Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2018.10–2019.09
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light sub-assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the theft warning ultrasonic and tilt sensor to stop operating.

WIRING DIAGRAM

B424479E08
5.969,0.292 6.281,0.49 0.313,0.198 10 false +B 5.271,0.76 5.885,0.958 0.615,0.198 10 false SSW1 1.531,0.74 1.844,0.938 0.313,0.198 10 false 11 3.854,0.74 4.156,0.927 0.302,0.188 10 false 2 5.042,0.74 5.344,0.927 0.302,0.188 10 false 3 5.104,1.677 5.406,1.865 0.302,0.188 10 false G45 2.073,1.406 2.417,1.594 0.344,0.188 10 false P14 2.073,1.552 4.823,1.75 2.75,0.198 10 false Map Light Sub-assembly 5.104,1.833 6.76,2.24 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.802,0.75 2.146,0.938 0.344,0.188 10 false GND 3.385,0.74 3.823,0.938 0.438,0.198 10 false SOFF 1.823,0.979 3.802,1.219 1.979,0.24 10 false Intrusion Sensor Cancel Switch

CAUTION / NOTICE / HINT

NOTICE:

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENS OFF SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sens OFF SW
50003 123 203
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT SUB-ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAP LIGHT SUB-ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the P14 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-3 (SSW1) - P14-2 (SOFF) Always Below 1 Ω
P14-11 (GND) - Body ground Always Below 1 Ω
G45-3 (SSW1) or P14-2 (SOFF) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT SUB-ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT SUB-ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
B530872E02
1.49,0.125 1.99,0.406 0.5,0.281 2.427,1.292 2.719,1.729 2.719,1.729 2.802,1.729 true 2.302,1.01 2.635,0.365 2.635,0.365 2.719,0.365 true 1.656,0.208 1.958,0.438 0.302,0.229 10 false P14 2.771,0.333 3.417,0.615 0.646,0.281 10 false SOFF 2.844,1.646 3.427,1.927 0.583,0.281 10 false GND

Remove the map light sub-assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-2 (SOFF) - P14-11 (GND) Intrusion sensor cancel switch not pressed 10 kΩ or higher
P14-2 (SOFF) - P14-11 (GND) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT SUB-ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)