16535
1.INSTALL LOWER RADIATOR SUPPORT
Install the 2 lower radiator supports to the radiator assembly.
16523A
2.INSTALL RADIATOR SUPPORT CUSHION
Install the 2 radiator support cushions to the radiator assembly.
16400
3.INSTALL RADIATOR ASSEMBLY
Attach the 2 guides.
Attach the 2 claws to install the fan with motor assembly to the radiator assembly.
Do not damage the radiator assembly when installing the fan with motor assembly.
Install the radiator assembly with the fan with motor assembly to the vehicle body.
Do not apply excessive force to the cooler condenser assembly with the radiator assembly (for Inverter Coolant) or pipe and hose when installing the radiator assembly with the fan with motor assembly.
Attach the 2 guides.
Attach the 2 claws to install the cooler condenser assembly with the radiator assembly (for Inverter Coolant) to the radiator assembly.
Make sure not to damage the cooler condenser assembly with the radiator assembly (for Inverter Coolant) when installing the cooler condenser assembly with the radiator assembly (for Inverter Coolant).
for Integration Type:
| *a | Lock Lever |
Attach the 2 wire harness clamps.
Connect the cooling fan motor connector and push down the lock lever to attach the claw as shown in the illustration.
When connecting the cooling fan motor connector, make sure that the connecting parts of the cooling fan motor connector are free of dirt, water or other foreign matter.
Be sure to securely connect the cooling fan motor connector.
for Non-integration Type:
Attach the 2 wire harness clamps.
Connect the cooling fan motor connector and rotate the lever to lock it.
When connecting the cooling fan motor connector, make sure that the connecting parts of the cooling fan motor connector are free of dirt, water or other foreign matter.
Be sure to securely connect the cooling fan motor connector.
Connect the cooling fan motor connector and attach the wire harness clamp.
G9228A
4.CONNECT INVERTER COOLING HOSE
Attach the clamp to connect the No. 4 inverter cooling hose to the fan with motor assembly.
Attach the 3 clamps to connect the No. 5 inverter cooling hose to the fan with motor assembly.
16572D
5.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | RH Side | *f | 2 to 5 mm (0.0787 to 0.197 in.) |
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 2 radiator hose is securely inserted to the stopper.
Attach the clamp to connect the No. 2 radiator hose to the fan with motor assembly.
16571C
6.CONNECT NO. 1 RADIATOR HOSE (w/o Grille Shutter)
Connect the No. 1 radiator hose to the radiator assembly and slide the clip to secure it.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | RH Side | *f | 2 to 5 mm (0.0787 to 0.197 in.) |
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 1 radiator hose is securely inserted to the stopper.
Attach the clamp to connect the No. 1 radiator hose to the fan with motor assembly.
7.CONNECT RADIATOR HOSE SUB-ASSEMBLY (w/ Grille Shutter)
Connect the radiator hose sub-assembly to the radiator assembly and slide the clip to secure it.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | RH Side | *f | 2 to 5 mm (0.0787 to 0.197 in.) |
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the radiator hose sub-assembly is securely inserted to the stopper.
Attach the clamp to connect the radiator hose sub-assembly to the fan with motor assembly.
Connect the No. 2 engine coolant temperature sensor connector.
16283
8.CONNECT NO. 6 WATER BY-PASS HOSE
Connect the No. 6 water by-pass hose to the radiator assembly.
16282
9.CONNECT NO. 5 WATER BY-PASS HOSE
Connect the No. 5 water by-pass hose to the radiator assembly and slide the clip to secure it.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | Rear Side | *f | 2 to 5 mm (0.0787 to 0.197 in.) |
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 5 water by-pass hose is securely inserted to the stopper.
53205
10.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Install the upper radiator support sub-assembly with the 4 bolts.
Attach the 3 clamps to connect the wire harness to the upper radiator support sub-assembly.
Attach the 2 clamps to connect the hood lock control cable assembly to the upper radiator support sub-assembly.
Connect the 2 horn connectors.
86570
11.INSTALL VEHICLE APPROACHING SPEAKER ASSEMBLY
53510
12.INSTALL HOOD LOCK ASSEMBLY
16593B
13.INSTALL NO. 1 RADIATOR AIR GUIDE RH
Attach the guide and claw and install the No. 1 radiator air guide RH.
Install the clip.
16595B
14.INSTALL NO. 1 RADIATOR AIR GUIDE LH
w/o Grille Shutter:
Attach the guide and claw and install the No. 1 radiator air guide LH.
w/ Grille Shutter:
Attach the claw and install the No. 1 radiator air guide LH.
Install the clip.
88790B
15.INSTALL THERMISTOR ASSEMBLY (w/o Grille Shutter)
53019F
16.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)
16681A
17.INSTALL UPPER RADIATOR AIR GUIDE PLATE
Install the radiator upper air guide plate with the 5 clips.
17750A
18.INSTALL INLET AIR CLEANER ASSEMBLY
52021
19.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
52614
20.INSTALL FRONT BUMPER NO. 2 ENERGY ABSORBER
16561C
21.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator To Support Seal)
Attach the 2 guides to install the No. 1 radiator to support seal.
Install the 3 clips.
52119A
22.INSTALL FRONT BUMPER COVER
23.ADD ENGINE COOLANT
24.INSPECT FOR COOLANT LEAK
51420
25.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
51441
26.INSTALL NO. 1 ENGINE UNDER COVER
53896B
27.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
53895B
28.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH