Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for HV Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370839 PANORAMIC VIEW MONITOR SYSTEM(for HV Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for HV Model)  C1686  Driver Side Camera Video Sync Signal Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1686 Driver Side Camera Video Sync Signal Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH (for LHD)

·

Outer rear view mirror assembly LH (for LHD)

·

Side television camera assembly RH (for RHD)

·

Outer rear view mirror assembly RH (for RHD)



WIRING DIAGRAM

for LHD


E379403E12
5.708,2.823 6.167,3.021 0.458,0.198 10 false N24 5.708,3.01 7.031,3.417 1.323,0.406 10 false Parking Assist ECU 0.948,3.01 3.583,3.375 2.635,0.365 10 false Outer Rear View Mirror Assembly LH 0.74,2.365 3.156,2.615 2.417,0.25 10 false Side Television Camera Assembly LH 0.948,2.844 1.406,3.042 0.458,0.198 10 false J13 6.021,2.344 6.719,2.583 0.698,0.24 10 false SGND 6.021,1.927 6.719,2.167 0.698,0.24 10 false LGND 6.021,1.49 6.719,1.729 0.698,0.24 10 false LCV- 6,1.104 6.698,1.344 0.698,0.24 10 false LCV+ 6,0.656 6.698,0.896 0.698,0.24 10 false LCB+ 3.406,0.573 4.104,0.813 0.698,0.24 10 false LCB+ 3.406,0.958 4.104,1.198 0.698,0.24 10 false LCV+ 3.427,1.375 4.125,1.615 0.698,0.24 10 false LCV- 3.396,1.802 4.094,2.042 0.698,0.24 10 false LGND 5.698,0.594 6.01,0.792 0.313,0.198 10 false 12 5.688,0.99 6,1.188 0.313,0.198 10 false 10 5.708,1.396 6.021,1.594 0.313,0.198 10 false 34 5.719,1.833 6.031,2.031 0.313,0.198 10 false 35 5.74,2.24 6.052,2.438 0.313,0.198 10 false 11 3.906,1.802 4.219,2 0.313,0.198 10 false 11 3.885,1.375 4.198,1.573 0.313,0.198 10 false 12 3.906,0.979 4.219,1.177 0.313,0.198 10 false 4 3.906,0.573 4.219,0.771 0.313,0.198 10 false 3 4.781,2.302 4.938,2.5 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 1.219,0.698 1.917,0.938 0.698,0.24 10 false SCB+ 1.208,1.125 1.906,1.365 0.698,0.24 10 false SCV+ 1.208,1.51 1.906,1.75 0.698,0.24 10 false SCV- 1.188,1.938 1.885,2.177 0.698,0.24 10 false SGND 0.76,2.208 1.031,2.438 0.271,0.229 10 false A 1.708,0.594 2.021,0.792 0.313,0.198 10 false 1 1.719,0.969 2.031,1.167 0.313,0.198 10 false 3 1.708,1.365 2.021,1.563 0.313,0.198 10 false 7 1.708,1.813 2.021,2.01 0.313,0.198 10 false 5


for RHD


E379403E11
5.708,2.813 6.167,3.01 0.458,0.198 10 false N24 5.708,2.979 7.031,3.385 1.323,0.406 10 false Parking Assist ECU 0.938,3.042 3.573,3.406 2.635,0.365 10 false Outer Rear View Mirror Assembly RH 0.74,2.375 3.156,2.625 2.417,0.25 10 false Side Television Camera Assembly RH 0.948,2.875 1.406,3.073 0.458,0.198 10 false I13 6.021,2.344 6.719,2.583 0.698,0.24 10 false SGND 6.021,1.927 6.719,2.167 0.698,0.24 10 false RGND 6.021,1.49 6.719,1.729 0.698,0.24 10 false RCV- 6,1.104 6.698,1.344 0.698,0.24 10 false RCV+ 6,0.656 6.698,0.896 0.698,0.24 10 false RCB+ 3.396,0.573 4.094,0.813 0.698,0.24 10 false RCB+ 3.385,0.958 4.083,1.198 0.698,0.24 10 false RCV+ 3.396,1.375 4.094,1.615 0.698,0.24 10 false RCV- 3.385,1.823 4.083,2.063 0.698,0.24 10 false RGND 5.698,0.594 6.01,0.792 0.313,0.198 10 false 40 5.688,1 6,1.198 0.313,0.198 10 false 38 5.688,1.396 6,1.594 0.313,0.198 10 false 16 5.698,1.833 6.01,2.031 0.313,0.198 10 false 17 5.708,2.24 6.021,2.438 0.313,0.198 10 false 39 3.906,1.802 4.219,2 0.313,0.198 10 false 11 3.906,1.375 4.219,1.573 0.313,0.198 10 false 12 3.917,0.958 4.229,1.156 0.313,0.198 10 false 4 3.906,0.583 4.219,0.781 0.313,0.198 10 false 3 4.781,2.302 4.938,2.5 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 1.219,0.698 1.917,0.938 0.698,0.24 10 false SCB+ 1.208,1.125 1.906,1.365 0.698,0.24 10 false SCV+ 1.208,1.51 1.906,1.75 0.698,0.24 10 false SCV- 1.188,1.938 1.885,2.177 0.698,0.24 10 false SGND 0.75,2.208 1.021,2.438 0.271,0.229 10 false B 1.708,0.594 2.021,0.792 0.313,0.198 10 false 1 1.719,0.969 2.031,1.167 0.313,0.198 10 false 3 1.708,1.365 2.021,1.563 0.313,0.198 10 false 7 1.708,1.813 2.021,2.01 0.313,0.198 10 false 5


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

C

9.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the J13 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-12 (LCB+) - J13-3 (LCB+) Always Below 1 Ω
N24-10 (LCV+) - J13-4 (LCV+) Always Below 1 Ω
N24-34 (LCV-) - J13-12 (LCV-) Always Below 1 Ω
N24-35 (LGND) - J13-11 (LGND) Always Below 1 Ω
N24-12 (LCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
N24-10 (LCV+) or J13-4 (LCV+) - Body ground Always 10 kΩ or higher
N24-34 (LCV-) or J13-12 (LCV-) - Body ground Always 10 kΩ or higher
N24-35 (LGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher
N24-11 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (LCV-, LGND)
a.
E330226C62
1.698,1.802 1.469,1.802 1.469,1.802 1.375,1.156 true 0.979,1.792 1.146,1.792 1.146,1.792 1.292,1.146 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.583,1.719 1.083,1.875 0.5,0.156 10 false LGND 1.76,1.719 2.26,1.875 0.5,0.156 10 false LCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the N24 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
35 (LGND) - Body ground Always Below 1 Ω
34 (LCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

4.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.
E407111C05
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.542,0.281 2.042,0.438 0.5,0.156 10 false N24
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-12 (LCB+) - N24-35 (LGND) Power switch on (IG) 5.5 to 7.05 V
N24-12 (LCB+) - N24-35 (LGND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)
a.

Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C90
0.75,0.292 1.25,0.542 0.5,0.25 0.708,1.104 0.646,2.094 0.646,2.094 0.49,2.094 true 1.104,1.333 0.958,1.333 0.958,1.333 0.802,1.021 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1.188,1.26 1.917,1.51 0.729,0.25 10 false LCV+ 0.073,2.021 0.552,2.198 0.479,0.177 10 false LGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.875,0.323 1.354,0.5 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the power switch is on (ACC).



Measurement Condition
Item Content
Tester Connection N24-10 (LCV+) - N24-35 (LGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Power switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E407112C02
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 2,1.813 1.75,1.813 1.75,1.813 1.635,2.438 true 1.99,3.167 1.74,3.167 1.74,3.167 1.656,2.677 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false SCV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false SCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 2.052,1.719 2.667,1.917 0.615,0.198 10 false LCV+ 0.74,3.083 1.354,3.281 0.615,0.198 10 false LGND 2.042,3.083 2.656,3.281 0.615,0.198 10 false LCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.458,2.323 1.073,2.521 0.615,0.198 10 false J13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (SCB+) - J13-3 (LCB+) Always Below 1 Ω
A-3 (SCV+) - J13-4 (LCV+) Always Below 1 Ω
A-7 (SCV-) - J13-12 (LCV-) Always Below 1 Ω
A-5 (SGND) - J13-11 (LGND) Always Below 1 Ω
A-1 (SCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
A-3 (SCV+) or J13-4 (LCV+) - Body ground Always 10 kΩ or higher
A-7 (SCV-) or J13-12 (LCV-) - Body ground Always 10 kΩ or higher
A-5 (SGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

7.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the I13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-40 (RCB+) - I13-3 (RCB+) Always Below 1 Ω
N24-38 (RCV+) - I13-4 (RCV+) Always Below 1 Ω
N24-16 (RCV-) - I13-12 (RCV-) Always Below 1 Ω
N24-17 (RGND) - I13-11 (RGND) Always Below 1 Ω
N24-40 (RCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
N24-38 (RCV+) or I13-4 (RCV+) - Body ground Always 10 kΩ or higher
N24-16 (RCV-) or I13-12 (RCV-) - Body ground Always 10 kΩ or higher
N24-17 (RGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher
N24-39 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.
E330226C61
1.302,0.396 1.135,0.396 1.135,0.396 0.99,0.99 true 0.615,0.688 0.781,0.688 0.781,0.688 0.938,1 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.177,0.635 0.677,0.792 0.5,0.156 10 false RGND 1.333,0.313 1.833,0.469 0.5,0.156 10 false RCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the N24 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (RGND) - Body ground Always Below 1 Ω
16 (RCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

11.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E407111C04
1.417,0.25 1.917,0.5 0.5,0.25 0.698,0.677 0.875,0.677 0.875,0.677 0.938,1 true 0.854,1.146 0.719,1.75 0.719,1.75 0.542,1.75 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.146,1.656 0.615,1.854 0.469,0.198 10 false RCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.281,0.594 0.844,0.781 0.563,0.188 10 false RGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-17 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-40 (RCB+) - N24-17 (RGND) Power switch on (IG) 5.5 to 7.05 V
N24-40 (RCB+) - N24-17 (RGND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C88
0.75,0.302 1.25,0.552 0.5,0.25 0.646,0.74 0.5,0.74 0.5,0.74 0.406,0.99 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.74,2.177 0.594,2.177 0.594,2.177 0.469,1.104 true 0.875,2.094 1.344,2.333 0.469,0.24 10 false RCV+ 0.688,0.667 1.167,0.844 0.479,0.177 10 false RGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.875,0.333 1.354,0.51 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the power switch is on (ACC).



Measurement Condition
Item Content
Tester Connection N24-38 (RCV+) - N24-17 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Power switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

13.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
13.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E407112C01
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 2,1.813 1.75,1.813 1.75,1.813 1.635,2.438 true 1.99,3.167 1.74,3.167 1.74,3.167 1.656,2.677 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false RCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false SCV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false SCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 2.052,1.719 2.667,1.917 0.615,0.198 10 false RCV+ 0.74,3.083 1.354,3.281 0.615,0.198 10 false RGND 2.042,3.083 2.656,3.281 0.615,0.198 10 false RCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false B 0.458,2.323 1.073,2.521 0.615,0.198 10 false I13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (SCB+) - I13-3 (RCB+) Always Below 1 Ω
B-3 (SCV+) - I13-4 (RCV+) Always Below 1 Ω
B-7 (SCV-) - I13-12 (RCV-) Always Below 1 Ω
B-5 (SGND) - I13-11 (RGND) Always Below 1 Ω
B-1 (SCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
B-3 (SCV+) or I13-4 (RCV+) - Body ground Always 10 kΩ or higher
B-7 (SCV-) or I13-12 (RCV-) - Body ground Always 10 kΩ or higher
B-5 (SGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

14.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG