Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  U010087  Lost Communication with ECM/PCM "A" Missing Message  


DESCRIPTION

The TCM communicates with the ECM via CAN communication.

If a problem occurs in this communication, the TCM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U010087 Lost Communication with ECM/PCM "A" Missing Message No communication between the TCM and ECM for 1.25 seconds or more (1-trip detection logic)
·

Harness and connector

·

ECM

·

TCM


Comes on DTC stored SAE Code:
U0100

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 3 seconds or more with the ignition switch ON.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: U010087.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C403373E01
6.146,4.198 6.604,4.396 0.458,0.198 10 false A24 6.115,4.365 6.573,4.563 0.458,0.198 10 false ECM 2.938,1.781 3.396,1.979 0.458,0.198 10 false C33 2.927,1.979 3.385,2.177 0.458,0.198 10 false TCM 3.094,0.542 3.708,0.74 0.615,0.198 10 false CAN+ 3.135,0.948 3.75,1.146 0.615,0.198 10 false CAN- 2.667,1.229 3.281,1.427 0.615,0.198 10 false E1 5.833,0.563 6.448,0.76 0.615,0.198 10 false CANP 5.833,0.948 6.448,1.146 0.615,0.198 10 false CANN 5.833,2.448 6.448,2.646 0.615,0.198 10 false +B 5.833,2.844 6.448,3.042 0.615,0.198 10 false +B2 5.844,3.25 6.458,3.448 0.615,0.198 10 false MREL 3.594,0.375 4.208,0.573 0.615,0.198 10 false 18 5.625,0.375 6.24,0.573 0.615,0.198 10 false 7 5.552,0.771 6.167,0.969 0.615,0.198 10 false 17 3.594,0.771 4.208,0.969 0.615,0.198 10 false 17 5.635,2.333 6.25,2.531 0.615,0.198 10 false 9 5.573,2.729 6.188,2.927 0.615,0.198 10 false 35 5.573,3.125 6.188,3.323 0.615,0.198 10 false 15 5.844,3.656 6.458,3.854 0.615,0.198 10 false E1 5.573,3.531 6.188,3.729 0.615,0.198 10 false 10 2.458,1.104 3.073,1.302 0.615,0.198 10 false 2 3.198,3.594 4.427,3.792 1.229,0.198 10 false EFI-MAIN NO. 1 1.167,4.063 2.396,4.26 1.229,0.198 10 false Battery 0.563,5.156 4.229,5.354 3.667,0.198 10 false : CAN Communication Line 3.292,1.365 3.906,1.563 0.615,0.198 10 false +B 3.604,1.25 4.219,1.448 0.615,0.198 10 false 1 1.333,3.042 3.479,3.24 2.146,0.198 10 false EFI-MAIN NO. 1 3.99,1.521 5.365,1.719 1.375,0.198 10 false EFI NO. 1 3.219,3.125 3.833,3.323 0.615,0.198 10 false 1 3.229,2.729 3.844,2.927 0.615,0.198 10 false 3 4.083,2.729 4.698,2.927 0.615,0.198 10 false 5 4.094,3.125 4.708,3.323 0.615,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Disconnect the A24 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-9 (+B) - A24-10 (E1) Ignition switch ON 11 to 14 V
A24-35 (+B2) - A24-10 (E1) Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Connect the A24 ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE OF ECM)

2.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the A24 ECM connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-18 (CAN+) - A24 -7 (CANP) Always Below 1 Ω
C33-17 (CAN-) - A24 -17 (CANN) Always Below 1 Ω
C33-18 (CAN+) or A24 -7 (CANP) - Body ground Always 10 kΩ or higher
C33-17 (CAN-) or A24 -17 (CANN) - Body ground Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the A24 ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - TCM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.PERFORM INITIALIZATION
4.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (DTC U010087)
5.CHECK DTC OUTPUT (DTC U010087)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Transmission / Trouble Codes.


h.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTCs are not output A
DTC U010087 is output B



A

END

B

6.REPLACE TCM
6.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT