The theft warning ultrasonic and tilt sensor conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).
If short to ground is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2764 | Short to GND in Intrusion Sensor Signal Circuit | After normal/trouble signal is output from theft warning ultrasonic and tilt sensor as result of self-diagnosis, following malfunctions are detected:
1.
ISIF line circuit is shorted to ground 2.
Reception of signals other than normal/trouble signal |
·
Map light sub-assembly ·
Theft warning ultrasonic and tilt sensor ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
w/ Entry and Start System:
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Map Light Sub-assembly) |
*b | IOUT Initial Signal |
| *c | IOUT Initial Response | *d | Approximately 1.0 second |
| *e | Initial Diagnosis | *f | Approximately 1.0 to 1.6 seconds |
| *g | Approximately 0.05 seconds | *h | Approximately 5.5 seconds |
| *i | Disarmed State | *j | Arming Preparation State |
| Tester Connection | Content |
|---|---|
| Tester Connection | P14-3 (IOUT) - Body ground |
| Tool Setting | 2 V/DIV., 100 ms./DIV. |
| Condition | Theft deterrent system is set (system changes from disarmed state to arming preparation state) |
If the theft warning ultrasonic and tilt sensor is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).
If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).
The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Map Light Sub-assembly) |
Disconnect the map light sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition |
|---|---|
| P14-3 (IOUT) - Body ground | Immediately after theft deterrent system set |
| Result | Proceed to |
|---|---|
| IOUT voltage is below 1 V when theft deterrent system is set | A |
| IOUT voltage is 6.5 V or higher when theft deterrent system is set | B |
With connector P14 of the map light sub-assembly disconnected, measure the voltage at IOUT when the theft deterrent system is set.
A
B
Disconnect the G45 main body ECU (multiplex network body ECU) connector.
Disconnect the P14 map light sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G45-14 (ISIF) - P14-3 (IOUT) | Always | Below 1 Ω |
| G45-14 (ISIF) or P14-3 (IOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Remove the map light sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (GND) - B-11 (GND) | Always | Below 1 Ω |
| A-2 (IOUT) - B-3 (IOUT) | Always | Below 1 Ω |
| A-4 (+B2) - B-9 (+B2) | Always | Below 1 Ω |
| A-1 (GND) or B-11 (GND) - Other terminals and body ground | Always | 10 kΩ or higher |
| A-2 (IOUT) or B-3 (IOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| A-4 (+B2) or B-9 (+B2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG