Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3620E _55 Steering _076851 POWER ASSIST SYSTEMS _0374399 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  Drive Mode Select Switch Circuit  


DESCRIPTION

The electronic throttle and the EPS character change by the operation of the drive mode select switch (integration control and panel assembly).

WIRING DIAGRAM

for Gasoline Model:
C409031E02
5.344,0.313 5.656,0.51 0.313,0.198 10 false 10 5.375,1.063 5.688,1.26 0.313,0.198 10 false 11 5.792,0.49 6.406,0.688 0.615,0.198 10 false CANH 5.802,1.219 6.417,1.417 0.615,0.198 10 false CANL 5.865,1.625 6.854,1.979 0.99,0.354 10 false Power Steering ECU 4.552,0.313 4.708,0.51 0.156,0.198 10 false 8 4.521,1.052 4.833,1.25 0.313,0.198 10 false 18 4.094,0.458 4.708,0.656 0.615,0.198 10 false CANH 4.125,1.219 4.74,1.417 0.615,0.198 10 false CANL 3.375,0.479 3.99,0.677 0.615,0.198 10 false SPCN 3.365,1.24 3.979,1.438 0.615,0.198 10 false PWMS 3.135,2.531 3.75,2.729 0.615,0.198 10 false ECOS 5.51,2.76 5.969,2.958 0.458,0.198 10 false C54 5.521,2.948 7.104,3.344 1.583,0.396 10 false Rack and Pinion Power Steering Gear Assembly 3.021,0.375 3.635,0.573 0.615,0.198 10 false 41*2 3,1.104 3.615,1.302 0.615,0.198 10 false 31*2 2.688,0.375 3.302,0.573 0.615,0.198 10 false 13*1 2.688,1.104 3.302,1.302 0.615,0.198 10 false 12*1 3.375,1.656 4.24,1.969 0.865,0.313 10 false A24 ECM 3.125,3.021 3.583,3.219 0.458,0.198 10 false G46 1.635,0.479 2.094,0.677 0.458,0.198 10 false G32 1.635,1.229 2.094,1.427 0.458,0.198 10 false G32 1.625,2.531 2.083,2.729 0.458,0.198 10 false G32 1.646,3.135 2.104,3.333 0.458,0.198 10 false G32 1.979,0.479 2.469,0.635 0.49,0.156 10 false G111 1.969,1.229 2.458,1.385 0.49,0.156 10 false G111 1.979,2.531 2.469,2.688 0.49,0.156 10 false G111 1.99,3.135 2.479,3.292 0.49,0.156 10 false G111 0.26,3.698 2.688,4.073 2.427,0.375 10 false Drive Mode Select Switch (Integration Control and Panel Assembly) 1.417,0.354 1.573,0.552 0.156,0.198 10 false B 1.417,1.115 1.573,1.313 0.156,0.198 10 false P 1.24,2.406 1.698,2.604 0.458,0.198 10 false ECU 1.26,3 1.719,3.198 0.458,0.198 10 false GND 1.646,2.938 1.958,3.135 0.313,0.198 10 false 13*3 2.052,2.938 2.375,3.135 0.323,0.198 10 false 6*4 1.656,2.313 1.958,2.49 0.302,0.177 10 false 7*3 2.021,2.313 2.344,2.552 0.323,0.24 10 false 10*4 1.656,0.302 1.938,0.521 0.281,0.219 10 false 8*3 1.656,1.042 1.906,1.292 0.25,0.25 10 false 9*3 2.031,1.031 2.354,1.229 0.323,0.198 10 false 8*4 2.031,0.292 2.344,0.458 0.313,0.167 10 false 9*4 3.083,3.906 4.167,4.115 1.083,0.208 10 false *1: for A25A-FKS 4.25,3.906 5.385,4.104 1.135,0.198 10 false *2: for M20A-FKS 5.365,3.906 6.427,4.115 1.063,0.208 10 false *3: for A/T CVT 6.344,3.896 7.063,4.115 0.719,0.219 10 false *4: for M/T 4.698,4.396 6.479,4.625 1.781,0.229 10 false : CAN Communication Line 3.135,3.188 4.917,3.604 1.781,0.417 10 false Air Conditioning Amplifier Assembly 2.865,2.406 3.177,2.604 0.313,0.198 10 false 11

for HV Model:
C409299E01
1.323,0.365 1.479,0.563 0.156,0.198 10 false B 1.344,1.094 1.5,1.292 0.156,0.198 10 false P 1.167,2.406 1.625,2.604 0.458,0.198 10 false ECU 1.167,3.021 1.625,3.219 0.458,0.198 10 false GND 2.792,1.208 3.406,1.406 0.615,0.198 10 false SPRT 2.781,0.469 3.396,0.667 0.615,0.198 10 false NORM 1.573,0.365 1.729,0.563 0.156,0.198 10 false 8 1.563,1.083 1.719,1.281 0.156,0.198 10 false 9 2,1.052 2.313,1.25 0.313,0.198 10 false 37*1 1.99,0.281 2.302,0.479 0.313,0.198 10 false 38*1 5.792,0.479 6.406,0.677 0.615,0.198 10 false CANH 5.792,1.219 6.406,1.417 0.615,0.198 10 false CANL 3.719,0.469 4.333,0.667 0.615,0.198 10 false CA1H 3.75,1.208 4.365,1.406 0.615,0.198 10 false CA1L 3.188,2.531 3.802,2.729 0.615,0.198 10 false ECOS 3.104,3.083 3.563,3.281 0.458,0.198 10 false G46 3.115,3.292 4.719,3.656 1.604,0.365 10 false Air Conditioning Amplifier Assembly 0.188,3.688 0.646,3.885 0.458,0.198 10 false G32 0.188,3.885 2.615,4.25 2.427,0.365 10 false Drive Mode Select Switch (Integration Control and Panel Assembly) 1.594,2.396 1.75,2.594 0.156,0.198 10 false 7 1.563,2.99 1.875,3.188 0.313,0.198 10 false 13 2.854,2.365 3.167,2.563 0.313,0.198 10 false 11 4.656,4.406 6.479,4.615 1.823,0.208 10 false : CAN Communication Line 5.323,0.313 5.635,0.51 0.313,0.198 10 false 10 5.313,1.063 5.625,1.26 0.313,0.198 10 false 11 5.781,1.604 6.771,1.99 0.99,0.385 10 false Power Steering ECU 5.552,2.76 6.01,2.958 0.458,0.198 10 false C54 5.552,2.948 7.094,3.354 1.542,0.406 10 false Rack and Pinion Power Steering Gear Assembly 4.219,1.052 4.531,1.25 0.313,0.198 10 false 8*1 4.188,0.292 4.51,0.479 0.323,0.188 10 false 21*1 2.427,1.646 4.917,1.917 2.49,0.271 10 false Hybrid Vehicle Control ECU Assembly 4.813,3.896 5.542,4.083 0.729,0.188 10 false *1: for LHD 5.604,3.896 6.302,4.094 0.698,0.198 10 false *2: for RHD 2.031,0.49 2.49,0.688 0.458,0.198 10 false A30 2.031,1.24 2.458,1.469 0.427,0.229 10 false A30 2.396,0.49 2.854,0.688 0.458,0.198 10 false G63 2.406,1.24 2.865,1.438 0.458,0.198 10 false G63 2.396,0.281 3.01,0.479 0.615,0.198 10 false 38*2 2.375,1.042 2.99,1.24 0.615,0.198 10 false 37*2 4.208,0.49 4.667,0.688 0.458,0.198 10 false A31 4.208,1.229 4.667,1.427 0.458,0.198 10 false A31 4.563,0.49 5.021,0.688 0.458,0.198 10 false G64 4.573,1.229 5.031,1.427 0.458,0.198 10 false G64 4.552,0.292 5.167,0.49 0.615,0.198 10 false 21*2 4.594,1.052 5.052,1.25 0.458,0.198 10 false 8*2

PROCEDURE

1.CHECK THE PROBLEM SYMPTOMS
a.

Check each symptom by checking the suspected areas in the table below.


Result:
Result Proceed to
SPORT mode or NORMAL mode is abnormal. A
ECO mode is abnormal. B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

3.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - BODY GROUND)
a.

Turn the ignition switch off.


b.

for HV, A/T or CVT:

i.

Disconnect the G32 drive mode select switch (integration control and panel assembly) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-13 (GND) - Body ground Always Below 1 Ω




c.

for M/T:

i.

Disconnect the G111 drive mode select switch (integration control and panel assembly) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G111-6 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

Result:
Result Proceed to
for A25A-FKS: Drive mode select switch (integration control and panel assembly) is normal A
for A25A-FXS: Drive mode select switch (integration control and panel assembly) is normal B
for M20A-FKS: Drive mode select switch (integration control and panel assembly) is normal C
Drive mode select switch (integration control and panel assembly) is abnormal D



A

5.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - ECM)

B

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

7.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - ECM)

D

5.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - ECM)
a.

Reconnect the G32 drive mode select switch (integration control and panel assembly) connector.


b.

Disconnect the A24 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-12 (PWMS) - Body ground SPORT mode switch being turned and held Below 1 Ω
A24-12 (PWMS) - Body ground SPORT mode switch not turned 10 kΩ or higher
A24-13 (SPCN) - Body ground NORMAL mode switch being pushed and held Below 1 Ω
A24-13 (SPCN) - Body ground NORMAL mode switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Reconnect the G32 drive mode select switch (integration control and panel assembly) connector.


b.

for LHD:

i.

Disconnect the A30 hybrid vehicle control ECU assembly connectors.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-37 (SPRT) - Body ground SPORT mode switch being turned and held Below 1 Ω
A30-37 (SPRT) - Body ground SPORT mode switch not turned 10 kΩ or higher
A30-38 (NORM) - Body ground NORMAL mode switch being pushed and held Below 1 Ω
A30-38 (NORM) - Body ground NORMAL mode switch not pushed 10 kΩ or higher




c.

for RHD:

i.

Disconnect the G63 hybrid vehicle control ECU assembly connectors.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-37 (SPRT) - Body ground SPORT mode switch being turned and held Below 1 Ω
G63-37 (SPRT) - Body ground SPORT mode switch not turned 10 kΩ or higher
G63-38 (NORM) - Body ground NORMAL mode switch being pushed and held Below 1 Ω
G63-38 (NORM) - Body ground NORMAL mode switch not pushed 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - ECM)
a.

Reconnect the G32*1, G111*2 drive mode select switch (integration control and panel assembly) connector.

*1: for CVT

*2: for M/T


b.

Disconnect the A24 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-31 (PWMS) - Body ground SPORT mode switch being turned and held Below 1 Ω
A24-31 (PWMS) - Body ground SPORT mode switch not turned 10 kΩ or higher
A24-41 (SPCN) - Body ground NORMAL mode switch being pushed and held Below 1 Ω
A24-41 (SPCN) - Body ground NORMAL mode switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR