Using the current from the TCM, the shift solenoid valve SLP controls the primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P281F12 | Pressure Control Solenoid "J" Circuit Short to Battery | A short to +B is detected in the shift solenoid valve SLP circuit for 1 second or more (1-trip detection logic). | ·
Transmission valve body assembly (Shift solenoid valve SLP) ·
Transmission wire ·
Harness and connector ·
TCM |
Comes on | DTC stored | SAE Code:
P2827 |
This DTC indicates a short to +B in the shift solenoid valve SLP circuit. If there is a short to +B in the shift solenoid valve SLU circuit, the TCM detects the malfunction, illuminates the MIL and stores this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Test inspection in Road Test.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P281F12.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C34 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (SLP+) - Other terminals | Always | 10 kΩ or higher |
| 10 (SLP-) - Other terminals | Always | 10 kΩ or higher |
Connect the C34 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-40 (SLP+) - Other terminals | Always | 10 kΩ or higher |
| C33-39 (SLP-) - Other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the C34 transmission wire connector.
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SLP |
| *3 | Transmission Wire | - | - |
| *a | Shift Solenoid Valve Side | *b | Wire Harness Connector Side |
Disconnect the transmission wire connector from the shift solenoid valve SLP.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (shift solenoid valve side) or 5 (SLP+) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| 2 (shift solenoid valve side) or 10 (SLP-) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transmission valve body assembly.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION