Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD (for Instrument Panel) › 2018.10–2019.02
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370108 RADIO ANTENNA CORD(for Instrument Panel) A

AUDIO / VIDEO  RADIO ANTENNA CORD(for Instrument Panel)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 6.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 55950G 7.REMOVE DEFROSTER NOZZLE ASSEMBLY

Hide 55086 8.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55972C 9.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Hide 86101 10.REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/o Telematics Transceiver, w/ Navigation ECU:

i.

Detach the claw and disconnect the connector.


ii.

Detach the clamp and remove the antenna cord sub-assembly.

E406823



b.

w/ Antenna Divider:

i.

Disconnect the connector.


ii.

Detach the clamp and remove the antenna cord sub-assembly.

E406825C01
1.354,1.927 2.135,2.344 0.781,0.417 1.385,1.948 1.667,2.188 0.281,0.24 12 true *A
*A w/ Telematics Transceiver - -




Hide 86101 11.REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

w/o Telematics Transceiver, w/ Navigation ECU:

i.

Detach the claw and disconnect the connector.


ii.

Detach the clamp and remove the antenna cord sub-assembly.

E406824



b.

w/ Antenna Divider:

i.

Detach the claw and disconnect the connector.


ii.

Detach the clamp and remove the antenna cord sub-assembly.

E406826C01
1.771,2.146 2.656,2.563 0.885,0.417 1.792,2.167 2.063,2.396 0.271,0.229 12 true *A
*A w/ Telematics Transceiver - -




c.

w/o Telematics Transceiver, w/o Navigation ECU:

i.

Detach the claw and disconnect the connector.


ii.

Detach the clamp and remove the antenna cord sub-assembly.

E406827