Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2018.10–2019.09
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic and tilt sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic and tilt sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

Any window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B503055E03
2.969,0.271 4.802,0.469 1.833,0.198 10 false ECU-B NO.2 0.594,0.083 2.021,0.385 1.427,0.302 10 false from Auxiliary Battery 1.729,0.865 3.677,1.354 1.948,0.49 10 false Intrusion Sensor (Theft Warning Ultrasonic and Tilt Sensor) 3.854,1.417 4.167,1.604 0.313,0.188 10 false +B2 3.802,1.979 4.208,2.198 0.406,0.219 10 false IOUT 1.073,1.708 1.479,1.927 0.406,0.219 10 false 11 1.302,1.719 1.708,1.938 0.406,0.219 10 false GND 1.948,3.177 3.823,3.51 1.875,0.333 10 false Map Light Sub-assembly 4.188,1.417 4.594,1.635 0.406,0.219 10 false 9 4.188,1.979 4.594,2.198 0.406,0.219 10 false 3 5.615,1.99 6.021,2.208 0.406,0.219 10 false ISIF 5.396,1.99 5.802,2.208 0.406,0.219 10 false 14 5.333,2.854 7.01,3.26 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.344,2.708 6.896,3.063 1.552,0.354 10 false G45 6.344,1.573 6.75,1.792 0.406,0.219 10 false +B 1.948,2.979 3.823,3.313 1.875,0.333 10 false P14

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

HINT:

When performing the above inspection, have the electrical key transmitter sub-assembly in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).*


NOTICE:

Make sure that all windows are closed.


*: w/ Entry and Start System



f.

From inside the vehicle, put your hand in front of the intrusion sensor (theft warning ultrasonic and tilt sensor) and move it back and forth a distance of 0.3 m (0.984 ft.) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the intrusion sensor (theft warning ultrasonic and tilt sensor) detection ON or OFF ON: Moving object detected by sensor
OFF: Both of the conditions below is met
·

No moving object detected by sensor

·

Vehicle tilt not detected by sensor


-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204
OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic and tilt sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B508346C02
3.552,0.115 3.969,0.365 0.417,0.25 4.125,1.219 4.656,0.573 4.656,0.573 4.729,0.573 true 2.438,2.927 2.26,2.76 false 1.906,2.885 1.635,2.74 false 3.625,0.156 4.083,0.354 0.458,0.198 10 false P14 4.781,0.521 5.24,0.719 0.458,0.198 10 false IOUT 0.938,2.5 1.396,2.698 0.458,0.198 10 false HI 0.938,2.969 1.396,3.167 0.458,0.198 10 false LO 1.448,2.656 1.906,2.854 0.458,0.198 10 false *b 2.104,2.656 2.563,2.854 0.458,0.198 10 false *c 3.958,2.646 4.417,2.844 0.458,0.198 10 false *d 3.99,3.208 4.448,3.406 0.458,0.198 10 false *e 2.094,3.229 2.552,3.427 0.458,0.198 10 false *f 2.521,3.219 2.979,3.417 0.458,0.198 10 false *g 2.615,3.583 3.073,3.781 0.458,0.198 10 false *h 1.542,4.125 2,4.323 0.458,0.198 10 false *i 3.906,4.135 4.365,4.333 0.458,0.198 10 false *j 0.76,0.333 1.219,0.531 0.458,0.198 10 false *a
*a Component with harness connected
(Map Light Sub-assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection P14-3 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic and tilt sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT SUB-ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT SUB-ASSEMBLY)
a.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the P14 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-14 (ISIF) - P14-3 (IOUT) Always Below 1 Ω
G45-14 (ISIF) or P14-3 (IOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT SUB-ASSEMBLY
a.

Remove the map light sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
B508344N01
1.531,0.333 1.865,0.583 0.333,0.25 1.563,1.427 1.896,1.677 0.333,0.25 0.656,1.656 0.854,1.656 0.854,1.656 1.146,2.208 true 2.75,3.01 2.594,3.01 2.594,3.01 2.406,2.49 true 2.198,1.292 2.052,1.292 2.052,1.292 1.917,1.021 true 1.135,1.271 1.333,1.271 1.333,1.271 1.479,1.01 true 2.25,0.563 2.104,0.563 2.104,0.563 1.76,0.927 true 2.667,1.615 2.521,1.615 2.521,1.615 2.073,2.219 true 1.646,0.375 1.958,0.531 0.313,0.156 10 false A 1.688,1.479 2,1.635 0.313,0.156 10 false B 2.792,2.927 3.292,3.104 0.5,0.177 10 false GND 2.719,1.542 3.125,1.719 0.406,0.177 10 false IOUT 0.375,1.563 0.771,1.729 0.396,0.167 10 false +B2 2.26,1.208 2.76,1.385 0.5,0.177 10 false GND 0.833,1.188 1.229,1.354 0.396,0.167 10 false +B2 2.292,0.49 2.698,0.667 0.406,0.177 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) - B-11 (GND) Always Below 1 Ω
A-2 (IOUT) - B-3 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-9 (+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)

NG

REPLACE MAP LIGHT SUB-ASSEMBLY