Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2018.10–2019.09
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2762  Intrusion Sensor Signal Circuit Malfunction  


DESCRIPTION

The theft warning ultrasonic and tilt sensor conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2762 Intrusion Sensor Signal Circuit Malfunction
After normal/trouble signal is output from theft warning ultrasonic and tilt sensor as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is open

2.

Reception of signals other than normal/trouble signal


·

Map light sub-assembly

·

Theft warning ultrasonic and tilt sensor

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B503055E02
3.021,0.24 4.854,0.438 1.833,0.198 10 false ECU-B NO.2 0.594,0.083 2.021,0.385 1.427,0.302 10 false from Auxiliary Battery 1.76,0.875 3.552,1.229 1.792,0.354 10 false Theft Warning Ultrasonic and Tilt Sensor 3.854,1.417 4.167,1.604 0.313,0.188 10 false +B2 3.802,1.979 4.208,2.198 0.406,0.219 10 false IOUT 1.073,1.708 1.479,1.927 0.406,0.219 10 false 11 1.302,1.719 1.708,1.938 0.406,0.219 10 false GND 1.948,3.177 3.823,3.51 1.875,0.333 10 false Map Light Sub-assembly 4.188,1.417 4.594,1.635 0.406,0.219 10 false 9 4.188,1.979 4.594,2.198 0.406,0.219 10 false 3 5.615,1.99 6.021,2.208 0.406,0.219 10 false ISIF 5.396,1.99 5.802,2.208 0.406,0.219 10 false 14 5.333,2.854 7.01,3.26 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.344,2.708 6.896,3.063 1.552,0.354 10 false G45 6.344,1.573 6.75,1.792 0.406,0.219 10 false +B 1.948,2.979 3.823,3.313 1.875,0.333 10 false P14

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
B508345C05
1.479,0.156 1.865,0.458 0.385,0.302 2.375,1.302 2.625,1.938 2.625,1.938 2.781,1.938 true 0.927,1.542 0.823,2.01 0.823,2.01 0.677,2.01 false 1.552,0.219 2.01,0.417 0.458,0.198 10 false P14 2.844,1.844 3.302,2.042 0.458,0.198 10 false +B2 0.333,1.938 0.792,2.135 0.458,0.198 10 false GND 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Map Light Sub-assembly)


Disconnect the map light sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P14-9 (+B2) - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-11 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WAVEFORM (THEFT WARNING ULTRASONIC AND TILT SENSOR) (IOUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WAVEFORM (THEFT WARNING ULTRASONIC AND TILT SENSOR) (IOUT)
a.

Using an oscilloscope, check the waveform.

B508346C02
3.552,0.115 3.969,0.365 0.417,0.25 4.125,1.219 4.656,0.573 4.656,0.573 4.729,0.573 true 2.438,2.927 2.26,2.76 false 1.906,2.885 1.635,2.74 false 3.625,0.156 4.083,0.354 0.458,0.198 10 false P14 4.781,0.521 5.24,0.719 0.458,0.198 10 false IOUT 0.938,2.5 1.396,2.698 0.458,0.198 10 false HI 0.938,2.969 1.396,3.167 0.458,0.198 10 false LO 1.448,2.656 1.906,2.854 0.458,0.198 10 false *b 2.104,2.656 2.563,2.854 0.458,0.198 10 false *c 3.958,2.646 4.417,2.844 0.458,0.198 10 false *d 3.99,3.208 4.448,3.406 0.458,0.198 10 false *e 2.094,3.229 2.552,3.427 0.458,0.198 10 false *f 2.521,3.219 2.979,3.417 0.458,0.198 10 false *g 2.615,3.583 3.073,3.781 0.458,0.198 10 false *h 1.542,4.125 2,4.323 0.458,0.198 10 false *i 3.906,4.135 4.365,4.333 0.458,0.198 10 false *j 0.76,0.333 1.219,0.531 0.458,0.198 10 false *a
*a Component with harness connected
(Map Light Sub-assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection P14-3 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the theft warning ultrasonic and tilt sensor is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Result Proceed to
OK (There is an initial response) A
NG (Waveform output remains LO) B
NG (There is no initial response and the waveform output remains HI) C



A

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT SUB-ASSEMBLY)

C

4.INSPECT MAP LIGHT SUB-ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT SUB-ASSEMBLY)
a.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the P14 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-14 (ISIF) - P14-3 (IOUT) Always Below 1 Ω
G45-14 (ISIF) or P14-3 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT SUB-ASSEMBLY
a.

Remove the map light sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
B508344N01
1.531,0.333 1.865,0.583 0.333,0.25 1.563,1.427 1.896,1.677 0.333,0.25 0.656,1.656 0.854,1.656 0.854,1.656 1.146,2.208 true 2.75,3.01 2.594,3.01 2.594,3.01 2.406,2.49 true 2.198,1.292 2.052,1.292 2.052,1.292 1.917,1.021 true 1.135,1.271 1.333,1.271 1.333,1.271 1.479,1.01 true 2.25,0.563 2.104,0.563 2.104,0.563 1.76,0.927 true 2.667,1.615 2.521,1.615 2.521,1.615 2.073,2.219 true 1.646,0.375 1.958,0.531 0.313,0.156 10 false A 1.688,1.479 2,1.635 0.313,0.156 10 false B 2.792,2.927 3.292,3.104 0.5,0.177 10 false GND 2.719,1.542 3.125,1.719 0.406,0.177 10 false IOUT 0.375,1.563 0.771,1.729 0.396,0.167 10 false +B2 2.26,1.208 2.76,1.385 0.5,0.177 10 false GND 0.833,1.188 1.229,1.354 0.396,0.167 10 false +B2 2.292,0.49 2.698,0.667 0.406,0.177 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-11 (GND) Always Below 1 Ω
A-2 (IOUT) - B-3 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-9 (+B2) Always Below 1 Ω
A-1 (GND) or B-11 (GND) - Other terminals and body ground Always 10 kΩ or higher
A-2 (IOUT) or B-3 (IOUT) - Other terminals and body ground Always 10 kΩ or higher
A-4 (+B2) or B-9 (+B2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE THEFT WARNING ULTRASONIC AND TILT SENSOR

NG

REPLACE MAP LIGHT SUB-ASSEMBLY