Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372800 SFI SYSTEM C

M20A-FKS ENGINE CONTROL  SFI SYSTEM  P061512  Starter Relay Circuit Short to Battery  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery All of the following conditions are met, and battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Starter relay

·

Park/neutral position switch assembly (for continuously variable transaxle models)

·

Clutch pedal switch assembly (for manual transaxle models)

·

Starter relay circuit

·

TCM (for continuously variable transaxle models)

·

ECM


Comes on DTC stored SAE: P0617

MONITOR STRATEGY

Required Sensors/Components (Main) Starter relay (ST)
Park/neutral position switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A428845E01
1.063,0.844 1.708,1.083 0.646,0.24 10 false 24 km/h 1.333,1.958 1.979,2.198 0.646,0.24 10 false Idling 0.531,2.229 1.729,2.479 1.198,0.25 10 false Ignition Switch ON 2.385,2.885 3.031,3.281 0.646,0.396 10 false 5 seconds or more 3.583,2.938 4.875,3.229 1.292,0.292 10 false 20 seconds or more 2.625,2.094 2.979,2.365 0.354,0.271 10 false [B] 2.01,2.333 2.365,2.604 0.354,0.271 10 false [A] 4.073,0.448 4.427,0.719 0.354,0.271 10 false [C] 4.885,3.302 5.24,3.573 0.354,0.271 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 5 seconds or more [B].

10.

Drive the vehicle at a speed of 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P061512.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [C] through [D] again.




WIRING DIAGRAM

A434318E01
0.073,0.063 6.396,0.302 6.323,0.24 12 false w/ Stop and Start System for Continuously Variable Transaxle Models: 0.271,2.042 0.667,2.24 0.396,0.198 10 false A34 0.26,2.188 2.198,2.385 1.938,0.198 10 false Engine Stop and Start ECU 1.323,0.667 1.719,0.865 0.396,0.198 10 false NE 1.177,1.063 1.573,1.26 0.396,0.198 10 false STA2 1.281,1.438 1.677,1.635 0.396,0.198 10 false CLL 1.25,1.74 1.646,1.938 0.396,0.198 10 false STA 1.604,0.573 2,0.771 0.396,0.198 10 false 10 1.625,0.927 2.021,1.125 0.396,0.198 10 false 23 1.635,1.302 2.031,1.5 0.396,0.198 10 false 17 1.635,1.625 2.031,1.823 0.396,0.198 10 false 21 6.281,1.719 6.677,1.917 0.396,0.198 10 false A24 6.271,1.875 6.667,2.073 0.396,0.198 10 false ECM 6.031,0.667 6.427,0.865 0.396,0.198 10 false NEO 6.031,1.052 6.427,1.25 0.396,0.198 10 false STA 6.031,1.438 6.427,1.635 0.396,0.198 10 false NSW 5.74,0.552 6.135,0.75 0.396,0.198 10 false 16 5.75,0.927 6.146,1.125 0.396,0.198 10 false 30 5.75,1.313 6.146,1.51 0.396,0.198 10 false 23 0.031,4.115 0.427,4.313 0.396,0.198 10 false A15 0.01,4.292 2.927,4.552 2.917,0.26 10 false Certification ECU (Smart Key ECU Assembly)*1 1.323,2.906 1.719,3.104 0.396,0.198 10 false NE 1.167,3.365 1.563,3.563 0.396,0.198 10 false STAR 1.25,3.854 1.646,4.052 0.396,0.198 10 false STA 1.635,2.771 2.031,2.969 0.396,0.198 10 false 16 1.667,3.229 2.063,3.427 0.396,0.198 10 false 9 1.667,3.729 2.063,3.927 0.396,0.198 10 false 20 3.563,4.125 3.958,4.323 0.396,0.198 10 false C31 3.563,4.292 5.375,4.76 1.813,0.469 10 false Park/Neutral Position Switch Assembly 0.688,5.031 1.083,5.229 0.396,0.198 10 false AM2 1.302,5.323 3.24,5.521 1.938,0.198 10 false Ignition Switch Assembly*2 1.292,5.177 1.688,5.375 0.396,0.198 10 false G28 1.625,4.771 2.021,4.969 0.396,0.198 10 false AM1 2.229,4.771 2.625,4.969 0.396,0.198 10 false ST1 1.427,4.76 1.823,4.958 0.396,0.198 10 false 7 2.594,4.75 2.99,4.948 0.396,0.198 10 false 5 3.99,6.604 4.385,6.802 0.396,0.198 10 false C43 4.188,6.917 5.396,7.26 1.208,0.344 10 false Starter Assembly 2.563,6.531 3.333,6.729 0.771,0.198 10 false ST NO. 1 2.563,7.719 3.417,8 0.854,0.281 10 false ST NO. 2 1.188,7.167 2.042,7.448 0.854,0.281 10 false ST NO. 2 0.542,8.125 1.396,8.406 0.854,0.281 10 false Battery 4.479,7.958 6.917,8.302 2.438,0.344 10 false *1: w/ Entry and Start System 4.479,8.302 6.917,8.646 2.438,0.344 10 false *2: w/o Entry and Start System 2.406,2.771 2.802,2.969 0.396,0.198 10 false *1 2.396,3.26 2.792,3.458 0.396,0.198 10 false *1 2.385,3.729 2.781,3.927 0.396,0.198 10 false *1 2.76,4.781 3.156,4.979 0.396,0.198 10 false *2 4.823,3.729 5.219,3.927 0.396,0.198 10 false 4 3.719,3.74 4.115,3.938 0.396,0.198 10 false 5 4.583,3.75 4.979,3.948 0.396,0.198 10 false B 3.927,3.74 4.323,3.938 0.396,0.198 10 false L 3.188,5.76 3.583,5.958 0.396,0.198 10 false 3 3.208,6.885 3.604,7.083 0.396,0.198 10 false 3 3.188,6.135 3.583,6.333 0.396,0.198 10 false 2 3.198,7.292 3.594,7.49 0.396,0.198 10 false 2 2.375,5.76 2.771,5.958 0.396,0.198 10 false 5 2.385,6.885 2.781,7.083 0.396,0.198 10 false 5 2.375,6.135 2.771,6.333 0.396,0.198 10 false 1 2.375,7.292 2.771,7.49 0.396,0.198 10 false 1 4.063,5.688 4.458,5.885 0.396,0.198 10 false 2 4.052,6.427 4.448,6.625 0.396,0.198 10 false 1 4.302,6.615 4.698,6.813 0.396,0.198 10 false SL2 4.302,5.875 4.698,6.073 0.396,0.198 10 false SL1 6.271,3.365 6.667,3.563 0.396,0.198 10 false C33 6.271,3.521 6.667,3.719 0.396,0.198 10 false TCM 6.063,2.448 6.458,2.646 0.396,0.198 10 false STA 5.781,2.323 6.177,2.521 0.396,0.198 10 false 28 0.385,5.563 1.24,5.844 0.854,0.281 10 false J/B-B 1.167,6.042 1.938,6.24 0.771,0.198 10 false ST NO. 1 3.99,5.875 4.385,6.073 0.396,0.198 10 false C43 6.063,2.896 6.458,3.094 0.396,0.198 10 false NE 4.021,6.24 4.417,6.438 0.396,0.198 10 false D1 4.052,6.063 4.448,6.26 0.396,0.198 10 false 1 4.323,6.25 4.719,6.448 0.396,0.198 10 false B 5.792,2.771 6.188,2.969 0.396,0.198 10 false 43

A434319E01
0.063,0.01 5.198,0.25 5.135,0.24 12 false w/ Stop and Start System for Manual Transaxle Models: 6.042,0.656 6.5,0.854 0.458,0.198 10 false NEO 6.031,1.125 6.49,1.323 0.458,0.198 10 false STA 6.323,1.74 6.781,1.938 0.458,0.198 10 false A24 6.323,1.906 6.781,2.104 0.458,0.198 10 false ECM 5.802,0.583 6.115,0.781 0.313,0.198 10 false 16 5.802,1.01 6.115,1.208 0.313,0.198 10 false 30 1.323,0.688 1.635,0.885 0.313,0.198 10 false NE 1.635,0.594 1.948,0.792 0.313,0.198 10 false 10 1.281,1.115 1.74,1.313 0.458,0.198 10 false CLL 1.635,1.021 1.948,1.219 0.313,0.198 10 false 17 1.25,1.552 1.708,1.75 0.458,0.198 10 false STA 1.635,1.448 1.948,1.646 0.313,0.198 10 false 21 0.469,2.01 0.927,2.208 0.458,0.198 10 false A34 0.458,2.188 4.281,2.385 3.823,0.198 10 false Engine Stop and Start ECU 1.323,2.708 1.635,2.906 0.313,0.198 10 false NE 1.156,3.667 1.771,3.865 0.615,0.198 10 false STAR 1.25,3.198 1.708,3.396 0.458,0.198 10 false STA 1.615,2.615 1.927,2.813 0.313,0.198 10 false 16 1.656,3.052 1.906,3.271 0.25,0.219 10 false 20 1.656,3.542 1.813,3.74 0.156,0.198 10 false 9 3.906,3.979 4.219,4.177 0.313,0.198 10 false A81 3.896,4.156 5.792,4.385 1.896,0.229 10 false Clutch Start Switch Assembly 5.115,3.573 5.271,3.771 0.156,0.198 10 false 1 4.073,3.573 4.229,3.771 0.156,0.198 10 false 2 0.073,4.01 0.531,4.208 0.458,0.198 10 false A15 0.042,4.198 6.771,4.396 6.729,0.198 10 false Certification ECU (Smart Key ECU Assembly)*1 2.135,2.594 2.448,2.792 0.313,0.198 10 false *1 2.125,3.083 2.438,3.281 0.313,0.198 10 false *1 2.115,3.573 2.427,3.771 0.313,0.198 10 false *1 2.823,4.781 3.135,4.979 0.313,0.198 10 false *2 2.563,4.802 2.719,5 0.156,0.198 10 false 5 2.229,4.781 2.688,4.979 0.458,0.198 10 false ST1 1.625,4.792 2.083,4.99 0.458,0.198 10 false AM1 1.479,4.781 1.635,4.979 0.156,0.198 10 false 7 1.385,5.188 1.698,5.385 0.313,0.198 10 false G28 1.417,5.354 5.396,5.552 3.979,0.198 10 false Ignition Switch Assembly*2 0.698,5.042 1.156,5.24 0.458,0.198 10 false AM2 2.563,6.552 3.635,6.75 1.073,0.198 10 false ST NO. 1 4.948,6.854 5.26,7.052 0.313,0.198 10 false C43 4.26,7.198 4.573,7.396 0.313,0.198 10 false D1 5.281,6.844 5.438,7.042 0.156,0.198 10 false 2 4.292,7 4.448,7.198 0.156,0.198 10 false 1 4.26,8.021 6.708,8.219 2.448,0.198 10 false Starter Assembly 0.552,8.104 1.625,8.302 1.073,0.198 10 false Battery 1.771,7.583 3.688,7.802 1.917,0.219 10 false *1: w/ Entry and Start System 1.771,8.031 3.719,8.281 1.948,0.25 10 false *2: w/o Entry and Start System 2.417,5.781 2.573,5.979 0.156,0.198 10 false 5 3.156,5.792 3.313,5.99 0.156,0.198 10 false 3 2.417,6.167 2.573,6.365 0.156,0.198 10 false 1 3.156,6.177 3.313,6.375 0.156,0.198 10 false 2 0.385,5.563 1.458,5.76 1.073,0.198 10 false J/B-B 1.167,6.063 1.958,6.292 0.792,0.229 10 false ST NO. 1 4.573,7.083 4.885,7.281 0.313,0.198 10 false B 5.115,7.073 5.427,7.271 0.313,0.198 10 false SL1

A434320E01
0.188,1.823 0.667,2.063 0.479,0.24 10 false A15 0.188,2.01 1.708,2.448 1.521,0.438 10 false Certification ECU (Smart Key ECU Assembly)*1 3.042,1.865 3.521,2.104 0.479,0.24 10 false C31 3.052,2.042 4.365,2.427 1.313,0.385 10 false Park/Neutral Position Switch Assembly 1.583,0.594 2.063,0.833 0.479,0.24 10 false 16 1.646,1.042 2.125,1.281 0.479,0.24 10 false 9 1.635,1.448 2.115,1.688 0.479,0.24 10 false 20 1.292,0.708 1.771,0.948 0.479,0.24 10 false NE 1.125,1.156 1.604,1.396 0.479,0.24 10 false STAR 1.198,1.552 1.677,1.792 0.479,0.24 10 false STA 0.104,0.073 6.156,0.375 6.052,0.302 12 false w/o Stop and Start System for Continuously Variable Transaxle Models: 5.854,0.708 6.333,0.948 0.479,0.24 10 false NEO 5.854,1.167 6.333,1.406 0.479,0.24 10 false NSW 5.583,0.583 6.063,0.823 0.479,0.24 10 false 16 5.604,1.042 6.083,1.281 0.479,0.24 10 false 23 5.823,4.198 6.302,4.438 0.479,0.24 10 false STA 5.573,4.198 6.052,4.438 0.479,0.24 10 false 30 6.188,5.198 6.667,5.438 0.479,0.24 10 false A24 6.177,5.354 6.604,5.594 0.427,0.24 10 false ECM 6.24,7.198 6.719,7.438 0.479,0.24 10 false C33 6.25,7.365 6.729,7.604 0.479,0.24 10 false TCM 5.573,6.49 6.052,6.729 0.479,0.24 10 false 28 5.573,5.948 6.052,6.188 0.479,0.24 10 false 43 2.938,4.979 3.625,5.229 0.688,0.25 10 false ST NO. 1 2.688,5.5 3.167,5.74 0.479,0.24 10 false 1 2.156,5.49 2.635,5.729 0.479,0.24 10 false 3 1.698,5.927 2.177,6.167 0.479,0.24 10 false C42 0.979,6.292 1.458,6.531 0.479,0.24 10 false D2 0.552,7.042 1.031,7.281 0.479,0.24 10 false Battery 1.354,7.104 2,7.573 0.646,0.469 10 false Starter Assembly 5.833,6.646 6.313,6.885 0.479,0.24 10 false STA 5.833,6.104 6.313,6.344 0.479,0.24 10 false NE 3.167,1.458 3.646,1.698 0.479,0.24 10 false 5 4.073,1.458 4.552,1.698 0.479,0.24 10 false 4 3.854,1.469 4.333,1.708 0.479,0.24 10 false B 3.375,1.469 3.854,1.708 0.479,0.24 10 false L 2.177,4.51 2.656,4.75 0.479,0.24 10 false 5 2.698,4.5 3.177,4.74 0.479,0.24 10 false 2 2.083,5.896 2.563,6.135 0.479,0.24 10 false 1 1.031,6.083 1.51,6.323 0.479,0.24 10 false 1 2.052,0.594 2.531,0.833 0.479,0.24 10 false *1 2.042,1.042 2.521,1.281 0.479,0.24 10 false *1 2.021,1.448 2.5,1.688 0.479,0.24 10 false *1 0.552,3.156 1.031,3.396 0.479,0.24 10 false AM2 0.375,3.927 0.854,4.167 0.479,0.24 10 false J/B-B 1.063,3.344 1.542,3.583 0.479,0.24 10 false G28 1.073,3.5 2,3.938 0.927,0.438 10 false Ignition Switch Assembly*2 2.104,2.125 2.583,2.365 0.479,0.24 10 false *2 2.063,2.854 2.292,3.083 0.229,0.229 10 false 5 0.917,2.844 1.052,3.083 0.135,0.24 10 false 7 1.125,2.865 1.479,3.094 0.354,0.229 10 false AM1 1.688,2.865 2.042,3.094 0.354,0.229 10 false ST1 2.958,6.948 4.99,7.323 2.031,0.375 10 false *1: w/ Entry and Start System 2.958,7.313 4.99,7.688 2.031,0.375 10 false *2: w/o Entry and Start System 0.417,4.5 1.104,4.75 0.688,0.25 10 false ST NO. 1 1.365,6.146 1.844,6.385 0.479,0.24 10 false B 1.906,6.135 2.385,6.375 0.479,0.24 10 false ST

A434321E01
0.188,1.823 0.667,2.063 0.479,0.24 10 false A15 0.188,2.01 1.708,2.448 1.521,0.438 10 false Certification ECU (Smart Key ECU Assembly)*1 3.042,1.865 3.521,2.104 0.479,0.24 10 false A81 3.052,2.042 5.063,2.427 2.01,0.385 10 false Clutch Start Switch Assembly 1.583,0.594 2.063,0.833 0.479,0.24 10 false 16 1.646,1.042 2.125,1.281 0.479,0.24 10 false 9 1.635,1.448 2.115,1.688 0.479,0.24 10 false 20 1.292,0.708 1.771,0.948 0.479,0.24 10 false NE 1.125,1.156 1.604,1.396 0.479,0.24 10 false STAR 1.198,1.552 1.677,1.792 0.479,0.24 10 false STA 0.104,0.073 6.156,0.375 6.052,0.302 12 false w/o Stop and Start System for Manual Transaxle Models: 5.854,0.708 6.333,0.948 0.479,0.24 10 false NEO 5.583,0.583 6.063,0.823 0.479,0.24 10 false 16 5.823,4.198 6.302,4.438 0.479,0.24 10 false STA 5.573,4.198 6.052,4.438 0.479,0.24 10 false 30 6.188,5.198 6.667,5.438 0.479,0.24 10 false A24 6.177,5.354 6.604,5.594 0.427,0.24 10 false ECM 2.938,4.969 3.667,5.198 0.729,0.229 10 false ST NO. 1 2.688,5.5 3.167,5.74 0.479,0.24 10 false 1 2.156,5.49 2.635,5.729 0.479,0.24 10 false 3 1.698,5.927 2.177,6.167 0.479,0.24 10 false C42 0.99,6.292 1.469,6.531 0.479,0.24 10 false D2 0.552,7.042 1.031,7.281 0.479,0.24 10 false Battery 1.354,7.104 2,7.573 0.646,0.469 10 false Starter Assembly 3.156,1.458 3.635,1.698 0.479,0.24 10 false 1 4.073,1.458 4.552,1.698 0.479,0.24 10 false 2 2.177,4.51 2.656,4.75 0.479,0.24 10 false 5 2.698,4.51 3.177,4.75 0.479,0.24 10 false 2 2.083,5.896 2.563,6.135 0.479,0.24 10 false 1 1.031,6.083 1.51,6.323 0.479,0.24 10 false 1 2.052,0.594 2.531,0.833 0.479,0.24 10 false *1 2.042,1.042 2.521,1.281 0.479,0.24 10 false *1 2.021,1.448 2.5,1.688 0.479,0.24 10 false *1 0.552,3.156 1.031,3.396 0.479,0.24 10 false AM2 0.375,3.927 0.854,4.167 0.479,0.24 10 false J/B-B 1.063,3.333 1.542,3.573 0.479,0.24 10 false G28 1.073,3.5 2,3.938 0.927,0.438 10 false Ignition Switch Assembly*2 2.104,2.125 2.583,2.365 0.479,0.24 10 false *2 2.063,2.854 2.292,3.083 0.229,0.229 10 false 5 0.917,2.844 1.052,3.083 0.135,0.24 10 false 7 1.125,2.865 1.479,3.094 0.354,0.229 10 false AM1 1.688,2.865 2.042,3.094 0.354,0.229 10 false ST1 3.698,6.927 5.823,7.323 2.125,0.396 10 false *1: w/ Entry and Start System 3.708,7.313 5.833,7.708 2.125,0.396 10 false *2: w/o Entry and Start System 1.375,6.135 1.854,6.375 0.479,0.24 10 false B 1.885,6.135 2.365,6.375 0.479,0.24 10 false ST 0.427,4.479 1.156,4.708 0.729,0.229 10 false ST NO. 1

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.READ VALUE USING GTS (STARTER SW)

B

15.READ VALUE USING GTS (STARTER SW)
2.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter SW
Ignition switch ON OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch to ON, GTS connected and Data List item "Starter SW" selected.


Result:
Result Proceed to
OK A
NG (for Continuously Variable Transaxle Models) B
NG (for Manual Transaxle Models) C


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



A

B

3.INSPECT ST NO. 2 RELAY (CHECK FOR SHORT CIRCUIT)

C

9.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
3.INSPECT ST NO. 2 RELAY (CHECK FOR SHORT CIRCUIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON. A
The Data List item "Starter SW" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 2 relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)

B

REPLACE ST NO. 2 RELAY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 2 RELAY)
HINT:

The purpose of this step is to check for ST NO. 2 relay terminal voltage under abnormal conditions.


A435793C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.188,0.958 2.5,1.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST NO. 2 relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 2 relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A435793C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.188,0.958 2.5,1.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between ST NO. 2 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 2 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 2 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.INSPECT ENGINE STOP AND START ECU (CHECK FOR SHORT CIRCUIT)

B

6.INSPECT ENGINE STOP AND START ECU (CHECK FOR SHORT CIRCUIT)
A435793C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.188,0.958 2.5,1.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage between ST NO. 2 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 2 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 2 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the engine stop and start ECU is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

7.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

7.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A435793C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.188,0.958 2.5,1.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 2 Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST NO. 2 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 2 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) A
The voltage between ST NO. 2 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) B
The voltage between ST NO. 2 relay terminal 2 and body ground changes when the connector is disconnected. C


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - ST NO. 2 RELAY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE STOP AND START ECU - ST NO. 2 RELAY)

C

8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the engine stop and start ECU connector.


c.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-23 (STA2), A24-30 (STA) or 2 (ST NO. 2 relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


c.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

B

REPLACE ST NO. 1 RELAY

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


HINT:

The purpose of this step is to check for ST NO. 1 relay terminal voltage under abnormal conditions.


a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 1 relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

11.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
11.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the clutch start switch assembly connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the clutch start switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

12.INSPECT ENGINE STOP AND START ECU (CHECK FOR SHORT CIRCUIT)

B

12.INSPECT ENGINE STOP AND START ECU (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the engine stop and start ECU is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

13.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

13.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) A
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) B
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. C


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

14.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - CERTIFICATION ECU - ST NO. 1 RELAY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY)

C

14.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - CERTIFICATION ECU - ST NO. 1 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (STA), A81-1, A15-20 (STA), A34-21 (STA) or 2 (ST NO. 1 relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter SW
Ignition switch ON OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch to ON, GTS connected and Data List item "Starter SW" selected.


Result:
Result Proceed to
OK A
NG B


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



A

B

16.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
16.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


c.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

B

REPLACE ST NO. 1 RELAY

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


HINT:

The purpose of this step is to check for ST NO. 1 relay terminal voltage under abnormal conditions.


a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 1 relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Result Proceed to
NEXT (for Continuously Variable Transaxle Models) A
NEXT (for Manual Transaxle Models) B



A

18.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)

B

22.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
18.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

19.INSPECT TCM (CHECK FOR SHORT CIRCUIT)

B

19.INSPECT TCM (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the TCM connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the TCM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

20.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

20.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) A
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) B
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. C


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

21.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - TCM - ST NO. 1 RELAY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM - ST NO. 1 RELAY)

C

21.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - TCM - ST NO. 1 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


e.

Disconnect the TCM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (STA), C31-5 (L), A15-20 (STA), C33-28 (STA) or 2 (ST NO. 1 relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT CLUTCH START SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the clutch start switch assembly connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the clutch pedal switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

23.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

23.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A435792C01
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) A
The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) B
The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. C


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

24.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY)

B

CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

24.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (STA), A81-1, A15-20 (STA) or 2 (ST NO. 1 relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR