Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for HV Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370839 PANORAMIC VIEW MONITOR SYSTEM(for HV Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for HV Model)  C1681  Front Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1681 Front Camera Feedback Malfunction Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E379402E17
5.531,3.083 7.021,3.49 1.49,0.406 10 false Parking Assist ECU 5.531,2.917 5.99,3.115 0.458,0.198 10 false N24 5.563,0.604 6.021,0.802 0.458,0.198 10 false BCB+ 5.552,1.115 6.01,1.313 0.458,0.198 10 false BCV+ 5.552,1.594 6.01,1.792 0.458,0.198 10 false BCV- 5.24,0.51 5.677,0.708 0.438,0.198 10 false 15 5.24,0.969 5.677,1.167 0.438,0.198 10 false 36 5.229,1.479 5.667,1.677 0.438,0.198 10 false 13 5.542,2.031 6.177,2.24 0.635,0.208 10 false BGND 5.24,1.938 5.677,2.135 0.438,0.198 10 false 37 5.24,2.302 5.677,2.5 0.438,0.198 10 false 14 5.563,2.406 6.198,2.615 0.635,0.208 10 false SGND 0.104,2.875 0.563,3.073 0.458,0.198 10 false B12 0.115,3.042 2.76,3.292 2.646,0.25 10 false Front Television Camera Assembly 1.177,0.604 1.635,0.802 0.458,0.198 10 false BCB+ 1.188,1.104 1.646,1.302 0.458,0.198 10 false BCV+ 1.208,1.604 1.667,1.802 0.458,0.198 10 false BCV- 1.167,2.052 1.802,2.26 0.635,0.208 10 false BGND 1.75,0.521 2.188,0.719 0.438,0.198 10 false 6 1.719,1.01 2.156,1.208 0.438,0.198 10 false 3 1.74,1.469 2.177,1.667 0.438,0.198 10 false 2 1.75,1.938 2.188,2.135 0.438,0.198 10 false 5 3.49,2.385 3.646,2.583 0.156,0.198 10 false * 0.344,3.417 1.688,3.615 1.344,0.198 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the B12 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-15 (BCB+) - B12-6 (BCB+) Always Below 1 Ω
N24-36 (BCV+) - B12-3 (BCV+) Always Below 1 Ω
N24-13 (BCV-) - B12-2 (BCV-) Always Below 1 Ω
N24-37 (BGND) - B12-5 (BGND) Always Below 1 Ω
N24-14 (SGND) - Body ground Always 10 kΩ or higher
N24-15 (BCB+) or B12-6 (BCB+) - Body ground Always 10 kΩ or higher
N24-36 (BCV+) or B12-3 (BCV+) - Body ground Always 10 kΩ or higher
N24-13 (BCV-) or B12-2 (BCV-) - Body ground Always 10 kΩ or higher
N24-37 (BGND) or B12-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.
E330226C60
0.76,1.792 0.927,1.792 0.927,1.792 1.073,1.146 true 0.865,0.417 1.031,0.417 1.031,0.417 1.198,0.969 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.323,1.708 0.833,1.906 0.51,0.198 10 false BGND 0.458,0.323 0.958,0.479 0.5,0.156 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the N24 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
37 (BGND) - Body ground Always Below 1 Ω
13 (BCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

3.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E407111C03
1.417,0.25 1.917,0.5 0.5,0.25 1.073,0.979 0.917,0.365 0.917,0.365 0.667,0.365 true 1.073,1.167 0.865,1.906 0.865,1.906 0.615,1.906 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.26,0.281 0.729,0.479 0.469,0.198 10 false BCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.188,1.823 0.75,2.01 0.563,0.188 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-37 (BGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-15 (BCB+) - N24-37 (BGND) Power switch on (IG) 5.5 to 7.05 V
N24-15 (BCB+) - N24-37 (BGND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C87
0.75,0.292 1.25,0.542 0.5,0.25 1,1.354 0.771,1.354 0.771,1.354 0.656,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.938,2.26 0.688,2.26 0.688,2.26 0.521,1.115 true 1.063,1.271 1.656,1.573 0.594,0.302 10 false BCV+ 0.99,2.167 1.469,2.344 0.479,0.177 10 false BGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.865,0.333 1.344,0.51 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the front television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) N24-36 (BCV+) - N24-37 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Power switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG