This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) has not been initialized.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2343 | Position Initialization Incomplete | Sliding roof ECU (sliding roof drive gear assembly [sliding roof]) has not been initialized. | ·
Sliding roof ECU (sliding roof drive gear assembly [sliding roof]) ·
Harness or connector |
Refer to DTC B2341.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>B2341
If the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
The panoramic moon roof system uses the CAN and LIN communication system. First, confirm that there are no malfunctions in the CAN and LIN communication system. Refer to How to Proceed with Troubleshooting.
DTC B2343 is stored in the sliding roof ECU (sliding roof drive gear assembly [sliding roof]).
If DTC B2342 and B2343 are output simultaneously, perform troubleshooting for DTC B2342 first.
Check that the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) can be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
Sliding roof ECU (sliding roof drive gear assembly [sliding roof]) can be initialized.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the panoramic moon roof auto operation.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>OPERATION CHECK
Auto operation operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
DTC B2343 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Perform the Active Test according to the display on the GTS.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding motor | OFF / Opn/Dwn / Clos/Up | - |
| Tester Display |
|---|
| Slide Roof |
Slide roof is operated using GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Read the Data List according to the display on the GTS
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Roof Open Switch | OPEN switch signal | OFF or ON | OFF: Slide switch (OPEN) on the slide switch not pressed
ON: Slide switch (OPEN) on the slide switch pressed |
- |
| Roof Close Switch | CLOSE switch signal | OFF or ON | OFF: Slide switch (CLOSE) on the slide switch not pressed
ON: Slide switch (CLOSE) on the slide switch pressed |
- |
| Tester Display |
|---|
| Roof Open Switch |
| Roof Close Switch |
The GTS display changes according to switch operation as shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
NG
Remove the map light sub-assembly.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the map light sub-assembly.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly [sliding roof]) connector.
Disconnect the P14 map light sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P4-4 (TILT) - P14-17 (B) | Always | Below 1 Ω |
| P4-5 (UP) - P14-16 (UP) | Always | Below 1 Ω |
| P4-8 (CLS) - P14-13 (CLS) | Always | Below 1 Ω |
| P4-9 (DWN) - P14-15 (DOWN) | Always | Below 1 Ω |
| P4-10 (OPN) - P14-14 (OPN) | Always | Below 1 Ω |
| P4-2 (E) - Body ground | Always | Below 1 Ω |
| P14-11 (GND) - Body ground | Always | Below 1 Ω |
| P4-4 (TILT) or P14-17 (B) - Body ground | Always | 10 kΩ or higher |
| P4-5 (UP) or P14-16 (UP) - Body ground | Always | 10 kΩ or higher |
| P4-8 (CLS) or P14-13 (CLS) - Body ground | Always | 10 kΩ or higher |
| P4-9 (DWN) or P14-15 (DOWN) - Body ground | Always | 10 kΩ or higher |
| P4-10 (OPN) - P14-14 (OPN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
NG