Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _076527 WINDOW / GLASS _0373365 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also the dynamic radar cruise control system (for HV Model), dynamic radar cruise control system (for Gasoline Model), front camera system, lane control system, road sign assist system, front radar sensor system, pre-collision system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.

·

Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or equivalent.



PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a gasket scraper, remove any remaining stopper, cover, moulding, adhesive dam, double-sided tape and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.




b.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.




Hide 56115A 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2 Peace Type)

a.
B526619C01
0,0 0,0 false
V113147

Install in this Direction


Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 3.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a brush or sponge, coat the installation area of 2 No. 2 windshield glass stoppers with glass primer.

B526620C01
1.24,0.417 2.125,0.219 2.125,0.219 1.927,0.427 false 1.583,0.417 2.115,0.229 false 6,0.469 5.021,0.219 5.021,0.219 5.271,0.458 false 5.615,0.438 5.052,0.24 false 0.094,1.396 0.406,1.594 0.313,0.198 10 false *a 2.875,0.604 3.188,0.802 0.313,0.198 10 false b 4.844,0.135 5.156,0.333 0.313,0.198 10 false *b 4.198,0.667 4.51,0.865 0.313,0.198 10 false b 5.604,1.094 5.917,1.292 0.313,0.198 10 false a 1.531,1.063 1.844,1.26 0.313,0.198 10 false a 2.198,0.146 2.51,0.344 0.313,0.198 10 false *b
*a Backside *b Ceramic Notch
V100155

Glass Primer Application Area - -


NOTICE:

Do not apply too much primer.


Standard Dimension:
Area Dimension
a 82 mm (3.23 in.)
b 20 mm (0.787 in.)



b.

Remove the peeling paper from a new No. 2 windshield glass stopper.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the 2 No. 2 windshield stoppers to the windshield glass as shown in the illustration.

B526621C01
1.583,0.729 2.083,1.135 false 0.427,0.771 0.583,0.563 false 6.76,0.771 6.583,0.563 false 6.24,1.125 5.625,0.729 true 1.563,1.125 1.281,1.448 false 5.604,1.115 5.854,1.458 false 1.125,1.438 1.438,1.594 0.313,0.156 10 true *b 6.271,1.094 6.583,1.25 0.313,0.156 10 false *c 6.75,0.781 7.063,0.938 0.313,0.156 10 false *d 0.094,1.406 0.406,1.563 0.313,0.156 10 false *a 5.875,1.49 6.188,1.646 0.313,0.156 10 false *b 2.115,1.094 2.427,1.25 0.313,0.156 10 false *c 0.271,0.792 0.583,0.948 0.313,0.156 10 false *d 1.104,0.188 1.26,0.385 0.156,0.198 10 false b 5.188,0.188 5.344,0.385 0.156,0.198 10 false b 1.938,0.188 2.094,0.385 0.156,0.198 10 false b 5.979,0.198 6.135,0.396 0.156,0.198 10 false b 2.719,0.583 2.875,0.781 0.156,0.198 10 false a 4.365,0.583 4.521,0.781 0.156,0.198 10 false a
*a Backside *b Stopper Center line
*c Ceramic Notch *d Windshield Glass Edge Side


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Make sure to install the No. 2 windshield glass stopper in the correct orientation.



HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.


Standard Dimension:
Area Dimension
a 10.7 to 11.7 mm (0.421 to 0.460 in.)
b 40 mm (1.57 in.)



Hide 75533G 4.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the glass primer to the windshield outside moulding installation surface of the windshield glass.

NOTICE:

Do not apply too much primer.



b.

Remove the peeling paper from a new windshield outside moulding.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the windshield outside moulding to the windshield glass as shown in the illustration.

B526624C01
1.208,3.042 1.281,3.229 false 5.927,3.063 5.865,3.219 false 0.177,0.146 0.49,0.302 0.313,0.156 10 false *a 1.271,3.25 1.583,3.406 0.313,0.156 10 false *b 5.75,3.219 6.063,3.375 0.313,0.156 10 false *b 0.698,2.885 0.854,3.083 0.156,0.198 10 false a 6.396,2.885 6.552,3.083 0.156,0.198 10 false a
*a Backside *b Ceramic Notch
V100155

Windshield Outside Moulding - -


NOTICE:

Allow the primer to dry for 3 minutes or more.


Standard Dimension:
Area Dimension
a 5.0 mm (0.197 in.) to -5.0 mm (-0.197 in.)



Hide 56117A 5.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the glass primer to the window glass adhesive dam installation surface of the windshield glass.

NOTICE:

Do not apply too much primer.



b.

Remove the peeling paper from a new window glass adhesive dam.

NOTICE:

Allow the primer to dry for 3 minutes or more.


HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the window glass adhesive dam to the windshield glass as shown in the illustration.

B526622C01
1.24,3.073 1.073,3.198 false 5.917,3.073 6.104,3.177 false 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a 0.906,3.146 1.219,3.344 0.313,0.198 10 false *b 6.177,3.135 6.49,3.333 0.313,0.198 10 false *b
*a Backside *b Ceramic Notch
V100155

Window Glass Adhesive Dam - -



Hide 56165 6.INSTALL FRONT WINDOW INNER MOULDING COVER LH (w/ Cover)

a.

Using a brush or sponge, coat the glass primer to the front window inner moulding cover LH installation surface of the windshield glass.

NOTICE:

Do not apply too much primer.



b.

Remove the peeling paper from a new front window inner moulding cover LH.

NOTICE:

Allow the primer to dry for 3 minutes or more.


HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the front window inner moulding cover LH to the windshield glass as shown in the illustration.

B532154C01
5.052,1.427 5.646,1.229 5.646,1.229 5.333,1.573 false 2.063,1.25 2.219,1.448 0.156,0.198 10 false A 1.865,2.333 2.021,2.531 0.156,0.198 10 false A 3.979,0.271 4.5,0.49 0.521,0.219 10 false A-A 5.01,0.688 5.167,0.885 0.156,0.198 10 false a 1.042,2.177 1.198,2.375 0.156,0.198 10 false a 5.667,1.115 5.979,1.313 0.313,0.198 10 false *b 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a
*a Backside *b Ceramic Line for ID-Plate
V100155

Front Window Inner Moulding Cover LH - -


NOTICE:

Allow the primer to dry for 3 minutes or more.


Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.)



Hide 56153C 7.INSTALL FRONT WINDOW INNER CENTER MOULDING

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



HINT:

Perform the following procedures if replacing the front window inner center moulding.


a.

Using a heat light, heat the windshield glass and a new front window inner center moulding.

Standard:
Item Temperature
Windshield Glass 20 to 30°C (68 to 86°F)
Front Window Inner Center Moulding 20 to 30°C (68 to 86°F)



b.
B526626C01
0.813,2.594 0.646,2.552 false 2.604,2.594 2.823,2.552 false 1.708,4.26 2.177,4.448 false 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 0.479,2.448 0.792,2.604 0.313,0.156 10 false *b 2.854,2.479 3.167,2.635 0.313,0.156 10 false *b 2.073,3.938 2.229,4.135 0.156,0.198 10 false a 2.24,4.406 2.552,4.563 0.313,0.156 10 false *c
*a Backside
*b Ceramic Notch
*c R End
V100155

Glass Primer


Using a brush or sponge, coat the glass primer to the front window inner center moulding installation surface of the windshield glass.

Standard Dimension:
Area Dimension
a 17.5 mm (0.689 in.) to 20.5 mm (0.807 in.)


NOTICE:

Do not apply too much primer.



c.

Remove the peeling paper from a new front window inner center moulding.

NOTICE:

Allow the primer to dry for 3 minutes or more.


HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the front window inner center moulding to the windshield glass as shown in the illustration.

B526627C01
0.667,2.781 0.49,2.792 false 5.083,2.792 5.229,2.771 false 6.094,2.094 5.719,2.323 false 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 0.344,2.708 0.656,2.865 0.313,0.156 10 false *b 5.573,2.26 5.885,2.417 0.313,0.156 10 false *c 5.25,2.677 5.563,2.833 0.313,0.156 10 false *b 2.594,2.125 2.75,2.323 0.156,0.198 10 true A 2.615,2.813 2.771,3.01 0.156,0.198 10 true A 5.542,0.792 6,0.99 0.458,0.198 10 false A-A 5.604,1.615 5.76,1.813 0.156,0.198 10 false a
*a Backside *b Ceramic Notch
*c Liner for the Protection - -
V100155

Front Window Inner Center Moulding - -


NOTICE:
·

Do not remove the protective liner off the front window inner center moulding until the windshield glass is installed to the body.

·

Allow the primer to dry for 3 minutes or more.



Standard Dimension:
Area Dimension
a 0.6 mm (0.0236 in.)



Hide 56111 8.INSTALL WINDSHIELD GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B470006C01
0.667,0.458 1.208,0.813 false 0.5,0.375 0.813,0.531 0.313,0.156 10 false *a 1.573,0.927 1.729,1.125 0.156,0.198 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.




b.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.

NOTICE:

w/ Windshield Deicer:

Make sure that the wire harness of the windshield deicer is not caught between the body and windshield glass.



iii.
B526613C01
1.813,0.438 2.24,0.25 2.24,0.25 1.813,0.781 true 2.313,0.125 2.625,0.323 0.313,0.198 10 false *a
*a Matchmarks


When using a new windshield glass:

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

NOTICE:

Check that the No. 2 windshield glass stopper are attached to the No. 1 windshield glass stopper correctly.


HINT:

When reusing a windshield glass, check the position of the matchmarks and make adjustments.



iv.

Using suction cups, remove the windshield glass.


v.

Using a brush or sponge, coat the body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




vi.

Using a brush or sponge, coat the glass primer as shown in the illustration.

B526628C01
0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.781,0.583 1.917,0.781 0.135,0.198 10 false A 1.792,1.302 1.927,1.5 0.135,0.198 10 true A 1,1.302 1.156,1.5 0.156,0.198 10 true B 1,0.594 1.156,0.792 0.156,0.198 10 true B 0.646,1.813 0.802,2.01 0.156,0.198 10 true C 0.063,1.813 0.219,2.01 0.156,0.198 10 true C 2.76,3.031 2.917,3.229 0.156,0.198 10 true D 2.615,2.281 2.771,2.479 0.156,0.198 10 true D 5.625,0.656 6.083,0.854 0.458,0.198 10 false A-A 4.021,0.677 4.479,0.875 0.458,0.198 10 false B-B 4.01,1.875 4.469,2.073 0.458,0.198 10 false C-C 5.646,1.865 6.104,2.063 0.458,0.198 10 false D-D 4.635,1.917 4.792,2.115 0.156,0.198 10 false a 6.406,2.073 6.563,2.271 0.156,0.198 10 false b 6.302,0.948 6.458,1.146 0.156,0.198 10 false a
*a Backside - -
V100155

Glass Primer - -


Standard Dimension:
Area Dimension
a 9.1 mm (0.358 in.)
b 19 mm (0.748 in.)


NOTICE:

Do not apply too much primer.



vii.
B214800C84
1.354,0.583 1.177,0.479 false 2.917,0.375 2.521,0.542 true 0.583,0.667 0.74,0.854 0.156,0.188 10 false a 1.271,1.448 1.417,1.635 0.146,0.188 10 false a 1.125,0.865 1.25,1.063 0.125,0.198 10 false b 0.771,1.031 0.917,1.177 0.146,0.146 10 false b 1.406,0.531 1.604,0.698 0.198,0.167 10 false *b 2.979,0.302 3.177,0.469 0.198,0.167 10 false *a
*a Sealer Gun
*b Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 mm (0.472 in.) to 15 mm (0.591 in.)
b 8.0 mm (0.315 in.) to 11 mm (0.433 in.)



viii.

Load the sealer gun with the cartridge.


ix.

Apply adhesive to the glass as shown in the illustration.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


B526629C01
2.448,2.698 2.208,3.146 false 3.25,2.563 3.427,3.115 false 5.875,1.688 6.281,1.51 true 4.083,1.677 4.49,1.5 true 4.365,2.698 4.76,3.146 true 6.167,2.552 5.792,2.833 5.792,2.833 6.344,2.698 true 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.823,0.583 1.979,0.781 0.156,0.198 10 false A 1.802,1.302 1.958,1.5 0.156,0.198 10 true A 0.969,0.563 1.125,0.76 0.156,0.198 10 false B 0.99,1.281 1.146,1.479 0.156,0.198 10 true B 0.583,1.896 0.74,2.094 0.156,0.198 10 true C 0.042,1.771 0.198,1.969 0.156,0.198 10 true C 2.49,2.292 2.646,2.49 0.156,0.198 10 true D 2.615,2.969 2.771,3.167 0.156,0.198 10 true D 5.563,0.792 6.021,0.99 0.458,0.198 10 false A-A 3.917,0.76 4.375,0.958 0.458,0.198 10 false B-B 3.896,2 4.354,2.198 0.458,0.198 10 false C-C 5.615,1.938 6.073,2.135 0.458,0.198 10 false D-D 6.458,0.948 6.615,1.146 0.156,0.198 10 false a 6.802,2.469 6.958,2.667 0.156,0.198 10 false b 6.604,1.906 6.76,2.104 0.156,0.198 10 false c 4.667,0.927 4.823,1.125 0.156,0.198 10 false a 4.396,2.052 4.552,2.25 0.156,0.198 10 false a 3.385,3.156 3.698,3.354 0.313,0.198 10 false *c 2.083,3.188 2.396,3.385 0.313,0.198 10 false *b 4.792,3.188 5.104,3.385 0.313,0.198 10 false *b 5.615,2.781 5.927,2.979 0.313,0.198 10 false *b 5.708,1.604 6.021,1.802 0.313,0.198 10 false *b 3.917,1.625 4.229,1.823 0.313,0.198 10 false *b
*a Backside *b Adhesive Positioning Center
*c Ceramic Notch - -
V100155

Adhesive - -


NOTICE:

Allow the primer to dry for 3 minutes or more.


Standard Dimension:
Area Dimension
a 2.0 mm (0.0787 in.)
b 4.0 mm (0.158 in.)
c 8.0 mm (0.315 in.)




c.
B526613C01
1.813,0.438 2.24,0.25 2.24,0.25 1.813,0.781 true 2.313,0.125 2.625,0.323 0.313,0.198 10 false *a
*a Matchmarks


Install the windshield glass to the vehicle body.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned.

NOTICE:
·

Check that the No. 1 windshield stopper and the No. 2 windshield stopper are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




ii.

Press it in gently along the rim.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a gasket scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive up to the edge of the windshield glass.



iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




d.
B533151C01
0.156,0.104 0.531,0.344 0.375,0.24 12 true *A 0.156,2.5 0.531,2.74 0.375,0.24 12 true *B
*A for Type A
*B for Type B


w/ Windshield deicer:

i.

Attach the clamp and connect the windshield deicer connector.



e.
B526610

w/ Heated Windshield Defroster System:

i.

Connect the windshield deicer connector.



f.
B526630C01
2.292,1.896 2.448,2.094 0.156,0.198 10 true A 2.396,2.771 2.552,2.969 0.156,0.198 10 true A 1.083,2.906 1.542,3.104 0.458,0.198 10 false A-A
V100155

Liner for the Protection


When replacing the front window inner center moulding:

Remove the 2 protective liners of the front window inner center moulding.

NOTICE:

Do not damage or deform the front window inner center moulding.



Hide 86401 10.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Pre-collision System)

Hide 8646C 11.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

Hide 86464A 12.INSTALL FORWARD RECOGNITION LATCH (w/ Pre-collision System)

Hide 87810 13.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 14.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87810 15.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (for Digital Inner Mirror)

Hide 86466D 16.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 86466E 17.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 89941 18.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 88620E 19.INSTALL AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Hide 20.INSTALL MAP LIGHT ASSEMBLY

Hide 74610U 21.INSTALL ASSIST GRIP ASSEMBLY

Hide 74320 23.INSTALL VISOR ASSEMBLY LH

Hide 74310 24.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 25.INSTALL FRONT PILLAR GARNISH LH

Hide 62211 26.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 28.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 55708 29.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 30.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 31.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 32.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 33.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 85292B 34.INSTALL FRONT WIPER ARM HEAD CAP

Hide 35. CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


c.

Remove the protective tape and match mark.


Hide 8646C 36.ADJUST FORWARD RECOGNITION CAMERA