch failure signal (Past)
ON: OPEN switch on the slide switch failure signal (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past) OFF or ON OFF: No CLOSE switch on the slide switch failure signal (Past)
ON: CLOSE switch on the slide switch failure signal (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past) OFF or ON OFF: No UP switch on the tilt switch failure signal (Past)
ON: UP switch on the tilt switch failure signal (Past)
-
Down Switch Failure(Past) Down switch failure signal (Past) OFF or ON OFF: No DOWN switch on the tilt switch failure signal (Past)
ON: DOWN switch on the tilt switch failure signal (Past)
-
Open Switch Failure(Current) Open switch failure signal (Current) OFF or ON OFF: No OPEN switch on the slide switch failure signal (Current)
ON: OPEN switch on the slide switch failure signal (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current) OFF or ON OFF: No CLOSE switch on the slide switch failure signal (Current)
ON: CLOSE switch on the slide switch failure signal (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current) OFF or ON OFF: No UP switch on the tilt switch failure signal (Current)
ON: UP switch on the tilt switch failure signal (Current)
-
Down Switch Failure(Current) Down switch failure signal (Current) OFF or ON OFF: No DOWN switch on the tilt switch failure signal (Current)
ON: DOWN switch on the tilt switch failure signal (Current)
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch Failure(Past)
Close Switch Failure(Past)
Up Switch Failure(Past)
Down Switch Failure(Past)
Open Switch Failure(Current)
Close Switch Failure(Current)
Up Switch Failure(Current)
Down Switch Failure(Current)
50003 147 32,33,34,35,36,37,38,39
OK:

OFF is displayed for each Data List item.



Result:
Result Proceed to
All items are displayed "OFF" A
In part or in whole item displayed "ON" B



A

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

2.INSPECT MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)
2.INSPECT MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)
a.

Remove the map light sub-assembly (slide/tilt switch).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the map light sub-assembly (slide/tilt switch).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY] - MAP LIGHT SUB-ASSEMBLY [SLIDE/TILT SWITCH] AND BODY GROUND)

NG

REPLACE MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY] - MAP LIGHT SUB-ASSEMBLY [SLIDE/TILT SWITCH] AND BODY GROUND)
a.

Disconnect the P14 map light sub-assembly (slide/tilt switch) connector.


b.

Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-5 (UP) - P14-16 (UP) Always Below 1 Ω
P4-8 (CLS) - P14-13 (CLS) Always Below 1 Ω
P4-9 (DWN) - P14-15 (DOWN) Always Below 1 Ω
P4-10 (OPN) - P14-14 (OPN) Always Below 1 Ω
P4-2 (E) - Body ground Always Below 1 Ω
P14-11 (GND) - Body ground Always Below 1 Ω
P4-5 (UP) or P14-16 (UP) - Body ground Always 10 kΩ or higher
P4-8 (CLS) or P14-13 (CLS) - Body ground Always 10 kΩ or higher
P4-9 (DWN) or P14-15 (DOWN) - Body ground Always 10 kΩ or higher
P4-10 (OPN) or P14-14 (OPN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR