Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Shift Paddle Switch Circuit  


DESCRIPTION

Moving the shift lever to M enables the shift range to be selected. The shift range can be selected by operating the "+" or "-" shift paddle switch.

WIRING DIAGRAM

C399502E04
2.281,0.156 4.479,0.542 2.198,0.385 10 false to Shift Lock Control Unit Assembly (Transmission Control Switch) 0.188,1.708 2.042,2.25 1.854,0.542 10 false Shift Paddle Switch RH (No. 2 Transmission Shift Switch Assembly) 0.177,4.177 2.021,4.729 1.844,0.552 10 false Shift Paddle Switch LH (No. 1 Transmission Shift Switch Assembly) 2.438,4.177 3.24,4.563 0.802,0.385 10 false No. 1 Switch Wire 3.51,4.167 4.615,4.594 1.104,0.427 10 false Spiral Cable Sub-assembly 6.313,3.438 6.771,3.635 0.458,0.198 10 false C33 6.333,5.031 6.792,5.229 0.458,0.198 10 false A24 6.323,3.594 6.781,3.792 0.458,0.198 10 false TCM 6.333,5.188 6.792,5.385 0.458,0.198 10 false ECM 6.573,0.75 6.938,0.99 0.365,0.24 10 false 12 V 6.583,2.781 6.948,3.021 0.365,0.24 10 false 12 V 4.531,3.896 4.99,4.094 0.458,0.198 10 false G20 4.531,3.063 4.99,3.26 0.458,0.198 10 false G20 4.521,1.042 4.979,1.24 0.458,0.198 10 false G20 3.365,1.021 3.823,1.219 0.458,0.198 10 false z5 3.354,3.052 3.813,3.25 0.458,0.198 10 false z5 3.344,3.875 3.802,4.073 0.458,0.198 10 false z5 2.188,3.052 2.344,3.25 0.156,0.198 10 false A 2.188,3.458 2.344,3.656 0.156,0.198 10 false A 2.188,3.875 2.344,4.073 0.156,0.198 10 false A 2.198,1.021 2.354,1.219 0.156,0.198 10 false B 2.198,1.438 2.354,1.635 0.156,0.198 10 false B 5.938,0.917 6.552,1.115 0.615,0.198 10 false SFTU 4.135,0.917 4.75,1.115 0.615,0.198 10 false SUP 3.677,0.917 4.292,1.115 0.615,0.198 10 false SUP 2.927,0.917 3.542,1.115 0.615,0.198 10 false SUP 2.49,0.917 3.104,1.115 0.615,0.198 10 false SUP 1.719,0.917 2.333,1.115 0.615,0.198 10 false SUP 5.938,2.938 6.552,3.135 0.615,0.198 10 false SFTD 4.125,2.938 4.74,3.135 0.615,0.198 10 false SDN 3.667,2.938 4.281,3.135 0.615,0.198 10 false SDN 2.927,2.938 3.542,3.135 0.615,0.198 10 false SDN 2.49,2.938 3.104,3.135 0.615,0.198 10 false SDN 1.708,2.938 2.323,3.135 0.615,0.198 10 false SDN 1.698,3.76 2.313,3.958 0.615,0.198 10 false ECC 2.49,3.76 3.104,3.958 0.615,0.198 10 false ECC 2.906,3.76 3.521,3.958 0.615,0.198 10 false ECC 3.677,3.76 4.292,3.958 0.615,0.198 10 false ECC 4.125,3.76 4.74,3.958 0.615,0.198 10 false ECC 5.938,4.219 6.552,4.417 0.615,0.198 10 false ECCS 5.938,4.688 6.552,4.885 0.615,0.198 10 false E1 5.667,0.917 5.979,1.115 0.313,0.198 10 false 14 4.604,3.677 4.917,3.875 0.313,0.198 10 false 2 4.594,2.844 4.906,3.042 0.313,0.198 10 false 1 4.604,0.823 4.917,1.021 0.313,0.198 10 false 8 5.688,2.938 6,3.135 0.313,0.198 10 false 13 3.406,0.813 3.719,1.01 0.313,0.198 10 false 2 3.396,2.844 3.708,3.042 0.313,0.198 10 false 4 3.396,3.667 3.708,3.865 0.313,0.198 10 false 3 2.198,3.677 2.51,3.875 0.313,0.198 10 false 2 2.198,3.25 2.51,3.448 0.313,0.198 10 false 3 2.208,2.833 2.521,3.031 0.313,0.198 10 false 1 2.219,1.219 2.531,1.417 0.313,0.198 10 false 2 2.208,0.823 2.521,1.021 0.313,0.198 10 false 1 5.677,4.094 5.99,4.292 0.313,0.198 10 false 28 5.677,4.563 5.99,4.76 0.313,0.198 10 false 10 1.698,3.354 2.313,3.552 0.615,0.198 10 false ECC' 2.479,3.354 3.094,3.552 0.615,0.198 10 false ECC' 1.698,1.323 2.313,1.521 0.615,0.198 10 false ECC' 2.49,1.333 3.104,1.531 0.615,0.198 10 false ECC'

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" or "+" shift paddle switch operated

·

OFF: Shift lever not held in "+" and "+" shift paddle switch released


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" or "-" shift paddle switch operated

·

OFF: Shift lever not held in "-" and "-" shift paddle switch released


-
Powertrain > Transmission > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 373 26,25

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

2.CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH CIRCUIT)
a.

Disconnect the C33 TCM connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-14 (SFTU) - A24-28 (ECCS) "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher
C33-13 (SFTD) - A24-28 (ECCS) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher



d.

Connect the A24 ECM connector.


e.

Connect the C33 TCM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM - ECM)
3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-10 (E1) - Body ground Always Below 1 Ω



c.

Connect the A24 ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (ECM TERMINALS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)

4.CHECK ECM (ECM TERMINALS)
a.
A402881C12
1.479,0.135 1.917,0.365 0.438,0.229 2.885,1.375 2.594,1.375 2.594,1.375 2.323,1.063 true 0.531,0.917 1.042,0.917 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 1.583,0.177 2.042,0.375 0.458,0.198 10 false A24 0.333,0.833 0.646,1.031 0.313,0.198 10 false E1 2.927,1.292 3.365,1.469 0.438,0.177 10 false ECCS
*a Component without harness connected
(ECM)


Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-28 (ECCS) - A24-10 (E1) Always Below 1 Ω



c.

Connect the A24 ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

6.REPLACE ECM
5.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM - ECM)
a.

Disconnect the G20 spiral cable sub-assembly connector.


b.

Disconnect the C33 TCM connector.


c.

Disconnect the A24 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-14 (SFTU) - G20-8 (SUP) Always Below 1 Ω
C33-13 (SFTD) - G20-1 (SDN) Always Below 1 Ω
A24-28 (ECCS) - G20-2 (ECC) Always Below 1 Ω
C33-14 (SFTU) or G20-8 (SUP) - Body ground Always 10 kΩ or higher
C33-13 (SFTD) or G20-1 (SDN) - Body ground Always 10 kΩ or higher
A24-28 (ECCS) or G20-2 (ECC) - Body ground Always 10 kΩ or higher



e.

Connect the A24 ECM connector.


f.

Connect the C33 TCM connector.


g.

Connect the G20 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

8.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM - ECM)

8.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT SHIFT PADDLE SWITCH LH (NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

9.INSPECT SHIFT PADDLE SWITCH LH (NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY)
a.
C370677C15
1.552,0.167 1.885,0.417 0.333,0.25 1,1.667 1.417,1.167 true 1.5,1.667 1.667,1.167 true 2.5,1.667 2,1.167 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.781,1.667 1.396,1.865 0.615,0.198 10 false ECC' 1.354,1.667 1.969,1.865 0.615,0.198 10 false ECC 2.396,1.667 3.01,1.865 0.615,0.198 10 false SDN 1.677,0.208 1.833,0.406 0.156,0.198 10 false A
*a Component without harness connected
(Shift Paddle Switch LH (No. 1 Transmission Shift Switch Assembly))


Remove the shift paddle switch LH (No. 1 transmission shift switch assembly).

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (SDN) - A-2 (ECC) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
A-1 (SDN) - A-3 (ECC') "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT SHIFT PADDLE SWITCH RH (NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY)

NG

REPLACE SHIFT PADDLE SWITCH LH (NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY)

10.INSPECT SHIFT PADDLE SWITCH RH (NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY)
a.
C370677C16
1.542,0.167 1.875,0.417 0.333,0.25 1.5,1.667 1.667,1.167 true 2.167,1.667 2,1.167 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.354,1.667 1.969,1.865 0.615,0.198 10 false ECC' 2.042,1.667 2.656,1.865 0.615,0.198 10 false SUP 1.667,0.208 1.823,0.406 0.156,0.198 10 false B
*a Component without harness connected
(Shift Paddle Switch RH (No. 2 Transmission Shift Switch Assembly))


Remove the shift paddle switch RH (No. 2 transmission shift switch assembly).

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>SHIFT PADDLE SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (SUP) - B-2 (ECC') "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT NO. 1 SWITCH WIRE

NG

REPLACE SHIFT PADDLE SWITCH RH (NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY)

11.INSPECT NO. 1 SWITCH WIRE
a.
C338575C34
1.5,0.177 1.917,0.427 0.417,0.25 1.844,1.365 2.344,1.698 true 1.573,1.354 1.073,1.688 true 2.333,0.667 1.833,1 true 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.635,0.219 1.948,0.417 0.313,0.198 10 false z5 0.75,1.635 1.208,1.833 0.458,0.198 10 false ECC 2.385,1.635 2.844,1.833 0.458,0.198 10 false SDN 2.375,0.583 2.833,0.781 0.458,0.198 10 false SUP
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Install the shift paddle switch LH (No. 1 transmission shift switch assembly) and shift paddle switch RH (No. 2 transmission shift switch assembly).

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>SHIFT PADDLE SWITCH>INSTALLATION


b.

Disconnect the z5 No. 1 switch wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (SUP) - z5-3 (ECC) "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher
z5-4 (SDN) - z5-3 (ECC) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TCM

NG

12.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT