Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3620E _59 Vehicle Exterior _076564 WIPER / WASHER _0372553 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Nozzle Heater Circuit  


DESCRIPTION

The washer nozzle sub-assembly controls the main body ECU and operates the washer nozzle sub-assembly according to the ambient temperature.

WIRING DIAGRAM

E405259E01
0.344,4.406 1.833,4.635 1.49,0.229 10 false from Auxiliary Battery 2.156,4.573 3.323,4.771 1.167,0.198 10 false WASH NZL HTR 0.365,5.135 1.708,5.365 1.344,0.229 10 false from IG1 NO.1 Relay 2.198,5.313 3.208,5.521 1.01,0.208 10 false ECU-IG1 NO.3 3.01,5.677 4.615,6.042 1.604,0.365 10 false Windshield Washer Relay (WASH NZL HTR) 5.271,5.052 5.427,5.25 0.156,0.198 10 false 2 5.198,5.885 5.656,6.083 0.458,0.198 10 false G43 5.198,6.052 6.844,6.406 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,5.052 6.083,5.25 0.615,0.198 10 false WHTR 4.156,5.063 4.313,5.26 0.156,0.198 10 false 2 3.292,5.063 3.448,5.26 0.156,0.198 10 false 1 3.292,4.313 3.448,4.51 0.156,0.198 10 false 5 4.146,4.313 4.302,4.51 0.156,0.198 10 false 3 3.479,3.271 5.104,3.677 1.625,0.406 10 false No. 1 Windshield Washer (Front Joint to Joint) Hose 3.479,3.094 3.906,3.271 0.427,0.177 10 false A13 5.302,0.406 5.458,0.604 0.156,0.198 10 false B 4.885,0.406 5.042,0.604 0.156,0.198 10 false B 5.323,2.469 5.479,2.667 0.156,0.198 10 false E 4.875,2.469 5.031,2.667 0.156,0.198 10 false E 5.573,0.396 5.729,0.594 0.156,0.198 10 false 2 4.646,0.396 4.802,0.594 0.156,0.198 10 false 2 5.563,2.469 5.719,2.667 0.156,0.198 10 false 1 4.646,2.469 4.802,2.667 0.156,0.198 10 false 1 0.813,1.344 2.708,1.74 1.896,0.396 10 false Washer Nozzle Sub-assembly (for LH Side) 0.813,3.135 2.719,3.5 1.906,0.365 10 false Washer Nozzle Sub-assembly (for RH Side) 0.833,1.177 0.99,1.375 0.156,0.198 10 false A 0.813,2.969 0.969,3.167 0.156,0.198 10 false B 2.927,0.385 3.083,0.583 0.156,0.198 10 false 2 2.938,2.156 3.094,2.354 0.156,0.198 10 false 2 2.927,2.479 3.083,2.677 0.156,0.198 10 false 1 2.927,0.698 3.083,0.896 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to the Service Bulletin.

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (WASHER NOZZLE HEATER)
a.

Disconnect the A13 No. 1 windshield washer (front joint to joint) hose connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Washer Nozzle Heater Washer nozzle heater operation OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Washer Nozzle Heater
50004 123 73

g.
E405480C01
1.458,0.104 1.854,0.365 0.396,0.26 2.104,1.042 2.51,0.208 2.51,0.208 2.729,0.208 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.531,0.146 1.99,0.344 0.458,0.198 10 false G43 2.813,0.125 3.313,0.344 0.5,0.219 10 false WHTR
*a Component with harness connected
Main Body ECU (Multiplex Network Body ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-2 (WHTR) - Body ground Ignition switch ON, Active Test is not performed 11 to 14 V
Ignition switch ON, Active Test is performed Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE - BODY GROUND)

NG

5.INSPECT WINDSHIELD WASHER RELAY (WASH NZL HTR)
2.CHECK HARNESS AND CONNECTOR (NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE - BODY GROUND)
a.
E410616C01
1.49,0.146 1.906,0.396 0.417,0.25 1.917,1.427 2.49,0.896 2.49,0.896 2.708,0.896 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 1.563,0.177 2.021,0.375 0.458,0.198 10 false A13 2.802,0.802 2.958,1 0.156,0.198 10 false E
*a Front view of wire harness connector
(to No. 1 Windshield Washer [Front Joint to Joint] Hose)


Disconnect the No. 1 windshield washer (front joint to joint) hose connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY
a.

Remove the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>REMOVAL


b.

Inspect the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE

NG

REPLACE WASHER NOZZLE SUB-ASSEMBLY

4.INSPECT NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE
a.

Remove the No. 1 windshield washer (front joint to joint) hose.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (B) - A-2 Always Below 1 Ω
A13-2 (B) - B-2 Always Below 1 Ω
A13-2 (B), A-2 or B-2 - Body ground Always 10 kΩ or higher
A13-1 (E) - A-1 Always Below 1 Ω
A13-1 (E) - B-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE

5.INSPECT WINDSHIELD WASHER RELAY (WASH NZL HTR)
a.

Remove the windshield washer relay (WASH NZL HTR) from the No. 2 engine room relay block assembly.


b.

Inspect the windshield washer relay (WASH NZL HTR).

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY (WASH NZL HTR) - BATTERY)

NG

REPLACE WINDSHIELD WASHER RELAY (WASH NZL HTR)

6.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY (WASH NZL HTR) - BATTERY)
a.
E409904C02
0.094,0.042 0.406,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Windshield Washer Relay [WASH NZL HTR])


Remove the windshield washer relay (WASH NZL HTR) from the No. 2 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Windshield washer relay (WASH NZL HTR) terminal 5 - Body ground Ignition switch off 11 to 14 V
Windshield washer relay (WASH NZL HTR) terminal 1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WASHER RELAY (WASH NZL HTR) - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WASHER RELAY (WASH NZL HTR) - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Remove the windshield washer relay (WASH NZL HTR) from the No. 2 engine room relay block assembly.


b.

Disconnect the G36 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield washer relay (WASH NZL HTR) terminal 2 - G43-2 (WHTR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WASH NZL HTR] - NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER RELAY [WASH NZL HTR] - NO. 1 WINDSHIELD WASHER [FRONT JOINT TO JOINT] HOSE)
a.

Remove the windshield washer relay (WASH NZL HTR) from the No. 2 engine room relay block assembly.


b.

Disconnect the A13 No. 1 windshield washer (front joint to joint) hose connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield washer relay (WASH NZL HTR) terminal 3 - A13-2 (B) Always Below 1 Ω
Windshield washer relay (WASH NZL HTR) terminal 3 or A13-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR