The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the TCM.
The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The TCM applies voltage to the temperature sensor through TCM terminal THO1 and calculates the fluid temperature based on the voltage signal.
The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071011 | Transmission Fluid Temperature Sensor "A" Circuit Short To Ground | When the battery voltage is 8 V or more and the ignition switch is ON, the CVT fluid temperature sensor voltage is less than 0.142 V for 0.5 seconds (1-trip detection logic). | ·
Wire harness or connector ·
Transmission wire (CVT fluid temperature sensor) ·
TCM |
Comes on | DTC stored | SAE Code:
P0712 |
The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the TCM determines the CVT fluid temperature and can detect a short to ground in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*, the TCM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.
*: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.
The CVT fluid temperature can be checked in the Data List.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Wait for 3 seconds or more with the ignition switch ON.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P071011.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature No.1 | CVT fluid temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 100°C (212°F): After stall speed test ·
Equal to ambient temperature: After cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted. |
| Tester Display |
|---|
| A/T Oil Temperature No.1 |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C34 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 11 (OT+) - 12 (OT-) | Always | 79 Ω to 156 kΩ |
| 11 (OT+) - Body ground and other terminals | Always | 10 kΩ or higher |
| 12 (OT-) - Body ground and other terminals | Always | 10 kΩ or higher |
If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.
| CVT Fluid Temperature | Specified Condition |
|---|---|
| 10°C (50°F) | 5.6 to 7.3 kΩ |
| 25°C (77°F) | 3.5 kΩ |
| 110°C (230°F) | 0.22 to 0.27 kΩ |
Connect the C34 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-51 (THO1) - C33-52 (ETHO) | Always | 79 Ω to 156 kΩ |
| C33-51 (THO1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-52 (ETHO) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION