Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3620E _59 Vehicle Exterior _076564 WIPER / WASHER _0372553 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1373  Lost Communication with Wiper System LIN BUS  


DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the windshield wiper motor assembly and rain sensor via LIN communication. If a malfunction occurs in the LIN communication line and a communication error occurs, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1373 Lost Communication with Wiper System LIN BUS
DTC Detection Condition:

Ignition switch ON (IG+ voltage 9.5 V or higher)


Malfunction Status:

Wire-type LIN communication error detected


Malfunction Duration:

7 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body

WIRING DIAGRAM

E404590E02
1.542,1.531 2,1.729 0.458,0.198 10 false P6 1.552,1.708 2.396,1.917 0.844,0.208 10 false Rain Sensor 4.26,1.521 4.719,1.719 0.458,0.198 10 false G43 4.26,1.708 5.906,2.146 1.646,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 2.208,0.875 2.667,1.073 0.458,0.198 10 false MPX 2.656,0.708 2.813,0.906 0.156,0.198 10 false 3 4.365,0.708 4.521,0.906 0.156,0.198 10 false 3 4.604,0.885 5.219,1.083 0.615,0.198 10 false LIN3 0.542,2.427 2.188,2.635 1.646,0.208 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Turn the ignition switch to ON and wait for at least 10 seconds.


c.

Check for DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1373 is not output



Result:
Proceed to
OK
NG



OK

NG

2.CHECK RAIN SENSOR
2.CHECK RAIN SENSOR
a.

Disconnect the P6 rain sensor connector.


b.

Clear the DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the ignition switch to ON and wait for at least 10 seconds.


d.

Check for DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B1373 is not output, but DTC B1279 is output A
DTC B1373 is output B



A

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR AND BODY GROUND)
a.

Disconnect the G43 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the P6 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G43-3 (LIN3) - P6-3 (MPX) Always Below 1 Ω
G43-3 (LIN3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR