Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B530639E01
0.823,0.156 2.563,0.375 1.74,0.219 10 false from Auxiliary Battery 1.667,1.865 3.646,2.063 1.979,0.198 10 false Horn Relay Assembly (HORN) 1.104,1.094 1.719,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 2.573,4.76 3.708,5.125 1.135,0.365 10 false Low Pitched Horn Assembly 4.198,4.75 5.344,5.125 1.146,0.375 10 false High Pitched Horn Assembly 4.406,2.167 6.021,2.573 1.615,0.406 10 false Instrument Panel Junction Block Assembly 5.375,3.396 7.052,3.927 1.677,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.948,1.458 3.167,1.656 0.219,0.198 10 false 3 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 2.052,1.438 2.271,1.635 0.219,0.198 10 false 5 2.26,4.5 2.479,4.698 0.219,0.198 10 false 1 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 2.594,4.583 2.948,4.781 0.354,0.198 10 false A7 4.198,4.573 4.552,4.771 0.354,0.198 10 false A8 4.792,4.031 7.104,4.25 2.313,0.219 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 28 5.365,3.208 5.719,3.406 0.354,0.198 10 false A 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.698,0.844 5.427,1.031 0.729,0.188 10 false 27 4.417,2.021 4.771,2.219 0.354,0.198 10 false 4F

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.


Result:
Proceed to
Horns sound
Horns do not sound



Horns sound

2.CHECK HARNESS AND CONNECTOR (HORN RELAY ASSEMBLY [HORN] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

Horns do not sound

2.CHECK HARNESS AND CONNECTOR (HORN RELAY ASSEMBLY [HORN] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Remove the horn relay assembly (HORN).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Horn relay terminal 2 - 4F-27 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.
B468454E08
1.458,0.188 1.917,0.5 0.458,0.313 1.448,1.594 1.906,1.906 0.458,0.313 1.646,0.292 1.865,0.5 0.219,0.208 10 false A 1.573,1.677 1.823,1.865 0.25,0.188 10 false 4F

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-27 - A-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG