Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P084000  Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance  P28287F  Pressure Control Solenoid "K" Actuator Stuck Off  


DESCRIPTION

The TCM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P084000 Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance Either of the following conditions is met (1-trip detection logic):
·

When the requested oil pressure is less than 1.0 MPa (10.2 kgf/cm2, 145 psi), the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.

·

When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is less than 0.5 MPa (5.1 kgf/cm2, 73 psi) for 2 seconds or more.


·

Oil pressure sensor

·

Transmission valve body assembly

·

TCM

·

Continuously variable transaxle assembly


Comes on DTC stored SAE Code:
P0841
P28287F Pressure Control Solenoid "K" Actuator Stuck Off Either of the following conditions is met (1-trip detection logic):
·

When the requested oil pressure is less than 1.0 MPa (10.2 kgf/cm2, 145 psi), the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.

·

When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is less than 0.5 MPa (5.1 kgf/cm2, 73 psi) for 2 seconds or more.


·

Oil pressure sensor

·

Transmission valve body assembly

·

TCM

·

Continuously variable transaxle assembly


Comes on DTC stored SAE Code:
P2829

DTC Detection Condition Patterns (P084000 and P28287F):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The requested oil pressure value is less than 1.0 MPa (10.2 kgf/cm2, 145 psi) ○ -
The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more - ○
Malfunction Condition The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more ○ -
The oil pressure sensor output value is less than 0.5 MPa (5.1 kgf/cm2, 73 psi) - ○
Duration 3 seconds or more 2 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

HINT:

These DTCs are output when either of the above detection patterns is met.


MONITOR DESCRIPTION

The TCM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or a malfunction of the oil pressure sensor is detected by the TCM, it illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P084000 or P28287F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

CAUTION:
·
C328184

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328186

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328185

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If any DTCs other than P084000 or P28287F are output, perform troubleshooting for those DTCs first.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P084000 AND P28287F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:
·

If DTC P084011 or P084015 is output, perform troubleshooting for that DTC first.

·

If DTCs P084011 and P084015 are not output but DTC P282812 or P282814 is output, perform troubleshooting for DTC P282812 or P282814 first.




Result:
Result Proceed to
Only DTC P084000 is output A
Only DTC P28287F is output B
Both DTC P084000 and P28287F are output C
DTC P084000 and/or P28287F and P084011 are output D
DTC P084000 and/or P28287F and P084015 are output E
DTC P084000 and/or P28287F and P282812 output F
DTC P084000 and/or P28287F and P282814 output G
DTC P084000 and/or P28287F and DTCs other than P084011, P084015, P282812 and P282814 are output H



A

2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

B

6.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

C

8.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

D

E

F

G

H

2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (integration control and panel assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (integration control and panel assembly) is pulled to the lock side one more time.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Turn on and off TC and TE1 (CG) connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P



h.

Enter the following menus: Powertrain / Transmission / Data List / Belt Clamping Force Sensor.


i.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi): D position stall test

·

1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi): R position stall test


-
Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

3.CHECK TCM (VCPT TERMINAL VOLTAGE)
3.CHECK TCM (VCPT TERMINAL VOLTAGE)
a.
C399499C11
1.448,0.125 1.865,0.375 0.417,0.25 1.031,1.813 1.448,1.146 true 2.323,1.813 1.906,1.146 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.365,1.74 2.677,1.938 0.313,0.198 10 false VC 0.823,1.729 1.135,1.927 0.313,0.198 10 false E2 1.531,0.167 1.99,0.365 0.458,0.198 10 false C38
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C38-3 (VC) - C38-1 (E2) Ignition switch ON 4.75 to 5.25 V



c.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE TCM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (integration control and panel assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (integration control and panel assembly) is pulled to the lock side one more time.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Turn on and off TC and TE1 (CG) connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P



h.

Enter the following menus: Powertrain / Transmission / Data List / Belt Clamping Force Sensor.


i.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi): D position stall test

·

1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi): R position stall test


-
Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

7.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
7.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (integration control and panel assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (integration control and panel assembly) is pulled to the lock side one more time.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal Turn on and off TC and TE1 (CG) connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P



h.

Enter the following menus: Powertrain / Transmission / Data List / Belt Clamping Force Sensor.


i.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi): D position stall test

·

1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi): R position stall test


-
Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

9.CHECK TCM (VCPT TERMINAL VOLTAGE)
9.CHECK TCM (VCPT TERMINAL VOLTAGE)
a.
C399499C11
1.448,0.125 1.865,0.375 0.417,0.25 1.031,1.813 1.448,1.146 true 2.323,1.813 1.906,1.146 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.365,1.74 2.677,1.938 0.313,0.198 10 false VC 0.823,1.729 1.135,1.927 0.313,0.198 10 false E2 1.531,0.167 1.99,0.365 0.458,0.198 10 false C38
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C38-3 (VC) - C38-1 (E2) Ignition switch ON 4.75 to 5.25 V



c.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SLS)

NG

13.REPLACE TCM
10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SLS)
a.

Disconnect the transmission wire connector from the shift solenoid valve SLS.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL

C398706C01
2.948,2.75 3.615,2.75 true 4.75,1.25 5.25,1.583 true 5.5,1.583 6,1.25 true 1.188,0.177 1.5,0.333 0.313,0.156 10 false *1 3.688,2.677 4,2.833 0.313,0.156 10 false *2 4.542,0.792 4.854,0.948 0.313,0.156 10 false *a 5.063,2.406 5.521,2.604 0.458,0.198 10 false (-) 5.563,2.417 6.021,2.615 0.458,0.198 10 false (+) 6.063,1.167 6.521,1.365 0.458,0.198 10 false 1 4.646,1.167 5.104,1.365 0.458,0.198 10 false 2
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SLS
*a Component without harness connected
(Shift Solenoid Valve SLS)
- -



b.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SLS connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

11.REPLACE OIL PRESSURE SENSOR

NG

12.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
11.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT