Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3620E _59 Vehicle Exterior _076564 WIPER / WASHER _0372553 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B2357  Lost Communication with Wiper Module  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B2357 Lost Communication with Wiper Module
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly


Malfunction Time:

10 seconds or more


·

Windshield wiper relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Windshield wiper relay (WIPER)


○ Main Body

WIRING DIAGRAM

E404615E03
0.479,4.552 1.583,5.021 1.104,0.469 10 false Windshield Wiper Relay Assembly 0.802,5.396 2.542,5.635 1.74,0.24 10 false : CXPI Communication Line 1.313,1.021 1.625,1.219 0.313,0.198 10 false +B 1.135,2.875 1.75,3.073 0.615,0.198 10 false MPX1 1.323,4.042 1.625,4.26 0.302,0.219 10 false ES 1.385,3.469 1.542,3.667 0.156,0.198 10 false E 1.688,1 2.146,1.198 0.458,0.198 10 false A5 1.698,2.865 2.156,3.063 0.458,0.198 10 false A6 1.719,4.042 2.177,4.24 0.458,0.198 10 false A6 1.708,3.448 2.167,3.646 0.458,0.198 10 false A5 1.75,0.781 2.063,0.979 0.313,0.198 10 false 8 1.75,2.646 1.906,2.844 0.156,0.198 10 false 4 1.75,3.229 1.906,3.427 0.156,0.198 10 false 3 1.76,3.823 2.073,4.021 0.313,0.198 10 false 5 4.021,1.156 4.792,1.354 0.771,0.198 10 false WIPER 3.042,0.24 4.448,0.531 1.406,0.292 10 false from Auxiliary Battery 5.094,1.333 5.552,1.531 0.458,0.198 10 false G44 5.083,2.865 5.542,3.063 0.458,0.198 10 false G45 5.135,1.135 5.448,1.333 0.313,0.198 10 false 21 5.156,2.646 5.313,2.844 0.156,0.198 10 false 5 5.49,1.24 5.948,1.438 0.458,0.198 10 false WPS 5.479,2.865 5.938,3.063 0.458,0.198 10 false CXP1 5.344,4 6.99,4.396 1.646,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 6.083,0.646 6.396,0.844 0.313,0.198 10 false IG 6.438,0.656 6.594,0.854 0.156,0.198 10 false B 2.583,1.708 3.698,2.094 1.115,0.385 10 false Windshield Wiper Relay (WIPER) 2.688,0.885 2.844,1.083 0.156,0.198 10 false 3 2.688,1.229 2.844,1.427 0.156,0.198 10 false 2 3.531,0.896 3.688,1.094 0.156,0.198 10 false 5 3.531,1.229 3.688,1.427 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse of circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the A6 windshield wiper relay assembly connector.


b.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-4 (MPX1) - G45-5 (CXP1) Always Below 1 Ω
A6-4 (MPX1) or G45-5 (CXP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E404616C02
1.521,0.323 1.896,0.552 0.375,0.229 2.083,1.208 2.375,0.406 2.375,0.406 2.573,0.406 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.594,0.354 2.052,0.552 0.458,0.198 10 false G45 2.646,0.323 3.063,0.531 0.417,0.208 10 false CXP1
*a Component without harness connected
(Main Body ECU [Multiplex Network Body ECU])


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G45-5 (CXP1) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)

NG

3.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wiper Power Relay Operates the windshield wiper relay (WIPER) OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Wiper Power Relay
50004 123 76
OK:

Windshield wiper relay (WIPER) operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

NG

9.INSPECT WINDSHIELD WIPER RELAY (WIPER)
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)
E410610C02
2.427,0.115 2.75,0.323 0.323,0.208 4.521,0.115 4.844,0.323 0.323,0.208 3.292,0.458 3.073,0.458 3.073,0.458 2.625,0.948 true 4.406,1.25 4.073,1.469 4.073,1.469 3.854,1.469 true 2.51,0.135 2.823,0.333 0.313,0.198 10 false A5 4.594,0.135 4.906,0.333 0.313,0.198 10 false A6 3.385,0.365 3.542,0.563 0.156,0.198 10 false E 3.594,1.385 3.906,1.583 0.313,0.198 10 false ES 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Windshield Wiper Relay Assembly)
- -


a.

Disconnect the windshield wiper relay assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-3 (E) - Body ground Always Below 1 Ω
A6-5 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY)
a.
E410611C01
1.542,0.198 1.906,0.458 0.365,0.26 2.052,1.458 2.479,1.125 2.479,1.125 2.708,1.125 true 1.625,0.24 1.938,0.438 0.313,0.198 10 false A5 2.792,1.021 3.104,1.219 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Windshield Wiper Relay Assembly)


Disconnect the windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-8 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds or more after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

6.INSPECT WINDSHIELD WIPER RELAY (WIPER)
6.INSPECT WINDSHIELD WIPER RELAY (WIPER)
a.

Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Inspect the windshield wiper relay (WIPER).

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - BATTERY)

NG

REPLACE WINDSHIELD WIPER RELAY (WIPER)

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - BATTERY)
a.
B472073C21
0.094,0.042 0.406,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Windshield Wiper Relay [WIPER])


Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block.


b.

Disconnect the A5 windshield wiper relay assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Windshield wiper relay (WIPER) terminal 5 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - WINDSHIELD WIPER RELAY ASSEMBLY BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - WINDSHIELD WIPER RELAY ASSEMBLY BODY GROUND)
a.

Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block.


b.

Disconnect the A5 windshield wiper relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-8 (+B) - Windshield wiper relay (WIPER) terminal 3 Always Below 1 Ω
A5-8 (+B) or Windshield wiper relay (WIPER) terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WINDSHIELD WIPER RELAY (WIPER)
a.

Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Inspect the windshield wiper relay (WIPER).

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE WINDSHIELD WIPER RELAY (WIPER)

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block assembly.


b.

Disconnect the G44 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield wiper relay (WIPER) terminal 1 - G44-21 (WPS) Always Below 1 Ω
Windshield wiper relay (WIPER) terminal 1 or G44-21 (WPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER] - BODY GROUND)
a.
B472073C21
0.094,0.042 0.406,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Windshield Wiper Relay [WIPER])


Remove the windshield wiper relay (WIPER) from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield wiper relay (WIPER) terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR