Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3620E _59 Vehicle Exterior _076564 WIPER / WASHER _0372553 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the washer fluid level is lower than a certain level, a warning message is displayed on the combination meter assembly.

WIRING DIAGRAM

E404747E05
2.063,1.625 2.375,1.823 0.313,0.198 10 false A3 2.052,1.792 4.031,2.115 1.979,0.323 10 false Level Warning Switch Assembly 2.146,1.01 2.302,1.208 0.156,0.198 10 false 2 2.365,1.01 2.521,1.208 0.156,0.198 10 false E 3.615,1 3.771,1.198 0.156,0.198 10 false S 3.833,1 3.99,1.198 0.156,0.198 10 false 1 4.75,1 5.063,1.198 0.313,0.198 10 false 14 4.646,2.083 5.104,2.281 0.458,0.198 10 false G19 4.646,2.25 6.531,2.479 1.885,0.229 10 false Combination Meter Assembly 5.031,1.01 5.646,1.208 0.615,0.198 10 false WLVL 5.708,0.521 6.021,0.719 0.313,0.198 10 false IG

PROCEDURE

1.READ VALUE USING GTS (WASHER LEVEL WARNING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Washer Level Warning Switch Windshield washer JAR assembly (Level warning switch) state OFF or ON ON: Washer fluid level low
OFF: Washer fluid level not low
-
Body Electrical > Combination Meter > Data List
Tester Display
Washer Level Warning Switch
50003 409 25
OK:

The GTS display changes correctly in response to the washer fluid level.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK LEVEL WARNING SWITCH ASSEMBLY
2.CHECK LEVEL WARNING SWITCH ASSEMBLY
a.

Disconnect the A3 level warning switch assembly connector.


b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE LEVEL WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A3 level warning switch assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-1 (S) - G19-14 (WLVL) Always Below 1 Ω
A3-2 (E) - Body ground Always Below 1 Ω
A3-1 (S) or G19-14 (WLVL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR