Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2018.10–2019.09
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Tilt Sensor Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) operates the tilt sensor (theft warning ultrasonic and tilt sensor) via the ISIF communication line. The tilt sensor (theft warning ultrasonic and tilt sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.

HINT:

In the following situations, the tilt sensor (theft warning ultrasonic and tilt sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.

·

The vehicle is transported by a ferry, trailer or train.

·

The vehicle is parked in a multi-story parking facility.

·

The vehicle is washed by an automatic car wash.

·

A tire blows out.

·

The vehicle is jacked up for a tire or wheel change.

·

An earthquake occurs or the road subsides.

·

Goods such as skis or snowboards are loaded or unloaded.



WIRING DIAGRAM

B503055E04
2.969,0.271 4.802,0.469 1.833,0.198 10 false ECU- B NO.2 0.594,0.083 2.021,0.385 1.427,0.302 10 false from Auxiliary Battery 1.76,0.875 3.427,1.26 1.667,0.385 10 false Tilt Sensor (Theft Warning Ultrasonic and Tilt Sensor) 3.854,1.417 4.167,1.604 0.313,0.188 10 false +B2 3.802,1.979 4.208,2.198 0.406,0.219 10 false IOUT 1.073,1.708 1.479,1.927 0.406,0.219 10 false 11 1.302,1.719 1.708,1.938 0.406,0.219 10 false GND 1.948,3.177 3.823,3.51 1.875,0.333 10 false Map Light Sub-assembly 4.188,1.417 4.594,1.635 0.406,0.219 10 false 9 4.188,1.979 4.594,2.198 0.406,0.219 10 false 3 5.615,1.99 6.021,2.208 0.406,0.219 10 false ISIF 5.396,1.99 5.802,2.208 0.406,0.219 10 false 14 5.333,2.854 7.01,3.26 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.344,2.708 6.896,3.063 1.552,0.354 10 false G45 6.344,1.573 6.75,1.792 0.406,0.219 10 false +B 1.948,2.979 3.823,3.313 1.875,0.333 10 false P14

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the tilt sensor (theft warning ultrasonic and tilt sensor) detection ON or OFF ON: Vehicle tilt detected by sensor
OFF: Both of the conditions below is met
·

No moving object detected by sensor

·

Vehicle tilt not detected by sensor


-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204
NOTICE:
B530835C01
2.198,0.813 2.427,0.292 2.427,0.292 2.521,0.292 true 2.323,0.875 3.104,1.813 3.104,1.813 3.198,1.813 true 1.333,0.823 1.563,0.302 1.563,0.302 1.656,0.302 true 0.271,1.813 0.333,1.813 0.333,1.813 1.167,0.927 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *1 1.698,0.229 2.01,0.385 0.313,0.156 10 false *a 0.073,1.729 0.385,1.885 0.313,0.156 10 false *b 2.583,0.208 2.896,0.365 0.313,0.156 10 false *a 3.219,1.729 3.427,1.906 0.208,0.177 10 false *b
*1 Map Light Sub-assembly
*a Intrusion Sensor (Theft Warning Ultrasonic and Tilt Sensor)
*b Protective Tape


·

Be sure to cover the 2 intrusion sensors in the map light sub-assembly with protective tape to prevent detected by the intrusion sensor.

·

After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), tilt the vehicle and confirm the Data List (jack up the vehicle so that the tires are in the air).



HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).*


*: w/ Entry and Start System


OK:

The display on the GTS changes according to the detection condition of the tilt sensor (theft warning ultrasonic and tilt sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (TILT SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
2.CHECK WAVEFORM (TILT SENSOR [THEFT WARNING ULTRASONIC AND TILT SENSOR]) (IOUT)
a.

Using an oscilloscope, check the waveform.

B508346C02
3.552,0.115 3.969,0.365 0.417,0.25 4.125,1.219 4.656,0.573 4.656,0.573 4.729,0.573 true 2.438,2.927 2.26,2.76 false 1.906,2.885 1.635,2.74 false 3.625,0.156 4.083,0.354 0.458,0.198 10 false P14 4.781,0.521 5.24,0.719 0.458,0.198 10 false IOUT 0.938,2.5 1.396,2.698 0.458,0.198 10 false HI 0.938,2.969 1.396,3.167 0.458,0.198 10 false LO 1.448,2.656 1.906,2.854 0.458,0.198 10 false *b 2.104,2.656 2.563,2.854 0.458,0.198 10 false *c 3.958,2.646 4.417,2.844 0.458,0.198 10 false *d 3.99,3.208 4.448,3.406 0.458,0.198 10 false *e 2.094,3.229 2.552,3.427 0.458,0.198 10 false *f 2.521,3.219 2.979,3.417 0.458,0.198 10 false *g 2.615,3.583 3.073,3.781 0.458,0.198 10 false *h 1.542,4.125 2,4.323 0.458,0.198 10 false *i 3.906,4.135 4.365,4.333 0.458,0.198 10 false *j 0.76,0.333 1.219,0.531 0.458,0.198 10 false *a
*a Component with harness connected
(Map Light Sub-assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection P14-3 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the tilt sensor (theft warning ultrasonic and tilt sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT SUB-ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT SUB-ASSEMBLY)
a.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the P14 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-14 (ISIF) - P14-3 (IOUT) Always Below 1 Ω
G45-14 (ISIF) - Body ground Always 10 kΩ or higher
P14-3 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TILT SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR