Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly and transmission control switch (shift lock control unit assembly) detect the shift lever position and send signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic).
·

Wire harness or connector

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure Either of the following conditions is met for 2 seconds or more (2-trip detection logic).
·

2 or more of the following signals are ON simultaneously*1:

-

P or N input signal

-

R input signal

-

D input signal


·

Any of the following signals are ON simultaneously with the shift lever in M*2:

-

P input signal

-

R input signal

-

N input signal



·

Wire harness or connector

·

Park/neutral position switch assembly

·

Transmission control switch (Shift lock control unit assembly)

·

TCM


Comes on DTC stored SAE Code:
P0705

DTC Detection Condition Patterns (P070562*1):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○ ○
Malfunction Condition P input signal is ON ○ ○ - - -
R input signal is ON ○ - ○ - ○
N input signal is ON - - ○ ○ -
D input signal is ON - ○ - ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562*2):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnostic Condition Ignition switch is ON ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○
Malfunction Condition P input signal is ON ○ - -
R input signal is ON - ○ -
N input signal is ON - - ○
M input signal is ON ○ ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

DTC P070562 is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly, transmission control switch or wire harness of their circuits.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the TCM. For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (P, R, N or D).

The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will then illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait with the shift lever in each position (P, R, N or D) for 60 seconds or more with the ignition switch ON.

7.

Wait for 2 seconds or more with the shift lever in M.

8.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

9.

Input the DTC: P070513 or P070562.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C398677E06
0.365,1.604 1.875,2.229 1.51,0.625 10 false from BKUP LP Fuse 0.385,4.083 1.646,4.667 1.26,0.583 10 false from ECU-IG1 NO. 3 Fuse 2.26,3.083 3.583,3.51 1.323,0.427 10 false Park/Neutral Position Switch Assembly 2.26,2.927 2.719,3.125 0.458,0.198 10 false C31 2.021,4.677 4.063,5.24 2.042,0.563 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 2.042,4.5 2.5,4.698 0.458,0.198 10 false G23 5.74,4.708 6.198,4.906 0.458,0.198 10 false C33 5.74,4.854 6.198,5.052 0.458,0.198 10 false TCM 3.208,2.354 3.667,2.552 0.458,0.198 10 false DL 3.219,1.76 3.677,1.958 0.458,0.198 10 false NL 3.208,1.156 3.667,1.354 0.458,0.198 10 false RL 3.208,0.552 3.667,0.75 0.458,0.198 10 false PL 3.51,0.563 3.969,0.76 0.458,0.198 10 false 6 3.521,1.167 3.979,1.365 0.458,0.198 10 false 1 3.531,1.76 3.99,1.958 0.458,0.198 10 false 9 3.542,2.354 4,2.552 0.458,0.198 10 false 7 5.021,2.354 5.479,2.552 0.458,0.198 10 false 31 5,1.76 5.458,1.958 0.458,0.198 10 false 32 5.01,1.167 5.469,1.365 0.458,0.198 10 false 33 5.021,0.563 5.479,0.76 0.458,0.198 10 false 29 5.344,0.563 5.802,0.76 0.458,0.198 10 false P 5.333,1.167 5.792,1.365 0.458,0.198 10 false R 5.323,1.76 5.781,1.958 0.458,0.198 10 false N 5.323,2.365 5.781,2.563 0.458,0.198 10 false D 5.323,3.948 5.781,4.146 0.458,0.198 10 false S 5.031,3.948 5.49,4.146 0.458,0.198 10 false 30 3.5,3.948 3.958,4.146 0.458,0.198 10 false 5 3.26,3.948 3.719,4.146 0.458,0.198 10 false S 2.51,3.948 2.969,4.146 0.458,0.198 10 false IG 2.281,3.948 2.74,4.146 0.458,0.198 10 false 4 2.26,1.469 2.719,1.667 0.458,0.198 10 false 2 2.51,1.469 2.969,1.667 0.458,0.198 10 false RB

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Transmission control switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (S Range)
50003 373 27

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

3.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))
3.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))
a.

Disconnect the G23 shift lock control unit assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G23-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G23-4 (IG) - Body ground Ignition switch off Below 1 V



c.

Connect the G23 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C10
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the G23 shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



c.

Connect the G23 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)
a.

Disconnect the G23 shift lock control unit assembly connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-5 (S) - C33-30 (S) Always Below 1 Ω
G23-5 (S) or C33-30 (S) - Body ground Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the G23 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

6.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the C31 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C31-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C31-2 (RB) - Body ground Ignition switch off Below 1 V



c.

Connect the C31 park/neutral position switch assembly connector.


Result:
Proceed to
OK
NG



OK

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C193931C49
2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.583,0.5 2.333,0.5 2.333,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.688,1.833 2.438,1.833 2.438,1.833 2.135,1.49 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RB 2.635,0.406 2.958,0.604 0.323,0.198 10 false RL 0.635,1.75 1.104,1.938 0.469,0.188 10 false NL 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a 2.729,1.75 3.25,1.917 0.521,0.167 10 false PL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the C31 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
Shift lever not in D, M, "+" or "-" 10 kΩ or higher



c.

Connect the C31 park/neutral position switch assembly connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)
a.

Disconnect the C31 park/neutral position switch assembly connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-6 (PL) - C33-29 (P) Always Below 1 Ω
C31-1 (RL) - C33-33 (R) Always Below 1 Ω
C31-9 (NL) - C33-32 (N) Always Below 1 Ω
C31-7 (DL) - C33-31 (D) Always Below 1 Ω
C31-6 (PL) or C33-29 (P) - Body ground and other terminals Always 10 kΩ or higher
C31-1 (RL) or C33-33 (R) - Body ground and other terminals Always 10 kΩ or higher
C31-9 (NL) or C33-32 (N) - Body ground and other terminals Always 10 kΩ or higher
C31-7 (DL) or C33-31 (D) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the C31 park/neutral position switch assembly connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

10.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT