These DTCs are stored when a malfunction occurs in the navigation antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Connection Malfunction(short) | GPS Antenna Connection Malfunction(short) | w/o GPS Antenna Divider
·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Navigation ECU w/ GPS Antenna Divider
·
Antenna divider ·
No. 1 amplifier antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
No. 4 antenna cord sub-assembly ·
Navigation ECU |
| B15C1 | GPS Antenna Connection Malfunction(break) | GPS Antenna Connection Malfunction(break) | w/o GPS Antenna Divider
·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Navigation ECU w/ GPS Antenna Divider
·
Antenna divider ·
No. 1 amplifier antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
No. 4 antenna cord sub-assembly ·
Navigation ECU |
When replacing the navigation ECU, always replace it with a new one. If a navigation ECU which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The navigation ECU may not operate normally.
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
When inspect the No. 1 Antenna Cord Sub-assembly, check if the Antenna Divider is equipped.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| w/o GPS Antenna Divider | A |
| w/ GPS Antenna Divider | B |
A
B
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the navigation antenna assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-6 | Always | Below 1 Ω |
| A-3a - B-6a | Always | Below 1 Ω |
| A-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the antenna connector from the antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 - C-1 (GPS) | Always | Below 1 Ω |
| B-6a - C-1a | Always | Below 1 Ω |
| B-6 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
| *a | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 1 amplifier antenna assembly.
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-5 - E-1 | Always | Below 1 Ω |
| D-5a - E-1a | Always | Below 1 Ω |
| D-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| w/ DAB Function | A |
| w/o DAB Function | B |
A
B
| *a | Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 - F-1 | Always | Below 1 Ω |
| E-1a - F-1a | Always | Below 1 Ω |
| E-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-1 - G-6 | Always | Below 1 Ω |
| F-1a - G-6a | Always | Below 1 Ω |
| G-2 - H-6 | Always | Below 1 Ω |
| G-2a - H-6a | Always | Below 1 Ω |
| F-1 - Body ground | Always | 10 kΩ or higher |
| G-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
| *a | Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 - F-5 | Always | Below 1 Ω |
| E-1a - F-5a | Always | Below 1 Ω |
| E-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-5 - G-6 | Always | Below 1 Ω |
| F-5a - G-6a | Always | Below 1 Ω |
| G-2 - H-6 | Always | Below 1 Ω |
| G-2a - H-6a | Always | Below 1 Ω |
| F-5 - Body ground | Always | 10 kΩ or higher |
| G-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 2 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the antenna connector from the antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 - C-1 (GPS) | Always | Below 1 Ω |
| B-6a - C-1a | Always | Below 1 Ω |
| B-6 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 amplifier antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna divider with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG