Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P281F00  Pressure Control Solenoid "J" Performance/Stuck Off (2 Trip Detected)  P281F71  Pressure Control Solenoid "J" Performance/Stuck Off Actuator Stuck  


DESCRIPTION

Using the current from the TCM, the shift solenoid valve SLP controls the primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P281F00 Pressure Control Solenoid "J" Performance/Stuck Off (2 Trip Detected) Any of the following conditions are met (2-trip detection logic):
·

When the TCM commands lock-up ON, the difference between the engine speed (NE) and transmission revolution sensor (NT) signal is 250 rpm or more for 1 second or more.

·

When the TCM commands the C1 clutch to be engaged, the difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm for 1 second or more.


Continuously variable transaxle assembly (Shift solenoid valve SLP) Comes on DTC stored SAE Code:
P2820
P281F71 Pressure Control Solenoid "J" Performance/Stuck Off Actuator Stuck Any of the following conditions are met (1-trip detection logic):
·

When the oil pressure sensor output value is 0.4 MPa (4.1 kgf/cm2, 58 psi) or more and the target gear ratio is 2.0 or more, the actual gear ratio is less than 0.55 for 1.5 seconds or more.

·

When the oil pressure sensor output value is 0.4 MPa (4.1 kgf/cm2, 58 psi) or more and the target gear ratio is less than 1.1, the actual gear ratio is 1.8 or more for 2 seconds or more.


Continuously variable transaxle assembly (Shift solenoid valve SLP) Comes on DTC stored SAE Code:
P2820

DTC Detection Condition Patterns (P281F00):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The TCM commands lock-up ON ○ -
The TCM commands the C1 clutch to be engaged - ○
Malfunction Condition The difference between the engine speed (NE) and transmission revolution sensor (NT) signal is 250 rpm or more ○ -
The difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm - ○
Duration 1 second or more 1 second or more
Detection Logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P281F71):
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The oil pressure sensor output value is 0.4 MPa (4.1 kgf/cm2, 58 psi) or more ○ ○
The target gear ratio is 2.0 or more ○ -
The target gear ratio is less than 1.1 - ○
Malfunction Condition The actual gear ratio is less than 0.55 ○ -
The actual gear ratio is 1.8 or more - ○
Duration 1.5 seconds or more 2 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

HINT:

These DTCs are stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

P281F00 (Shift solenoid valve SLP OFF stuck):
Detection condition from lock-up clutch operation:
·

Under normal conditions, if the TCM commands lock-up ON, line pressure is applied to the lock up control valve from the shift solenoid valve SLU. The lock up control valve then opens to the lock-up ON side of the lock-up clutch and the lock-up clutch engages.

When the shift solenoid valve SLP is stuck OFF, if the TCM commands lock-up ON, line pressure is applied to the sequence valve from the shift solenoid valve SLP and in turn line pressure from the shift solenoid valve SLG is applied to the lock up control valve.

As a result, the lock up control valve blocks the line pressure from being applied to the lock-up ON side of the lock-up clutch and the lock-up clutch cannot be engaged.

In this case, when the TCM commands lock-up ON, it detects that lock-up is not operating (the difference between the engine speed (NE) signal and transmission revolution sensor (NT) signal exceeds the threshold) and determines that the shift solenoid valve SLP is stuck OFF, illuminates the MIL and stores a DTC.

C398252C01
0.167,4.083 7,7.667 6.833,3.583 0.167,0.25 7,3.833 6.833,3.583 0.333,0.417 0.75,0.667 0.417,0.25 10 false *A 0.354,4.25 0.75,4.5 0.396,0.25 10 false *B 1.167,2.781 1.479,2.938 0.313,0.156 10 false *1 2.135,1.99 2.448,2.146 0.313,0.156 10 false *2 2.135,0.729 2.448,0.885 0.313,0.156 10 false *3 3.167,2.885 3.479,3.042 0.313,0.156 10 false *4 4.635,2.156 4.948,2.313 0.313,0.156 10 false *5 5.885,1.854 6.198,2.01 0.313,0.156 10 false *6 1.167,6.625 1.479,6.781 0.313,0.156 10 false *1 2.146,5.833 2.458,5.99 0.313,0.156 10 false *2 2.146,4.594 2.458,4.75 0.313,0.156 10 false *3 3.167,6.552 3.479,6.708 0.313,0.156 10 false *4 4.635,5.396 4.948,5.552 0.313,0.156 10 false *5 5.854,5.708 6.167,5.865 0.313,0.156 10 false *6 5.063,1.615 5.375,1.813 0.313,0.198 10 false *b 5.073,2.094 5.385,2.292 0.313,0.198 10 false *a 5.052,5.458 5.365,5.656 0.313,0.198 10 false *b 5.052,5.927 5.365,6.125 0.313,0.198 10 false *a 1.156,6.198 1.469,6.354 0.313,0.156 10 false *c
*A TCM commands lock-up ON when shift solenoid valve SLP normal *B TCM commands lock-up ON when shift solenoid valve SLP stuck OFF
*1 Shift Solenoid Valve SLP *2 Shift Solenoid Valve SLG
*3 Shift Solenoid Valve SLU *4 Sequence Valve
*5 Lock Up Control Valve *6 Lock Up Clutch
*a Lock-up ON *b Lock-up OFF
*c Shift solenoid valve SLP stuck OFF - -
V100135

Oil Pressure Flow
V113148

Valve Movement



Detection condition from C1 clutch operation:
·

Under normal conditions, when the TCM requests the shift mode be changed to gear mode, line pressure is applied from the shift solenoid SL1 to engage the C1 clutch and gear mode is entered.

When the shift solenoid valve SLP is stuck OFF, if the TCM requests the shift mode to be changed to gear mode, line pressure from the shift solenoid valve SLP is applied to the sequence valve and in turn line pressure is applied to the clutch apply control valve.

As a result, the clutch apply control valve blocks the line pressure from being applied to the C1 clutch. The C1 clutch cannot be engaged and the shift mode cannot be changed.

In this case, when the TCM requests the shift mode to be changed to gear mode, it detects that gear mode is not entered (the C1 clutch is not engaged and the difference between the transmission revolution sensor (NT) signal and transmission revolution sensor (NC1) signal exceeds the threshold) and determines that the shift solenoid valve SLP is stuck OFF, illuminates the MIL and stores a DTC.

C398253C01
0.25,4 6.917,7.667 6.667,3.667 0.25,0.167 6.917,3.833 6.667,3.667 0.417,0.333 0.833,0.583 0.417,0.25 10 false *A 0.438,4.177 0.917,4.417 0.479,0.24 10 false *B 1.167,2.75 1.479,2.906 0.313,0.156 10 false *1 2.146,0.688 2.458,0.844 0.313,0.156 10 false *2 3.156,2.802 3.469,2.958 0.313,0.156 10 false *3 4.625,1.656 4.938,1.813 0.313,0.156 10 false *4 5.781,1.844 6.094,2 0.313,0.156 10 false *5 1.167,6.656 1.479,6.813 0.313,0.156 10 false *1 2.156,4.604 2.469,4.76 0.313,0.156 10 false *2 3.156,6.552 3.469,6.708 0.313,0.156 10 false *3 4.635,5.396 4.948,5.552 0.313,0.156 10 false *4 5.781,5.75 6.094,5.906 0.313,0.156 10 false *5 1.146,6.208 1.458,6.365 0.313,0.156 10 false *a
*A TCM commands C1 clutch engagement when shift solenoid valve SLP normal *B TCM commands C1 clutch engagement when shift solenoid valve SLP stuck OFF
*1 Shift Solenoid Valve SLP *2 Shift Solenoid Valve SL1
*3 Sequence Valve *4 Clutch Apply Control Valve
*5 C1 Clutch - -
*a Shift solenoid valve SLP stuck OFF - -
V100135

Oil Pressure Flow
V113148

Valve Movement




P281F71 (Shift solenoid valve SLP ON and OFF stuck):

The TCM compares the actual gear ratio with the target gear ratio. When the actual gear ratio and target gear ratio are different, the TCM detects the malfunction, illuminates the MIL and stores this DTC.


CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P281F00 or P281F71.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If any DTCs other than P281F00 or P281F71 are output, perform troubleshooting for those DTCs first.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P281F00 AND P281F71)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:

If DTC P281F12 or P281F14 is output, perform troubleshooting for that DTC first.



Result:
Result Proceed to
Only DTC P281F00 and/or P281F71 is output A
DTC P281F00 and/or P281F71 and P07457F, P07757F or P275600 are output B
DTC P281F00 and/or P281F71 and P281F12 are output C
DTC P281F00 and/or P281F71 and P281F14 are output D
DTC P281F00 and/or P281F71 and DTCs other than P07457F, P07757F, P275600, P281F12 and P281F14 are output E



A

2.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

2.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

C

D

E

2.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT