Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P170300  AT Solenoid Output Malfunction  


DESCRIPTION

The TCM controls the shift solenoid valves SL1, SL2 and SLG to change the shift mode from gear mode to belt mode and vice versa.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P170300 AT Solenoid Output Malfunction Any of the following conditions are met for 1 second or more (2-trip detection logic):
·

The C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged when 2 seconds or more have elapsed since the following conditions are met:

-

The transmission revolution sensor (NOUT) signal indicates 1200 rpm or more

-

TCM commands the C1 clutch to be released

-

TCM commands the C2 clutch to be engaged


·

When the transmission revolution sensor (NOUT) signal indicates 2050 rpm or more, the C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged.


·

Continuously variable transaxle assembly

·

Wire harness or connector

·

TCM


Comes on DTC stored SAE Code:
P1703

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 2 seconds or more have elapsed since the following conditions are met:
·

The transmission revolution sensor (NOUT) signal is 1200 rpm or more

·

TCM commands the C1 clutch to be released

·

TCM commands the C2 clutch to be engaged


○ -
The transmission revolution sensor (NOUT) signal is 2050 rpm or more - ○
Malfunction Condition C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged ○ ○
Duration 1 second or more 1 second or more
Detection Logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

The TCM monitors the changes in the shift state from belt mode to gear mode for abnormalities.

If the vehicle is being driven in gear mode when in the belt mode vehicle speed range, the TCM detects a malfunction, illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P170300.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P170300)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P170300 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P170300 is output A
DTC P170300 and other DTCs are output B



A

2.INSPECT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2, SLG)

B

2.INSPECT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2, SLG)
a.
C397724C01
1.875,1.083 0.708,0.667 true 1.875,1.333 0.708,1.75 true 2.104,1.323 2.604,1.75 true 2.281,1.333 2.75,1.5 true 2.281,1.083 2.75,0.917 true 2.125,1.094 2.615,0.667 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.792,0.844 3.292,1.042 0.5,0.198 10 false SLG+ 2.792,1.427 3.219,1.625 0.427,0.198 10 false SLG- 2.656,0.583 3.271,0.781 0.615,0.198 10 false SL1+ 2.656,1.688 3.271,1.885 0.615,0.198 10 false SL1- 0.385,1.667 1,1.865 0.615,0.198 10 false SL2- 0.354,0.583 0.969,0.781 0.615,0.198 10 false SL2+
*a Component without harness connected
(Transmission Wire)


Disconnect the C34 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SL1+) - 7 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
3 (SL2+) - 8 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
1 (SLG+) - 6 (SLG-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SL1+) or 7 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
3 (SL2+) or 8 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
1 (SLG+) or 6 (SLG-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C34 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2 AND SLG)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C33 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-38 (SL1+) - C33-37 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C33-19 (SL2+) - C33-20 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C33-21 (SLG+) - C33-22 (SLG-) 20°C (68°F) 5.0 to 5.6 Ω
C33-38 (SL1+) or C33-37 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
C33-19 (SL2+) or C33-20 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
C33-21 (SLG+) or C33-22 (SLG-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C33 TCM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

4.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2 AND SLG)
a.

Disconnect the transmission wire connector from the shift solenoid valves SL1, SL2 and SLG.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL

C398709C01
2.958,1.521 3.542,1.521 true 2.958,1.104 3.542,1.104 true 2.958,0.688 3.542,0.688 true 4.833,1.302 5.25,1.635 true 5.5,1.625 5.917,1.292 true 3.583,0.615 3.896,0.771 0.313,0.156 10 false *2 3.594,1.021 3.906,1.177 0.313,0.156 10 false *3 3.604,1.458 3.917,1.615 0.313,0.156 10 false *4 1.25,0.177 1.563,0.333 0.313,0.156 10 false *1 4.521,0.833 4.833,0.99 0.313,0.156 10 false *a 4.719,1.219 5.031,1.375 0.313,0.156 10 false 2 5.958,1.198 6.271,1.354 0.313,0.156 10 false 1
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SLG
*3 Shift Solenoid Valve SL1 *4 Shift Solenoid Valve SL2
*a Component without harness connected
(Shift Solenoid Valve SL1, SL1 and SLG)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL1 connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Shift solenoid valve SL2 connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Shift solenoid valve SLG connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



Result:
Proceed to
OK
NG



OK

NG

6.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
6.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT